Muhammad Roman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Interests
Muhammad Roman has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Jie Huang
Missouri University of Science and Technology
7 shared publications - Rex E. Gerald
Department of Electrical and Computer Engineering, Missouri University of Science and Technology, Rolla, MO, USA
5 shared publications - Ronald J. O’malley
Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO, USA
5 shared publications - Laura Bartlett
Department of Material Science and Engineering, Missouri University of Science and Technology, Rolla, MO, USA
4 shared publications - Bohong Zhang
Department of Electrical and Computer Engineering, Missouri University of Science and Technology, Rolla, MO, USA
2 shared publications - Chen Zhu
Missouri University of Science and Technology
2 shared publications
Latest Publications
- 13 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-12
Distributed Temperature Sensing in the Spray-Cooled Shell of a 150-Ton DC Electric Arc Furnace Using Brillouin Optical Fiber Technology
This paper presents the deployment and validation of a Brillouin - distributed temperature sensing (DTS) system for real-time thermal monitoring of the spray-cooled upper shell of a 150-ton direct current Electric Arc Furnace (DC EAF) at Big River Steel Plant, Osceola, AR, USA. A four-channel Brillouin DTS system from OZ Optics was employed, with one active channel instrumented using an in-house-fabricated Brillouin scattering-depressed single-mode optical fiber (SMF28e+). The 60 m optical fiber sensor was fabricated, with 20 m allocated for thermal measurement and 40 m used as lead-in fiber to isolate the interrogator from the furnace environment. The fiber was nested in stainless steel (SS) tubing and bonded to the hot-face surface of the shell using thermally conductive epoxy. The system captured transient thermal events including burner activation and process-induced heating over multiple furnace cycles. DTS-acquired data were validated against resistance temperature detector (RTD) measurements, confirming consistent thermal trends and system accuracy. Prior to the industrial deployment, several mock-up tests were conducted. Laboratory calibration demonstrated a linear Brillouin frequency shift with temperature, with a sensitivity of approximately 1.19 °C/MHz up to 515 °C and R2 = 0.9988. Additional mock-up trials confirmed spatial resolution between 0.5 m and 1 m, with transmission and reflection spectra showing hotspot detection over sensing lengths up to 130 m. An averaging spatial step of 0.04 m was used, and acquisition sweep time was set to 1 min with a 10 MHz frequency step size and 10,000 averages. Monitoring the spray-cooled shell is critical in EAF operations due to its exposure to high thermal loads and susceptibility to localized overheating. Real-time hotspot detection and localization support proactive maintenance, reduce the risk of shell failure, and improve energy efficiency and operational safety. These findings underscore the potential of Brillouin - DTS systems to enable intelligent process control and predictive maintenance in next-generation steelmaking facilities.
- 13 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-12
Distributed Temperature Sensing in the Spray-Cooled Shell of a 150-Ton DC Electric Arc Furnace Using Brillouin Optical Fiber Technology
This paper presents the deployment and validation of a Brillouin - distributed temperature sensing (DTS) system for real-time thermal monitoring of the spray-cooled upper shell of a 150-ton direct current Electric Arc Furnace (DC EAF) at Big River Steel Plant, Osceola, AR, USA. A four-channel Brillouin DTS system from OZ Optics was employed, with one active channel instrumented using an in-house-fabricated Brillouin scattering-depressed single-mode optical fiber (SMF28e+). The 60 m optical fiber sensor was fabricated, with 20 m allocated for thermal measurement and 40 m used as lead-in fiber to isolate the interrogator from the furnace environment. The fiber was nested in stainless steel (SS) tubing and bonded to the hot-face surface of the shell using thermally conductive epoxy. The system captured transient thermal events including burner activation and process-induced heating over multiple furnace cycles. DTS-acquired data were validated against resistance temperature detector (RTD) measurements, confirming consistent thermal trends and system accuracy. Prior to the industrial deployment, several mock-up tests were conducted. Laboratory calibration demonstrated a linear Brillouin frequency shift with temperature, with a sensitivity of approximately 1.19 °C/MHz up to 515 °C and R2 = 0.9988. Additional mock-up trials confirmed spatial resolution between 0.5 m and 1 m, with transmission and reflection spectra showing hotspot detection over sensing lengths up to 130 m. An averaging spatial step of 0.04 m was used, and acquisition sweep time was set to 1 min with a 10 MHz frequency step size and 10,000 averages. Monitoring the spray-cooled shell is critical in EAF operations due to its exposure to high thermal loads and susceptibility to localized overheating. Real-time hotspot detection and localization support proactive maintenance, reduce the risk of shell failure, and improve energy efficiency and operational safety. These findings underscore the potential of Brillouin - DTS systems to enable intelligent process control and predictive maintenance in next-generation steelmaking facilities.
