Eline Vandecruys
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Eline Vandecruys has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Els Verstrynge
KU Leuven Leuven Belgium
9 shared publications - Charlotte Van Steen
Department of Civil Engineering, KU Leuven, Belgium
6 shared publications - Geert Lombaert
Structural Mechanics, Civil Engineering Department, KU Leuven
6 shared publications Els Verstrynge
Department of Civil Engineering, KU Leuven, Belgium
5 shared publications- Constantijn Martens
Department of Civil Engineering, Materials and Constructions Section KU Leuven Leuven Belgium
4 shared publications - Menno van de Velde
KU Leuven
3 shared publications
Latest Publications
- 4 July 2026
- Published by SAGE Publications in Structural Health Monitoring
Periodic acoustic emission monitoring of reinforced concrete beams under natural corrosion conditions
Reinforcement corrosion is a critical issue affecting structural integrity and service life of existing reinforced concrete (RC) structures. While acoustic emission (AE) monitoring provides early damage detection and localization, its application during slow natural corrosion processes and in noisy outdoor environments remains challenging. This study investigates the feasibility of periodic AE monitoring during natural chloride-induced corrosion of two pre-damaged RC beams stored outdoors. Two AE sensor types were evaluated under realistic environmental influences. A dedicated filtering approach was developed to distinguish damage-related AE signals from environmental noise. The results demonstrate that periodic AE monitoring can effectively track damage evolution and localize corrosion hotspots in both one dimensional and two dimensional. Furthermore, a previously developed methodology for estimating accelerated corrosion levels based on AE localization was successfully applied to natural corrosion, confirming its broader applicability. These findings highlight the potential of the AE technique for structural health monitoring of RC structures under field conditions.
- 4 July 2026
- Published by SAGE Publications in Structural Health Monitoring
Periodic acoustic emission monitoring of reinforced concrete beams under natural corrosion conditions
Reinforcement corrosion is a critical issue affecting structural integrity and service life of existing reinforced concrete (RC) structures. While acoustic emission (AE) monitoring provides early damage detection and localization, its application during slow natural corrosion processes and in noisy outdoor environments remains challenging. This study investigates the feasibility of periodic AE monitoring during natural chloride-induced corrosion of two pre-damaged RC beams stored outdoors. Two AE sensor types were evaluated under realistic environmental influences. A dedicated filtering approach was developed to distinguish damage-related AE signals from environmental noise. The results demonstrate that periodic AE monitoring can effectively track damage evolution and localize corrosion hotspots in both one dimensional and two dimensional. Furthermore, a previously developed methodology for estimating accelerated corrosion levels based on AE localization was successfully applied to natural corrosion, confirming its broader applicability. These findings highlight the potential of the AE technique for structural health monitoring of RC structures under field conditions.
- 2 August 2025
- Published by Wiley in Structural Concrete
- Vol. 27 (1) , 143-162
Reinforcement corrosion assessment through Bayesian parameter updating with spatially distributed inspection data
An accurate assessment of corrosion in reinforced concrete structures is crucial for predicting their remaining capacity. Hence, this research develops a Bayesian updating approach, utilizing spatially distributed inspection data, to enhance corrosion parameter predictions. The study focuses on two corrosion parameters, which represent both steel and concrete degradation: the corrosion level (CL) and reduced apparent concrete stiffness. Initial prior estimations of both corrosion parameters are based on corrosion initiation time and current density, as often employed in the literature and in practice. Thereafter, inspection data, including detailed crack measurements and acoustic emission sensing, are used to enhance the reliability of the parameter estimations, as quantified through Bayesian updating. The prior and posterior estimated corrosion parameters are incorporated in finite element model predictions of the structural capacity, which are compared with experimental test results to validate the updating approach and quantify the improved model accuracy. The results show that integrating inspection data improves corrosion parameter and structural capacity predictions, especially for structural elements with non‐uniform CLs. Moreover, the Bayesian framework allows for incorporation of uncertainties, ensuring robust corrosion assessments.
