CSCheng Song

Cheng Song

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Cheng Song has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Control mechanism of vortex-generator jet on turbulent separation in a highly loaded compressor cascade

    by Cao Zhiyuan, Song Cheng, Guo Wei, Wang Chuxuan, Gao Xi, Liu Bo

    The active flow control technique of vortex-generator jet (VGJ) was used to control the turbulent separation of a highly loaded compressor cascade at a high incidence. VGJ schemes on suction surface with different jet locations, skewed angles, pitch angles were numerically performed and the control mechanism of VGJ parameters on the flow field of the cascade was revealed. For avoiding the effect of endwall boundary layer, both endwall surfaces of the cascade were set to translational periodicity boundary (TPB). Results show that VGJ significantly eliminates the turbulent separation and improves the performance of cascade. The overall loss coefficient of cascade is reduced by 52.3% at most. The optimal VGJ location in this study is not separation location but 7% axial chord downstream of it, which is probably due to the ultra-high loading of the cascade. The spanwise location and intensity of jet vortices are mainly affected by skewed angle, and will increase with the skewed angle. The VGJ case with a higher pitch angle features better control effect on suction surface but increases the pitchwise scale of the low-velocity region. In addition, as pitch angle increases, the mixing loss between mainstream and jet flow increases, which brings a negative effect on cascade performance. In order to enhance the momentum transporting between mainstream flow and separation flow, counter vortex-generator jet (CVGJ) schemes were designed and studied. Though CVGJ strengthens the jet vortices near the trailing edge and achieves minimum loss near TPB sections at 150% axial chord section, the interaction of jet vortices with opposite rotating direction brings extra loss, which leads to the control effect of CVGJ is weaker than that of VGJ.

  • Open Access

    Effects of pulsed endwall air injection on corner separation and vortical flow of a compressor cascade

    by Zhiyuan Cao, Cheng Song, Xi Gao, Xiang Zhang, Fei Zhang, Bo Liu

    Air injection is an effective method to eliminate flow separation and improve blade loading in compressors. In existing studies on unsteady air injection, achieving a better control effect than steady injection with lower injection consumption is a major difficulty and challenge. In this work, pulsed endwall air injection (PEAI) was carried out numerically in a highly loaded compressor cascade under different injection frequencies and injection amplitudes. The mechanism through which PEAI influences corner separation and vortical flow, especially the effect of initial injection phase on the flow field of compressor cascade, was revealed. The results showed that PEAI effectively suppressed the corner separation with lower injection mass flow rate compared with steady endwall air injection (SEAI). The time-averaged overall loss coefficient and endwall loss coefficient were reduced by 10.5% and 28.7%, respectively, under the optimal PEAI scheme. Higher injection amplitude exhibited a more effectively controlled range in the suction corner, which led to a decrease in corner separation and deterioration of the mid-span flow field. The interaction between trailing edge separation and low-momentum fluid at mid-span led to the formation of an injection vortex. When conducting PEAI, the effect of inertia was observed for flow in the injection hole, which was derived from the interactions between injection fluid at different velocities and will increase with the improvement of injection frequency. The effects of injection location and diameter of the injection hole were also investigated. The injection location of PEAI affected the flow field by changing the effect region of the injection and low-momentum fluid near the endwall. The injection hole diameter had a significant impact on the intensity of the passage vortex and mid-span flow field.


  • Performance enhancing for a highly loaded tandem cascade by endwall incoming vortex–corner separation interaction

