Yinghua Jian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yinghua Jian has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Dunwen Liu
School of Resources and Safety Engineering, Central South University, Changsha 410083, China
8 shared publications - Yu Tang
College of Water Resources and Civil Engineering, Hunan Agricultural University, Changsha 410128, China
7 shared publications - Wanmao Zhang
School of Resources and Safety Engineering, Central South University, Changsha 410083, China
5 shared publications - Chun Gong
School of Resources and Safety Engineering, Central South University, Changsha 410000, China
3 shared publications - Haofei Chen
School of Resources and Safety Engineering, Central South University, Changsha 410083, China
2 shared publications - Kunpeng Cao
School of Resources and Safety Engineering, Central South University, Changsha 410083, China
2 shared publications
Latest Publications
- Open Access
- 17 April 2025
- Published by MDPI AG in Fractal and Fractional
- Vol. 9 (4) , 254
Compression Damage Precursors of Silane-Protected Concrete Under Sulfate Erosion Based on Acoustic Emission Characterization
Concrete materials exposed to sulfate-rich geological environments are prone to structural durability degradation due to chemical erosion. Silane-based protective materials can enhance the durability of concrete structures under harsh environmental conditions. This study investigates the evolution of acoustic emission (AE) precursor characteristics in silane-protected, sulfate-eroded concrete specimens during uniaxial compression failure. Unlike existing research focused primarily on protective material properties, this work establishes a novel framework linking “silane treatment–AE parameters–failure precursor identification”, thereby bridging the research gap in damage evolution analysis of sulfate-eroded concrete under silane protection. Uniaxial compressive strength tests and AE monitoring were conducted on both silane-protected and unprotected sulfate-eroded concrete specimens. A diagnostic system integrating dynamic analysis of the acoustic emission b-value, mutation detection of energy concentration index ρ, and multifractal detrended fluctuation analysis (MF-DFA) was developed. The results demonstrate that silane-protected specimens exhibited a distinct b-value escalation followed by an abrupt decline prior to peak load, whereas unprotected specimens showed disordered fluctuations. The mutation point of energy concentration ρ for silane-protected specimens occurred at 0.83 σc, representing a 9.2% threshold elevation compared to 0.76 σc for unprotected specimens, confirming delayed damage accumulation in protected specimens. MF-DFA revealed narrowing spectrum width () in unprotected specimens, indicating reduced heterogeneity in AE signals, while protected specimens maintained significant multifractal divergence. peak localization revealed that weak AE signals dominated during early loading stages in both groups, with crack evolution primarily involving sliding and friction. During the mid-late elastic phase, crack propagation became the predominant failure mode. Experimental evidence confirms the engineering significance of silane protection in extending service life of concrete structures in sulfate environments. The proposed multi-parameter AE diagnostic methodology provides quantitative criteria for the safety monitoring of protected concrete structures in sulfate-rich conditions.- 17 April 2025
- Published by MDPI AG in Fractal and Fractional
- Vol. 9 (4) , 254
Open AccessCompression Damage Precursors of Silane-Protected Concrete Under Sulfate Erosion Based on Acoustic Emission Characterization
Concrete materials exposed to sulfate-rich geological environments are prone to structural durability degradation due to chemical erosion. Silane-based protective materials can enhance the durability of concrete structures under harsh environmental conditions. This study investigates the evolution of acoustic emission (AE) precursor characteristics in silane-protected, sulfate-eroded concrete specimens during uniaxial compression failure. Unlike existing research focused primarily on protective material properties, this work establishes a novel framework linking “silane treatment–AE parameters–failure precursor identification”, thereby bridging the research gap in damage evolution analysis of sulfate-eroded concrete under silane protection. Uniaxial compressive strength tests and AE monitoring were conducted on both silane-protected and unprotected sulfate-eroded concrete specimens. A diagnostic system integrating dynamic analysis of the acoustic emission b-value, mutation detection of energy concentration index ρ, and multifractal detrended fluctuation analysis (MF-DFA) was developed. The results demonstrate that silane-protected specimens exhibited a distinct b-value escalation followed by an abrupt decline prior to peak load, whereas unprotected specimens showed disordered fluctuations. The mutation point of energy concentration ρ for silane-protected specimens occurred at 0.83 σc, representing a 9.2% threshold elevation compared to 0.76 σc for unprotected specimens, confirming delayed damage accumulation in protected specimens. MF-DFA revealed narrowing spectrum width () in unprotected specimens, indicating reduced heterogeneity in AE signals, while protected specimens maintained significant multifractal divergence. peak localization revealed that weak AE signals dominated during early loading stages in both groups, with crack evolution primarily involving sliding and friction. During the mid-late elastic phase, crack propagation became the predominant failure mode. Experimental evidence confirms the engineering significance of silane protection in extending service life of concrete structures in sulfate environments. The proposed multi-parameter AE diagnostic methodology provides quantitative criteria for the safety monitoring of protected concrete structures in sulfate-rich conditions. - Open Access