- 2 August 2025
- Published by Wiley in Structural Concrete
- Vol. 27 (1) , 143-162
Reinforcement corrosion assessment through Bayesian parameter updating with spatially distributed inspection data
An accurate assessment of corrosion in reinforced concrete structures is crucial for predicting their remaining capacity. Hence, this research develops a Bayesian updating approach, utilizing spatially distributed inspection data, to enhance corrosion parameter predictions. The study focuses on two corrosion parameters, which represent both steel and concrete degradation: the corrosion level (CL) and reduced apparent concrete stiffness. Initial prior estimations of both corrosion parameters are based on corrosion initiation time and current density, as often employed in the literature and in practice. Thereafter, inspection data, including detailed crack measurements and acoustic emission sensing, are used to enhance the reliability of the parameter estimations, as quantified through Bayesian updating. The prior and posterior estimated corrosion parameters are incorporated in finite element model predictions of the structural capacity, which are compared with experimental test results to validate the updating approach and quantify the improved model accuracy. The results show that integrating inspection data improves corrosion parameter and structural capacity predictions, especially for structural elements with non‐uniform CLs. Moreover, the Bayesian framework allows for incorporation of uncertainties, ensuring robust corrosion assessments.
- 15 October 2024
- Published by Wiley in Structural Concrete
- Vol. 26 (5) , 5578-5595
Corrosion level estimation in reinforced concrete beams by acoustic emission sensing and selective crack measurements
Accurate corrosion assessment plays an important role in ensuring structural safety of reinforced concrete (RC) structures. However, on‐site assessment of existing concrete structures presents many challenges, including high costs, limited inspection timeframes, and difficult accessibility. To facilitate inspection‐based corrosion assessment, this paper presents a novel approach by combining short‐term acoustic emission (AE) monitoring with selective crack width measurements for corrosion level (CL) assessment. AE sensing is a monitoring technique which can detect ongoing internal degradation mechanisms by analyzing ultrasonic waves emitted by the damage process. Yet, two major challenges arise on site: (1) practical limitations prevent continuous AE monitoring over the structure's entire lifetime and (2) AE can only generate relative results in the absence of reference measurements. This paper addresses both challenges to bridge the gap between laboratory experiments and on‐site monitoring of corroding RC structures. First, short periods of AE monitoring data are analyzed to investigate the potential of AE sensing over limited timeframes. Second, AE data of corroding RC beams are combined with sparse crack width measurements in order to obtain absolute CLs. The proposed methodology is experimentally validated by corroding eight beams with varying dimensions, corrosion zones, and reinforcement layouts. The experimental results prove that the estimated CLs closely match the rebar mass losses, with a mean absolute error of 1.53% CL for beams reaching up to 14% CL, confirming the potential of the combined AE and crack width measurement technique as an efficient and accurate condition assessment approach. Moreover, AE sensing provides detailed spatial variability of the rebar corrosion in the monitored zone, which is challenging to obtain with conventional techniques. By using this dual‐technique approach, shorter monitoring periods prove nearly as effective as continuous AE monitoring in accurately estimating CLs.