- Open Access
- 1 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-12
Advancing Aluminum Casting Optimization With Real-Time Temperature and Gap Measurements Using Optical Fiber Sensors at the Metal-Mold Interface
Accurate measurement of interfacial heat transfer during casting solidification is crucial for optimizing metal solidification processes. The gap between the mold wall and casting surface plays a significant role in heat transfer and cooling rates. In this study, two innovative fiber-optic sensors are employed to measure real-time mold gaps and thermal profiles during the solidification of A356 aluminum in a permanent mold casting. The experimental setup consists of a specially designed mold system made of unheated, uncoated tool steel, which facilitates easy installation of the fiber-optic sensors. An Extrinsic Fabry-Perot interferometric (EFPI) sensor is utilized to monitor the evolving gap between the mold wall and casting surface. This method relies on the unique concept of using molten metal as the second reflection interface for gap measurements. The EFPI gap measurements exhibit high accuracy and precision, with a maximum error of only 2 μm when compared to physical measurements. Simultaneously, a stainless steel-encased fiber utilizing the Rayleigh backscattering (RBS) technique is deployed across the mold wall and cavity to achieve real-time temperature measurements with a spatial resolution of 0.65 mm. The study demonstrates that leveraging high-resolution temperature profiles and gap evolution measurements enhances understanding of heat transfer dynamics at the mold-metal interface, particularly valuable for complex-shaped castings and continuously cast metals. Additionally, the ability to measure the cast shape exiting a continuous casting mold during operation presents a novel tool for real-time product quality monitoring and process safety enhancement by detecting conditions that may lead to slab cracking and breakouts.
- 1 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-12
Open AccessAdvancing Aluminum Casting Optimization With Real-Time Temperature and Gap Measurements Using Optical Fiber Sensors at the Metal-Mold Interface
Accurate measurement of interfacial heat transfer during casting solidification is crucial for optimizing metal solidification processes. The gap between the mold wall and casting surface plays a significant role in heat transfer and cooling rates. In this study, two innovative fiber-optic sensors are employed to measure real-time mold gaps and thermal profiles during the solidification of A356 aluminum in a permanent mold casting. The experimental setup consists of a specially designed mold system made of unheated, uncoated tool steel, which facilitates easy installation of the fiber-optic sensors. An Extrinsic Fabry-Perot interferometric (EFPI) sensor is utilized to monitor the evolving gap between the mold wall and casting surface. This method relies on the unique concept of using molten metal as the second reflection interface for gap measurements. The EFPI gap measurements exhibit high accuracy and precision, with a maximum error of only 2 μm when compared to physical measurements. Simultaneously, a stainless steel-encased fiber utilizing the Rayleigh backscattering (RBS) technique is deployed across the mold wall and cavity to achieve real-time temperature measurements with a spatial resolution of 0.65 mm. The study demonstrates that leveraging high-resolution temperature profiles and gap evolution measurements enhances understanding of heat transfer dynamics at the mold-metal interface, particularly valuable for complex-shaped castings and continuously cast metals. Additionally, the ability to measure the cast shape exiting a continuous casting mold during operation presents a novel tool for real-time product quality monitoring and process safety enhancement by detecting conditions that may lead to slab cracking and breakouts.
- 28 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-11
Temperature Monitoring in the Refractory Lining of a Continuous Casting Tundish Using Distributed Optical Fiber Sensors
This paper explores the prospects of using spatially distributed optical fiber temperature sensors based on Rayleigh OFDR (optical frequency domain reflectometry) technology in the continuous casting of molten steel. The measurement capability of the optical fiber sensors in a simulated steelmaking environment was demonstrated using a mock refractory-lined tundish, which was fabricated in-house. Single-mode optical fibers, contained in protective stainless-steel tubing, were embedded in the refractory lining of the mock tundish. The instrumented tundish was preheated up to a temperature of 960 °C (recorded at the surface of the working lining) before the molten steel pour. A low-alloy steel (AISI 4140 grade) was melted in a 200 lb (90.7 kg) coreless induction furnace and was poured into the instrumented preheated tundish. The embedded optical fiber sensors were used to measure the temperature distribution in the castable lining during the preheating process of the tundish and during its contact with molten steel. Temperatures were metered with a spatial resolution of 0.65 mm along the embedded optical fibers. The measurements were recorded with an update rate of 1 Hz. The maximum temperature recorded by the optical fiber sensors in the castable lining after the steel pour was 591 °C. The spatially continuous optical fiber sensors provided useful information on thermal gradients in the castable lining. Real-time monitoring of spatially distributed thermal profiles in the refractory lining can improve superheat control, reduce energy losses, detect refractory wear, and improve the quality of the cast.