- 27 November 2023
- Published by MDPI AG in Fractal and Fractional
- Vol. 7 (12) , 842
Multifractal Characteristics of Smooth Blasting Overbreak in Extra-Long Hard Rock Tunnel
With the development of infrastructure construction in mountainous areas, the number of new extra-long tunnels is increasing. However, these tunnels often face the challenge of complex and variable surrounding rock grades, resulting in a large number of overbreak and underbreak due to the untimely adjustment of smooth blasting parameters. This study focuses on the optimization of the peripheral hole charging structure and blasting parameters for extra-long hard rock tunnels, aiming to improve the effectiveness of smooth blasting technology. The results of this study demonstrate a significant improvement in the effect of smooth blasting after implementing bidirectional polymerization blasting in the tunnel. A comparison between the bidirectional shaped charge and spaced decoupled charge blasting reveals that the former yields better results. To obtain accurate data on the tunnel section profile during excavation, a laser cross-section meter is used for measurement. Furthermore, this study quantitatively compares the optimization effect of smooth blasting parameters. The multifractal characteristics of the tunnel profile overbreak point sequences are analyzed under different smooth blasting schemes using the multifractal detrended fluctuation analysis (MF-DFA) method. It is found that both the spaced decoupled charge and the bidirectional shaped charge blasting exhibit multifractal features in the overbreak measurement point sequences. The calculation results of the multifractal features of the tunnel profile under different smooth blasting plans are in line with the actual situation.
- 27 November 2023
- Published by MDPI AG in Fractal and Fractional
- Vol. 7 (12) , 842
Open AccessMultifractal Characteristics of Smooth Blasting Overbreak in Extra-Long Hard Rock Tunnel
With the development of infrastructure construction in mountainous areas, the number of new extra-long tunnels is increasing. However, these tunnels often face the challenge of complex and variable surrounding rock grades, resulting in a large number of overbreak and underbreak due to the untimely adjustment of smooth blasting parameters. This study focuses on the optimization of the peripheral hole charging structure and blasting parameters for extra-long hard rock tunnels, aiming to improve the effectiveness of smooth blasting technology. The results of this study demonstrate a significant improvement in the effect of smooth blasting after implementing bidirectional polymerization blasting in the tunnel. A comparison between the bidirectional shaped charge and spaced decoupled charge blasting reveals that the former yields better results. To obtain accurate data on the tunnel section profile during excavation, a laser cross-section meter is used for measurement. Furthermore, this study quantitatively compares the optimization effect of smooth blasting parameters. The multifractal characteristics of the tunnel profile overbreak point sequences are analyzed under different smooth blasting schemes using the multifractal detrended fluctuation analysis (MF-DFA) method. It is found that both the spaced decoupled charge and the bidirectional shaped charge blasting exhibit multifractal features in the overbreak measurement point sequences. The calculation results of the multifractal features of the tunnel profile under different smooth blasting plans are in line with the actual situation.
- Open Access
Comprehensive Testing of Sulfate Erosion Damage of Concrete Structures and Analysis of Silane Coating Protection Effect
In order to study the protection performance of silane coating on in-service concrete structures in a sulfate environment, we collect concrete samples in the field to simulate the concrete erosion process by accelerated erosion with wetting–drying cycles. We place the samples into protected, exposed and control groups corresponding to a corrosive environment with silane protection, corrosive environment without protection and general environment for three different service conditions. A combination of ultrasonic velocimetry, CT (Computed Tomography) scan imaging, NMR (Nuclear Magnetic Resonance) pore structure analysis, strength testing and other methods are used to analyze the strength, ultrasonic wave velocity, pore structure and other characteristics of the specimens during sulfate erosion. Based on the test results, the protective effect of silane coating on concrete structures under sulfate attack is quantitatively analyzed, and an index for judging the damage rate of specimens is proposed to quantitatively analyze the protective effect of silane coating. The research results show that the damage of the concrete structure under silane protection in a sulfate-attack environment can be reduced by more than 50%; its integrity damage index and strength damage index are easily affected by the location of local defects, which leads to a decrease in the protection efficiency of the surface silane coating.
