Januar Irawan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Januar Irawan has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Fariza Eka Yunita
National Research and Innovation Agency
2 shared publications - Florentinus Firdiyono
National Research and Innovation Agency
2 shared publications Adi Noer Syahid
National Research and Innovation Agency
1 shared publication- Agus Budi Prasetyo
Center of Minerals Processing and Corrosion Research, Department of Metallurgical and Materials Engineering, Universitas Indonesia, Depok 16424, Indonesia
1 shared publication - Akhmad Herman Yuwono
Department of Metallurgical and Materials Engineering, Faculty of Engineering, Universitas Indonesia, Depok, Indonesia
1 shared publication Annisa Nabilah
Universitas Sultan Ageng Tirtayasa
1 shared publication
Latest Publications
- Open Access
- 31 December 2023
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 38 (3) , 109-116
Kinetic of Dissolution of Nickel Limonite Calcine by Sulfuric Acid Solution
Currently, more than 60% of nickel processing is carried out using nickel sulfide as a raw material. Nonetheless, due to the depletion reserves of nickel sulphide, nickel laterite has drawn a lot of interest to be processed as raw material. Nickel laterite in Indonesia is generally found in low grades, with nickel concentration of <1.15%. One method of treating nickel limonite is leaching in a sulfuric acid solution. This study aims to determine the reaction rate in the leaching process of calcine nickel limonite and the effect of sulfuric acid concentration and leaching temperature on the percent nickel extraction. In this research, the limonite ore from Pomalaa, Southeast Sulawesi, Indonesia, which has undergone a reduction process, was used as raw material. This research was conducted by leaching method on nickel limonite calcine using sulfuric acid reagent with 0.2, 0.5, and 1 M concentration variation, temperature variations of 60, 70, and 90°C, stirring speed 500 rpm, and %S/L (w/w) 10%. In this leaching research, the activation energy obtained at a sulfuric acid concentration of 0.2, 0.5, and 1 M are 13,7379 kJ/mol, 19,7582 kJ/mol, 20,3161 kJ/mol, respectively. The leaching process of nickel limonite calcine was controlled by diffusion. The optimum nickel extraction percentage in this study was 97.45%, obtained at a concentration of 1 M sulfuric acid, temperature of 70 °C, and leaching time of 240 minutes.
- 31 December 2023
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 38 (3) , 109-116
Open AccessKinetic of Dissolution of Nickel Limonite Calcine by Sulfuric Acid Solution
Currently, more than 60% of nickel processing is carried out using nickel sulfide as a raw material. Nonetheless, due to the depletion reserves of nickel sulphide, nickel laterite has drawn a lot of interest to be processed as raw material. Nickel laterite in Indonesia is generally found in low grades, with nickel concentration of <1.15%. One method of treating nickel limonite is leaching in a sulfuric acid solution. This study aims to determine the reaction rate in the leaching process of calcine nickel limonite and the effect of sulfuric acid concentration and leaching temperature on the percent nickel extraction. In this research, the limonite ore from Pomalaa, Southeast Sulawesi, Indonesia, which has undergone a reduction process, was used as raw material. This research was conducted by leaching method on nickel limonite calcine using sulfuric acid reagent with 0.2, 0.5, and 1 M concentration variation, temperature variations of 60, 70, and 90°C, stirring speed 500 rpm, and %S/L (w/w) 10%. In this leaching research, the activation energy obtained at a sulfuric acid concentration of 0.2, 0.5, and 1 M are 13,7379 kJ/mol, 19,7582 kJ/mol, 20,3161 kJ/mol, respectively. The leaching process of nickel limonite calcine was controlled by diffusion. The optimum nickel extraction percentage in this study was 97.45%, obtained at a concentration of 1 M sulfuric acid, temperature of 70 °C, and leaching time of 240 minutes.