- 15 October 2024
- Published by Wiley in Structural Concrete
- Vol. 26 (5) , 5578-5595
Corrosion level estimation in reinforced concrete beams by acoustic emission sensing and selective crack measurements
Accurate corrosion assessment plays an important role in ensuring structural safety of reinforced concrete (RC) structures. However, on‐site assessment of existing concrete structures presents many challenges, including high costs, limited inspection timeframes, and difficult accessibility. To facilitate inspection‐based corrosion assessment, this paper presents a novel approach by combining short‐term acoustic emission (AE) monitoring with selective crack width measurements for corrosion level (CL) assessment. AE sensing is a monitoring technique which can detect ongoing internal degradation mechanisms by analyzing ultrasonic waves emitted by the damage process. Yet, two major challenges arise on site: (1) practical limitations prevent continuous AE monitoring over the structure's entire lifetime and (2) AE can only generate relative results in the absence of reference measurements. This paper addresses both challenges to bridge the gap between laboratory experiments and on‐site monitoring of corroding RC structures. First, short periods of AE monitoring data are analyzed to investigate the potential of AE sensing over limited timeframes. Second, AE data of corroding RC beams are combined with sparse crack width measurements in order to obtain absolute CLs. The proposed methodology is experimentally validated by corroding eight beams with varying dimensions, corrosion zones, and reinforcement layouts. The experimental results prove that the estimated CLs closely match the rebar mass losses, with a mean absolute error of 1.53% CL for beams reaching up to 14% CL, confirming the potential of the combined AE and crack width measurement technique as an efficient and accurate condition assessment approach. Moreover, AE sensing provides detailed spatial variability of the rebar corrosion in the monitored zone, which is challenging to obtain with conventional techniques. By using this dual‐technique approach, shorter monitoring periods prove nearly as effective as continuous AE monitoring in accurately estimating CLs.
- Open Access
- 1 October 2024
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 29 (10)
Acoustic emission monitoring of a large-scale 50-year-old prestressed concrete bridge girder during an eccentric three-point bending test
Deterioration of reinforced and prestressed concrete structures is one of the main challenges in structural engineering. As the majority of our infrastructure is built around 1960-1980, most structures have reached or will soon reach their design lifetime, giving rise to more structural problems and costs in the coming decades. It is therefore important to develop efficient assessment schemes allowing to assure the safety and reliability of these existing structures and to estimate their residual lifetime. Within the framework of the Bridge|50 research project, a 50-year-old prestressed concrete bridge showing signs of corrosion damage was decommissioned. The bridge girders were recovered and have been subjected to large-scale load tests with varying loading patterns. This paper presents the results acquired during acoustic emission (AE) monitoring of one of the I-shaped girders during a monotonic three-point bending test with an eccentric point load. The results show that the failure mode and location could be detected based on AE activity and zonal AE localization. The onset of concrete cracking was observed by a decrease in peak frequency of the AE signals. Average frequency (AF) and rise angle (RA) value analysis was used to characterize the crack mode, which shifted from tensile to shear mode during bending.
- 1 October 2024
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 29 (10)
Open AccessAcoustic emission monitoring of a large-scale 50-year-old prestressed concrete bridge girder during an eccentric three-point bending test
Deterioration of reinforced and prestressed concrete structures is one of the main challenges in structural engineering. As the majority of our infrastructure is built around 1960-1980, most structures have reached or will soon reach their design lifetime, giving rise to more structural problems and costs in the coming decades. It is therefore important to develop efficient assessment schemes allowing to assure the safety and reliability of these existing structures and to estimate their residual lifetime. Within the framework of the Bridge|50 research project, a 50-year-old prestressed concrete bridge showing signs of corrosion damage was decommissioned. The bridge girders were recovered and have been subjected to large-scale load tests with varying loading patterns. This paper presents the results acquired during acoustic emission (AE) monitoring of one of the I-shaped girders during a monotonic three-point bending test with an eccentric point load. The results show that the failure mode and location could be detected based on AE activity and zonal AE localization. The onset of concrete cracking was observed by a decrease in peak frequency of the AE signals. Average frequency (AF) and rise angle (RA) value analysis was used to characterize the crack mode, which shifted from tensile to shear mode during bending.