- 28 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 72 (00189456) , 1-11
Temperature Monitoring in the Refractory Lining of a Continuous Casting Tundish Using Distributed Optical Fiber Sensors
This paper explores the prospects of using spatially distributed optical fiber temperature sensors based on Rayleigh OFDR (optical frequency domain reflectometry) technology in the continuous casting of molten steel. The measurement capability of the optical fiber sensors in a simulated steelmaking environment was demonstrated using a mock refractory-lined tundish, which was fabricated in-house. Single-mode optical fibers, contained in protective stainless-steel tubing, were embedded in the refractory lining of the mock tundish. The instrumented tundish was preheated up to a temperature of 960 °C (recorded at the surface of the working lining) before the molten steel pour. A low-alloy steel (AISI 4140 grade) was melted in a 200 lb (90.7 kg) coreless induction furnace and was poured into the instrumented preheated tundish. The embedded optical fiber sensors were used to measure the temperature distribution in the castable lining during the preheating process of the tundish and during its contact with molten steel. Temperatures were metered with a spatial resolution of 0.65 mm along the embedded optical fibers. The measurements were recorded with an update rate of 1 Hz. The maximum temperature recorded by the optical fiber sensors in the castable lining after the steel pour was 591 °C. The spatially continuous optical fiber sensors provided useful information on thermal gradients in the castable lining. Real-time monitoring of spatially distributed thermal profiles in the refractory lining can improve superheat control, reduce energy losses, detect refractory wear, and improve the quality of the cast.
- 19 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-10
Thermal Mapping of Metal Casting Mold Using High-Resolution Distributed Fiber-Optic Sensors
This article reports a technique to embed optical fiber into a copper mold plate for generating high-density thermal maps of the mold during the process of metal casting. The temperature measurements were based on acquiring and interpreting Rayleigh backscattering (RBS) signals from embedded fiber, using the interrogation technique of optical frequency domain reflectometry (OFDR). The instrumented mold plate was used to perform a cast-iron dip test and a steel dip test in a 200 lb induction furnace. The maximum temperatures recorded by the embedded fiber-optic sensors were 469 °C and 388 °C in the cast-iron and steel dip tests, respectively. The closely spaced and rapidly fluctuating temperature features that were imparted to the mold wall during solidification were successfully mapped with a high spatial resolution (0.65 mm) and a fast measurement rate (25 Hz) using a commercial OFDR interrogator (LUNA ODiSI 6108). Moreover, the thickness of the solidified steel shell was measured, and a thickness map of the shell was generated. A good correlation was observed between the thickness of the solidified shell and the temperature of the mold, as regions with higher and lower temperatures in the thermal profile of the mold corresponded to thicker and thinner areas on the shell, respectively. The dip testing experiments demonstrate that RBS-based fiber-optic sensing is a feasible and effective method for generating information-rich thermal maps of caster molds. The information obtained from thermal maps can be useful for improving the quality of the metal and productivity of the metal casting process.
- 19 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 70 (00189456) , 1-10
Thermal Mapping of Metal Casting Mold Using High-Resolution Distributed Fiber-Optic Sensors
This article reports a technique to embed optical fiber into a copper mold plate for generating high-density thermal maps of the mold during the process of metal casting. The temperature measurements were based on acquiring and interpreting Rayleigh backscattering (RBS) signals from embedded fiber, using the interrogation technique of optical frequency domain reflectometry (OFDR). The instrumented mold plate was used to perform a cast-iron dip test and a steel dip test in a 200 lb induction furnace. The maximum temperatures recorded by the embedded fiber-optic sensors were 469 °C and 388 °C in the cast-iron and steel dip tests, respectively. The closely spaced and rapidly fluctuating temperature features that were imparted to the mold wall during solidification were successfully mapped with a high spatial resolution (0.65 mm) and a fast measurement rate (25 Hz) using a commercial OFDR interrogator (LUNA ODiSI 6108). Moreover, the thickness of the solidified steel shell was measured, and a thickness map of the shell was generated. A good correlation was observed between the thickness of the solidified shell and the temperature of the mold, as regions with higher and lower temperatures in the thermal profile of the mold corresponded to thicker and thinner areas on the shell, respectively. The dip testing experiments demonstrate that RBS-based fiber-optic sensing is a feasible and effective method for generating information-rich thermal maps of caster molds. The information obtained from thermal maps can be useful for improving the quality of the metal and productivity of the metal casting process.