Open AccessComprehensive Testing of Sulfate Erosion Damage of Concrete Structures and Analysis of Silane Coating Protection Effect
In order to study the protection performance of silane coating on in-service concrete structures in a sulfate environment, we collect concrete samples in the field to simulate the concrete erosion process by accelerated erosion with wetting–drying cycles. We place the samples into protected, exposed and control groups corresponding to a corrosive environment with silane protection, corrosive environment without protection and general environment for three different service conditions. A combination of ultrasonic velocimetry, CT (Computed Tomography) scan imaging, NMR (Nuclear Magnetic Resonance) pore structure analysis, strength testing and other methods are used to analyze the strength, ultrasonic wave velocity, pore structure and other characteristics of the specimens during sulfate erosion. Based on the test results, the protective effect of silane coating on concrete structures under sulfate attack is quantitatively analyzed, and an index for judging the damage rate of specimens is proposed to quantitatively analyze the protective effect of silane coating. The research results show that the damage of the concrete structure under silane protection in a sulfate-attack environment can be reduced by more than 50%; its integrity damage index and strength damage index are easily affected by the location of local defects, which leads to a decrease in the protection efficiency of the surface silane coating.
- Open Access
Orthogonal Experimental Study on Concrete Properties of Machine-Made Tuff Sand
Machine-made sand instead of natural sand has become an inevitable choice for the sustainable development of the concrete industry. Orthogonal experiment and grey correlation analysis were used to investigate the performance of machine-made tuff sand concrete. The optimal concrete mix ratio of machine-made sand was obtained by orthogonal test and its working performance was verified. Grey correlation analysis was applied to compare the factors affecting the mechanical properties of the machine-made sand concrete. The test results show that the sand rate has the greatest degree of influence on slump and slump expansion. The mineral admixture has the greatest effect on the 7-day compressive strength of the concrete. Additionally, the water–cement ratio has the greatest influence on the 28-day compressive strength. The mechanical and working properties of the machine-made sand concrete reach the optimum condition when the mineral admixture is 20%, the sand rate is 46%, the stone powder content is 10% and the water–cement ratio is 0.30. Comparing different fine aggregate concretes of similar quality, we conclude that the mechanical and working properties of tuff sand concrete and limestone sand concrete and river sand concrete are similar. The compressive strengths of the mechanism concrete show the greatest correlation with roughness and the least correlation with stone powder content. The stone powder content has almost no effect on the compressive strength of concrete when the stone powder content does not exceed a certain range. The results of the study point out the direction for the quality control of concrete with machine-made sand.
Open AccessOrthogonal Experimental Study on Concrete Properties of Machine-Made Tuff Sand
Machine-made sand instead of natural sand has become an inevitable choice for the sustainable development of the concrete industry. Orthogonal experiment and grey correlation analysis were used to investigate the performance of machine-made tuff sand concrete. The optimal concrete mix ratio of machine-made sand was obtained by orthogonal test and its working performance was verified. Grey correlation analysis was applied to compare the factors affecting the mechanical properties of the machine-made sand concrete. The test results show that the sand rate has the greatest degree of influence on slump and slump expansion. The mineral admixture has the greatest effect on the 7-day compressive strength of the concrete. Additionally, the water–cement ratio has the greatest influence on the 28-day compressive strength. The mechanical and working properties of the machine-made sand concrete reach the optimum condition when the mineral admixture is 20%, the sand rate is 46%, the stone powder content is 10% and the water–cement ratio is 0.30. Comparing different fine aggregate concretes of similar quality, we conclude that the mechanical and working properties of tuff sand concrete and limestone sand concrete and river sand concrete are similar. The compressive strengths of the mechanism concrete show the greatest correlation with roughness and the least correlation with stone powder content. The stone powder content has almost no effect on the compressive strength of concrete when the stone powder content does not exceed a certain range. The results of the study point out the direction for the quality control of concrete with machine-made sand.