- 16 August 2024
- Published by Elsevier in Engineering Structures
- Vol. 318
Dynamic stiffness parameter assessment of cracked reinforced concrete beams: A numerical and experimental study
- 16 August 2024
- Published by Elsevier in Engineering Structures
- Vol. 318
Dynamic stiffness parameter assessment of cracked reinforced concrete beams: A numerical and experimental study
- 19 March 2024
- Published by Elsevier in Engineering Structures
- Vol. 306
Vibration monitoring and acoustic emission sensing during progressive load tests of corroded reinforced concrete beams
- 19 March 2024
- Published by Elsevier in Engineering Structures
- Vol. 306
Vibration monitoring and acoustic emission sensing during progressive load tests of corroded reinforced concrete beams
- 20 February 2024
- Published by Springer Nature
- p. 1166-1177
Corrosion Level Prediction with Acoustic Emission Sensing and Crack Measurements
- 20 February 2024
- Published by Springer Nature
- p. 1166-1177
Corrosion Level Prediction with Acoustic Emission Sensing and Crack Measurements
- 18 July 2023
- Published by Elsevier in Engineering Structures
- Vol. 293
Experimental study on acoustic emission sensing and vibration monitoring of corroding reinforced concrete beams
- 18 July 2023
- Published by Elsevier in Engineering Structures
- Vol. 293
Experimental study on acoustic emission sensing and vibration monitoring of corroding reinforced concrete beams
- 20 March 2023
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 22 (6) , 4233-4251
Challenges in assessing corrosion damage in reinforced concrete beams by vibration-based monitoring: literature analysis and experimental study
Corrosion is one of the most frequently occurring problems in reinforced concrete (RC) structures. The formation of rust products results in deterioration processes that decrease the durability and structural capacity. Therefore, frequent inspection and monitoring of corrosion damage play a vital role in establishing reliable asset management of civil structures. Vibration-based monitoring (VBM) is particularly useful in studying the global response of a deteriorated structure, since a change in modal characteristics may indicate damage. Although VBM has already been studied thoroughly, a systematic understanding of how corrosion contributes to the changes in modal characteristics is still lacking. In this study, an overview and assessment of the existing literature for dynamic tests on corroded RC beams is provided, aiming to give a critical review of the current knowledge, possibilities and challenges related to this topic. Moreover, this study presents additional data from two test programmes, which enable to point out the challenges in VBM of corroding RC beams. The experimental test programmes include two locally corroded beams and three uniformly corroded beams, as well as non-corroding reference beams. For high corrosion levels, the natural frequencies of beams reported in the literature, as well as the beams of the test programmes, decreased. However, comparison with a non-corroding reference beam proved to be essential to eliminate the influence of other non-negligible factors such as creep and shrinkage. Other modal characteristics, such as the damping ratio and mode shapes, are found to be less sensitive to monitor uniform or local corrosion in RC beams.
- 20 March 2023
- Published by SAGE Publications in Structural Health Monitoring
- Vol. 22 (6) , 4233-4251
Challenges in assessing corrosion damage in reinforced concrete beams by vibration-based monitoring: literature analysis and experimental study
Corrosion is one of the most frequently occurring problems in reinforced concrete (RC) structures. The formation of rust products results in deterioration processes that decrease the durability and structural capacity. Therefore, frequent inspection and monitoring of corrosion damage play a vital role in establishing reliable asset management of civil structures. Vibration-based monitoring (VBM) is particularly useful in studying the global response of a deteriorated structure, since a change in modal characteristics may indicate damage. Although VBM has already been studied thoroughly, a systematic understanding of how corrosion contributes to the changes in modal characteristics is still lacking. In this study, an overview and assessment of the existing literature for dynamic tests on corroded RC beams is provided, aiming to give a critical review of the current knowledge, possibilities and challenges related to this topic. Moreover, this study presents additional data from two test programmes, which enable to point out the challenges in VBM of corroding RC beams. The experimental test programmes include two locally corroded beams and three uniformly corroded beams, as well as non-corroding reference beams. For high corrosion levels, the natural frequencies of beams reported in the literature, as well as the beams of the test programmes, decreased. However, comparison with a non-corroding reference beam proved to be essential to eliminate the influence of other non-negligible factors such as creep and shrinkage. Other modal characteristics, such as the damping ratio and mode shapes, are found to be less sensitive to monitor uniform or local corrosion in RC beams.