- 8 September 2021
- Published by Wiley in Steel Research International
- Vol. 93 (1)
Shell Measurements and Mold Thermal Mapping Approach to Characterize Steel Shell Formation in Peritectic Grade Steels
Herein, the prospects of detecting peritectic behavior in carbon steels (Fe–C) using solidified shell thickness measurements and real‐time mold thermal maps are investigated. Irregular steel shell thickness and localized shell thinning are negative conditions associated with the peritectic transformation in many steel grades. Detailed three dimensional (3D) thickness maps are generated to directly contrast peritectic from nonperitectic solidification features using a laboratory dip test. Characterization of the steel shell also includes measurement of 3D shell surface deviations from a nominally flat surface. The unevenness parameter, which is calculated using the coefficient of variation in shell thickness as a function of the carbon content in the steel, clearly peaks around 0.14%C. A distributed fiber‐optic sensor, embedded 1 mm from the working face of a 100 × 55 × 12 mm3 thick copper chill block, has been used to obtain real‐time mold thermal maps of the solidification event during immersion of the block into molten steel. A programmable drive is used to control the motion of the chill block during immersion into a steel bath to minimize variability in immersion speed, position, and time. The thermal mapping measurements are well correlated with the shell profile measurements.
- 8 September 2021
- Published by Wiley in Steel Research International
- Vol. 93 (1)
Shell Measurements and Mold Thermal Mapping Approach to Characterize Steel Shell Formation in Peritectic Grade Steels
Herein, the prospects of detecting peritectic behavior in carbon steels (Fe–C) using solidified shell thickness measurements and real‐time mold thermal maps are investigated. Irregular steel shell thickness and localized shell thinning are negative conditions associated with the peritectic transformation in many steel grades. Detailed three dimensional (3D) thickness maps are generated to directly contrast peritectic from nonperitectic solidification features using a laboratory dip test. Characterization of the steel shell also includes measurement of 3D shell surface deviations from a nominally flat surface. The unevenness parameter, which is calculated using the coefficient of variation in shell thickness as a function of the carbon content in the steel, clearly peaks around 0.14%C. A distributed fiber‐optic sensor, embedded 1 mm from the working face of a 100 × 55 × 12 mm3 thick copper chill block, has been used to obtain real‐time mold thermal maps of the solidification event during immersion of the block into molten steel. A programmable drive is used to control the motion of the chill block during immersion into a steel bath to minimize variability in immersion speed, position, and time. The thermal mapping measurements are well correlated with the shell profile measurements.
- Open Access
- 15 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 32627-32633
Microsphere Photolithography Patterned Nanohole Array on an Optical Fiber
Microsphere Photolithography (MPL) is a nanopatterning technique that utilizes a self-assembled monolayer of microspheres as an optical element to focus incident radiation inside a layer of photoresist. The microspheres produces a sub-diffraction limited photonic-jet on the opposite side of each microsphere from the illumination. When combined with pattern transfer techniques such as etching/lift-off, MPL provides a versatile, low-cost fabrication method for producing hexagonal close-packed metasurfaces. This article investigates the MPL process for creating refractive index (RI) sensors on the cleaved tips of optical fiber. The resonant wavelength of metal elements on the surface is dependent on the local dielectric environment and allows the refractive index of an analyte to be resolved spectrally. A numerical study of hole arrays defined in metal films shows that the waveguide mode provides good sensitivity to the analyte refractive index. This can be readily tuned by adjusting the MPL exposure and the simulation results guide the fabrication of a defect tolerant refractive index sensor on the tip of a fiber tip with a sensitivity of 613 nm/RIU. The conformal nature of the microsphere monolayer simplifies the fabrication process and provides a viable alternative to direct-write techniques such as Focused Ion Beam (FIB) milling.