- Open Access
Evaluation of Corrosion Damage in Sulfate-Attacked Concrete by CT, Ultrasonic Pulse Velocity Testing and AHP Methods
Coarse aggregate in concrete is basically free from sulfate corrosion. If the influence of the coarse aggregate in the concrete is not eliminated, the change amount of the concrete ultrasonic pulse velocity value is directly used to evaluate the damage degree of sulfate corrosion in the concrete, and the results are often inaccurate. This paper presents an evaluation method of corrosion damage for the sulfate-attacked concrete by CT, ultrasonic velocity testing and AHP methods. CT was used to extract the coarse aggregate information in the specimen, and the proportion of coarse aggregate on the ultrasonic test line was calculated based on CT image analysis. Then, the correction value of ultrasonic pulse velocity (UPV) of the concrete structure was calculated, and the sulfate corrosion degree of concrete structure was evaluated using the analytic hierarchy process (AHP). The results show that the evaluation method proposed in this paper could more accurately evaluate the corrosion damage in the sulfate-attacked concrete structures, and the evaluation results were more in line with reality.
Open AccessEvaluation of Corrosion Damage in Sulfate-Attacked Concrete by CT, Ultrasonic Pulse Velocity Testing and AHP Methods
Coarse aggregate in concrete is basically free from sulfate corrosion. If the influence of the coarse aggregate in the concrete is not eliminated, the change amount of the concrete ultrasonic pulse velocity value is directly used to evaluate the damage degree of sulfate corrosion in the concrete, and the results are often inaccurate. This paper presents an evaluation method of corrosion damage for the sulfate-attacked concrete by CT, ultrasonic velocity testing and AHP methods. CT was used to extract the coarse aggregate information in the specimen, and the proportion of coarse aggregate on the ultrasonic test line was calculated based on CT image analysis. Then, the correction value of ultrasonic pulse velocity (UPV) of the concrete structure was calculated, and the sulfate corrosion degree of concrete structure was evaluated using the analytic hierarchy process (AHP). The results show that the evaluation method proposed in this paper could more accurately evaluate the corrosion damage in the sulfate-attacked concrete structures, and the evaluation results were more in line with reality.
- Open Access
Analysis and Prediction of Sulfate Erosion Damage of Concrete in Service Tunnel Based on ARIMA Model
Sulfate erosion is a major cause of concrete durability deteriorations, especially for the service tunnels that suffer sulfate erosion for a long time. Accurately predicting the concrete damage failure under sulfate erosion has been a challenging problem in the evaluation and maintenance of concrete structures. Here we design the dry–wet cycle test of service tunnel concrete under sulfate erosion and analyze the Elastic relative dynamic modulus (Erd) and mass under 35 times cycle periods. Then we develop an autoregressive integrated moving average (ARIMA) prediction model linking damage failure to Erd and mass. The results show that the deterioration of concrete first increased and then decreased with an extension of the dry–wet cycle period. Moreover, based on a finite set of training data, the proposed prediction approach shows high accuracy for the changes of concrete damage failure parameters in or out of the training dataset. The ARIMA method is proven to be feasible and efficient for predicting the concrete damage failure of service tunnels under sulfate erosion for a long time.
Open AccessAnalysis and Prediction of Sulfate Erosion Damage of Concrete in Service Tunnel Based on ARIMA Model
Sulfate erosion is a major cause of concrete durability deteriorations, especially for the service tunnels that suffer sulfate erosion for a long time. Accurately predicting the concrete damage failure under sulfate erosion has been a challenging problem in the evaluation and maintenance of concrete structures. Here we design the dry–wet cycle test of service tunnel concrete under sulfate erosion and analyze the Elastic relative dynamic modulus (Erd) and mass under 35 times cycle periods. Then we develop an autoregressive integrated moving average (ARIMA) prediction model linking damage failure to Erd and mass. The results show that the deterioration of concrete first increased and then decreased with an extension of the dry–wet cycle period. Moreover, based on a finite set of training data, the proposed prediction approach shows high accuracy for the changes of concrete damage failure parameters in or out of the training dataset. The ARIMA method is proven to be feasible and efficient for predicting the concrete damage failure of service tunnels under sulfate erosion for a long time.