    by Zhiyuan Cao, Xi Gao, Cheng Song, Xiang Zhang, Fei Zhang, Bo Liu

    In highly loaded tandem compressor cascades, corner separations can still exist. In order to eliminate corner separations in highly loaded tandem compressor cascades, incoming vortex–corner separation interaction mechanism was investigated. Different schemes of the vortex generators, which located at different pitchwise locations and could generate vortexes with different rotation directions, were designed and investigated numerically. Results show that, severe corner separation occurred at the front blade passage of the tandem cascade; by utilizing flow control method of incoming vortex–corner separation interaction, the corner separation could be reduced significantly. The optimal control effect of incoming vortex on corner separation was achieved with anticlockwise rotation and the vortex generator is located right ahead of the leading edge of tandem cascade, a maximum loss coefficient reduction of 21.8% being achieved. Different from single blade configuration, the boundary layer of tandem cascade was regenerated at rear blade suction surface due to the injection flow from blade gap between the two blades. Though corner separations could be reduced at both conditions, the loss of tandem cascade with clockwise incoming vortex is higher than that with anticlockwise vortex, and a smaller corner separation region at suction surface was achieved by utilizing clockwise vortex. The mechanism was that anticlockwise incoming vortex reduced the corner separation but increased secondary flow, while clockwise vortex enhanced passage vortex and decreased secondary flow. For clockwise incoming vortex near pressure surface, the vortex would be divided into two parts at the leading edge of rear blade, one would go through the blade gap and deteriorate flow fluid near rear blade suction surface, the other flowed downstream along pressure surface. The rotation direction of different incoming vortexes became the same as the passage vortex at rear blade passage of tandem cascade, which was mainly due to the effect of secondary flow.


  • Flow physics of highly loaded tandem compressor cascade with non-axisymmetric endwall profiling

    by Zhiyuan Cao, Wei Guo, Cheng Song, Bo Liu

    Tandem configuration is an effective methodology to reduce flow separation on compressor blade suction surface and to improve blade loading. However, in modern highly loaded cases, corner separation remains as its single blade counterpart. In this study, non-axisymmetric endwall profiling (NAEP) was utilized in a highly loaded tandem cascade (diffusion factor D = 0.69), aiming at reducing its severe corner separation and revealing the unique flow mechanism while NAEP is utilized in tandem cascade. NAEP was designed in both forward (F) blade and rare (R) blade separately, and was investigated numerically in tandem environment. Results show that, NAEP in F blade passage can effectively eliminate the corner separation and reduce loss generation, whereas NAEP in R blade passage has no positive effect on corner separation and even promotes loss production. The optimal NAEP approximately removes the corner separation completely, with loss coefficient reducing by as much as 37.8%. The optimal NAEP for the tandem cascade features optimal axial location at the origin of corner separation. There is an optimal NAEP height (0.02 of blade height), under which NAEP can achieve pretty good control effect while the peak of NAEP varies in a large axial location range. In the tandem configuration, it is found that NAEP transfers blade loading from R blade to F blade; the static pressure increases significantly for the entire cascade, but the static pressure distribution of F blade does not exhibit as the design intent of NAEP. In addition, it is interesting to find that the flow turning near endwall reduces after endwall profiling, which is unique in tandem cascade and is contrast to the view on conventional configuration. On the contrary, NAEP in R blade has no influence on the corner separation of the tandem cascade; due to the decrement of cross-passage pressure gradient for R blade, the flow overturning near endwall reduces.


  • Influence of endwall slotted injection on performance and flow physics in a compressor cascade

    by Zhiyuan Cao, Cheng Song, Bo Liu, Limin Gao

    Air injection is an effectively methodology to suppress flow separation and to improve blade loading of airfoils and compressors. In order to remove corner separations in a cascade, investigation of endwall slotted injection was carried out numerically in this study. Based on endwall slot schemes of other flow control methods, six different endwall slots were designed, aiming at revealing the axial location effect and pitchwise location effect. For each endwall slot, numerical simulations were performed with six different injection directions to uncover the injection direction effect. Results showed that endwall slotted injection can effectively remove the corner separation. The overall loss coefficient and endwall loss coefficient of the cascade were reduced by 10.3% and 36.8% at most, respectively. Injection from leading edge and mid-chord can reduce endwall loss; however, the optimal axial location of endwall slot is near the trailing edge, where the corner separation is located. Different with other flow control methods, in general, the optimal pitchwise location of endwall slot is not close to suction surface but 0.16 pitch away from it. Injection near the suction surface is more sensitive to injection direction compared with injection at 0.16 pitch away from suction surface. Injection with velocity components both downstream and toward suction surface promises optimal control effect on corner separation. However, at mid-span, trailing edge separation is deteriorated and the flow turning angle is reduced, the flow mechanism being that the low-momentum fluid migrates along spanwise.