- 15 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 32627-32633
Open AccessMicrosphere Photolithography Patterned Nanohole Array on an Optical Fiber
Microsphere Photolithography (MPL) is a nanopatterning technique that utilizes a self-assembled monolayer of microspheres as an optical element to focus incident radiation inside a layer of photoresist. The microspheres produces a sub-diffraction limited photonic-jet on the opposite side of each microsphere from the illumination. When combined with pattern transfer techniques such as etching/lift-off, MPL provides a versatile, low-cost fabrication method for producing hexagonal close-packed metasurfaces. This article investigates the MPL process for creating refractive index (RI) sensors on the cleaved tips of optical fiber. The resonant wavelength of metal elements on the surface is dependent on the local dielectric environment and allows the refractive index of an analyte to be resolved spectrally. A numerical study of hole arrays defined in metal films shows that the waveguide mode provides good sensitivity to the analyte refractive index. This can be readily tuned by adjusting the MPL exposure and the simulation results guide the fabrication of a defect tolerant refractive index sensor on the tip of a fiber tip with a sensitivity of 613 nm/RIU. The conformal nature of the microsphere monolayer simplifies the fabrication process and provides a viable alternative to direct-write techniques such as Focused Ion Beam (FIB) milling.
- 11 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (6) , 7672-7680
Distributed Fiber-Optic Sensing With Low Bending Loss Based on Thin-Core Fiber
This paper presents a thin-core high-numerical aperture (TC-HNA) optical fiber with low macrobending loss for Rayleigh backscattering-based (RBS-based) temperature and strain measurements. The standard single-mode optical fiber (SMF), commonly used in RBS-based sensing, has low macrobending loss-resistance, making the fiber less suited for sensing applications that require sharp bending of the fiber under test. The TC-HNA fiber, on the other hand, offers high macrobending loss-resistance. Experiments were designed and conducted to demonstrate the reliability of a TC-HNA fiber for RBS-based temperature and strain measurements. The macrobending losses in a standard SMF and a TC-HNA fiber were compared in many experiments conducted with different bending radii ranging from 12.5 mm down to 0.9 mm. The RBS signal for a standard SMF, with a single turn of a 5 mm bending radius, degraded severely, exhibiting a 75% drop (6 dB) in signal power. Notably, the RBS signal for a similar test configuration of a TC-HNA fiber did not exhibit any observable loss. We demonstrated that a TC-HNA fiber could be used for RBS-based measurements with a single turn of ~1 mm bending radius. Moreover, an experiment was conducted to demonstrate the spatial thermal mapping capability of the TC-HNA fiber configured with multiple tight bends with radii in the range ~2-3 mm. The high macrobending loss-resistance of the TC-HNA fiber could extend the range of applications for RBS-based measurements to compact structures, such as batteries, robotic fingers, and printed circuit boards, where sharp bending of the test optical fiber is unavoidable.
- 11 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (6) , 7672-7680
Distributed Fiber-Optic Sensing With Low Bending Loss Based on Thin-Core Fiber
This paper presents a thin-core high-numerical aperture (TC-HNA) optical fiber with low macrobending loss for Rayleigh backscattering-based (RBS-based) temperature and strain measurements. The standard single-mode optical fiber (SMF), commonly used in RBS-based sensing, has low macrobending loss-resistance, making the fiber less suited for sensing applications that require sharp bending of the fiber under test. The TC-HNA fiber, on the other hand, offers high macrobending loss-resistance. Experiments were designed and conducted to demonstrate the reliability of a TC-HNA fiber for RBS-based temperature and strain measurements. The macrobending losses in a standard SMF and a TC-HNA fiber were compared in many experiments conducted with different bending radii ranging from 12.5 mm down to 0.9 mm. The RBS signal for a standard SMF, with a single turn of a 5 mm bending radius, degraded severely, exhibiting a 75% drop (6 dB) in signal power. Notably, the RBS signal for a similar test configuration of a TC-HNA fiber did not exhibit any observable loss. We demonstrated that a TC-HNA fiber could be used for RBS-based measurements with a single turn of ~1 mm bending radius. Moreover, an experiment was conducted to demonstrate the spatial thermal mapping capability of the TC-HNA fiber configured with multiple tight bends with radii in the range ~2-3 mm. The high macrobending loss-resistance of the TC-HNA fiber could extend the range of applications for RBS-based measurements to compact structures, such as batteries, robotic fingers, and printed circuit boards, where sharp bending of the test optical fiber is unavoidable.