- Open Access
Evaluation of the Uniformity of Protective Coatings on Concrete Structure Surfaces Based on Cluster Analysis
With the continuous development of urbanization and industrialization in the world, concrete is widely used in various engineering constructions as an engineering material. However, the consequent problem of durability of concrete structures is also becoming increasingly prominent. As an important additional measure, a protective coating can effectively improve the durability of concrete performance. Moreover, the uniformity of the concrete surface coating will directly affect its protective effect. Therefore, we propose a nondestructive inspection and evaluation method of coating uniformity based on infrared imaging and cluster analysis for concrete surface coating uniformity detection and evaluation. Based on the obtained infrared images, a series of processing and analysis of the images were carried out using MATLAB software to obtain the characteristics of the infrared images of the concrete surface. Finally, by extracting the temperature distribution data of the pixel points on the concrete surface, an evaluation method of concrete surface coating uniformity based on a combination of cluster analysis and hierarchical analysis was established. The evaluation results show that the determination results obtained by this method are consistent with the actual situation. This study has a positive contribution to the testing of concrete surface coating uniformity and its evaluation.
Open AccessEvaluation of the Uniformity of Protective Coatings on Concrete Structure Surfaces Based on Cluster Analysis
With the continuous development of urbanization and industrialization in the world, concrete is widely used in various engineering constructions as an engineering material. However, the consequent problem of durability of concrete structures is also becoming increasingly prominent. As an important additional measure, a protective coating can effectively improve the durability of concrete performance. Moreover, the uniformity of the concrete surface coating will directly affect its protective effect. Therefore, we propose a nondestructive inspection and evaluation method of coating uniformity based on infrared imaging and cluster analysis for concrete surface coating uniformity detection and evaluation. Based on the obtained infrared images, a series of processing and analysis of the images were carried out using MATLAB software to obtain the characteristics of the infrared images of the concrete surface. Finally, by extracting the temperature distribution data of the pixel points on the concrete surface, an evaluation method of concrete surface coating uniformity based on a combination of cluster analysis and hierarchical analysis was established. The evaluation results show that the determination results obtained by this method are consistent with the actual situation. This study has a positive contribution to the testing of concrete surface coating uniformity and its evaluation.
- Open Access
- 30 September 2020
- Published by MDPI AG in Preprints.org
Enterprise Work Safety Standardization Optimization Mode on VSM in China
The work safety standardization of enterprises based on the traditional work safety theory has played a significant role in reducing the number of accidents and improving work safety to some extent in China. However, some problems are coming with the work safety standardization of enterprises developing constantly in China. On the one hand, it is not combined with the actual situation of the enterprise, lacking pertinence and specificity, these defects resulted that it is not integrated with original safety production management system of enterprise and make it difficult to carry out. On the other hand, there is a lack of systematic management methods for the work safety management system of enterprise, most of enterprises only pay attention to the inspection result rather than the process control. This means after the check of the government, many enterprises will relax to carry out the system. This paper puts forward a new method for optimizing the standardization management mode of work safety based on the Viable System Model(VSM), which can solve the defects of work safety standardization of enterprises management system. An optimization model of work safety standardization based on VSM was construct for explaining the process optimization and control of work safety standardization management. It can improve the connectivity between the enterprise and the government. The conclusion of this paper can provide reference for achieving the development and optimization of work safety standardization of enterprises in China.
- 30 September 2020
- Published by MDPI AG in Preprints.org
Open AccessEnterprise Work Safety Standardization Optimization Mode on VSM in China
The work safety standardization of enterprises based on the traditional work safety theory has played a significant role in reducing the number of accidents and improving work safety to some extent in China. However, some problems are coming with the work safety standardization of enterprises developing constantly in China. On the one hand, it is not combined with the actual situation of the enterprise, lacking pertinence and specificity, these defects resulted that it is not integrated with original safety production management system of enterprise and make it difficult to carry out. On the other hand, there is a lack of systematic management methods for the work safety management system of enterprise, most of enterprises only pay attention to the inspection result rather than the process control. This means after the check of the government, many enterprises will relax to carry out the system. This paper puts forward a new method for optimizing the standardization management mode of work safety based on the Viable System Model(VSM), which can solve the defects of work safety standardization of enterprises management system. An optimization model of work safety standardization based on VSM was construct for explaining the process optimization and control of work safety standardization management. It can improve the connectivity between the enterprise and the government. The conclusion of this paper can provide reference for achieving the development and optimization of work safety standardization of enterprises in China.