- Open Access
- 30 December 2022
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 37 (3)
MORPHOLOGY AND RESISTIVITY VALUE OF FLOURINE-DOPED TIN OXIDE (FTO) USING INDONESIAN LOCAL DIMETHYLTIN DICHLORIIDE (DTMC) PRECURSORS
Transparent Conductive Oxide (TCO) is the main component for solar cell fabrication. One of the promising types of TCO is fluorine-doped tin oxide (FTO). The method used in depositing the conductive layer of FTO is spray pyrolysis with an ultrasonic nebulizer. The precursor is a local Indonesian product, dimethyl tin dichloride (DMTC), with doping ammonium fluoride (NH4F). The variable that used in this study were variations in deposition time (5. 10. 15. 20, and 25 minutes) with a fixed substrate temperature at 300°C and doping variations (un-doped, 2 wt.% doped and 8 wt.% doped) to see the effect of adding F doping to the precursor solution. The resistivity value with deposition time of 5. 10. 15. 20 and 25 minute (2 wt.% doped) is 0.218x100; 0.449x10-1; 1,567x10-2; 0.676x10-2 0.377x10-2 Ω.cm. For doping variations (un-doped, 2 wt% doped and 8 wt% doped) the value is 0.883x10-2; 0.377x10-2; 0.506x10-3 Ω.cm. There is a decreasing trend in the resistivity values obtained along with the increase in deposition time and the addition of doping to obtain better conductive properties. The grain size will increase with increasing deposition time and the addition of doping. The optimum resistivity value obtained in this study was 0.377x10-2 Ω.cm, obtained at the deposition time of 25 minutes with 2 wt.% doping.
- 30 December 2022
- Published by National Research and Innovation Agency in Metalurgi
- Vol. 37 (3)
Open AccessMORPHOLOGY AND RESISTIVITY VALUE OF FLOURINE-DOPED TIN OXIDE (FTO) USING INDONESIAN LOCAL DIMETHYLTIN DICHLORIIDE (DTMC) PRECURSORS
Transparent Conductive Oxide (TCO) is the main component for solar cell fabrication. One of the promising types of TCO is fluorine-doped tin oxide (FTO). The method used in depositing the conductive layer of FTO is spray pyrolysis with an ultrasonic nebulizer. The precursor is a local Indonesian product, dimethyl tin dichloride (DMTC), with doping ammonium fluoride (NH4F). The variable that used in this study were variations in deposition time (5. 10. 15. 20, and 25 minutes) with a fixed substrate temperature at 300°C and doping variations (un-doped, 2 wt.% doped and 8 wt.% doped) to see the effect of adding F doping to the precursor solution. The resistivity value with deposition time of 5. 10. 15. 20 and 25 minute (2 wt.% doped) is 0.218x100; 0.449x10-1; 1,567x10-2; 0.676x10-2 0.377x10-2 Ω.cm. For doping variations (un-doped, 2 wt% doped and 8 wt% doped) the value is 0.883x10-2; 0.377x10-2; 0.506x10-3 Ω.cm. There is a decreasing trend in the resistivity values obtained along with the increase in deposition time and the addition of doping to obtain better conductive properties. The grain size will increase with increasing deposition time and the addition of doping. The optimum resistivity value obtained in this study was 0.377x10-2 Ω.cm, obtained at the deposition time of 25 minutes with 2 wt.% doping.
- Open Access
- 18 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (6 (111)) , 32-40
Implementation of sulfuric acid leaching for aluminum and iron removal for improvement of low-grade silica from quartz sand of Sukabumi, Indonesia
Indonesia has very abundant reserves of silica, but progressive studies on the deposition of this material are very few, resulting in limited applications of silica. This work refers to the purification of silica from quartz sand originated from Sukabumi, Indonesia to obtain high-purity silica, which can be applied as important raw materials for special purposes. The aim of our research is to improve low-grade silica from quartz sand by removing impurities, especially aluminum and iron removal, using sulfuric acid leaching. In order to achieve the aim, the effect of reaction time and sulfuric acid concentration on the leaching process was investigated. The effectiveness of sulfuric acid for the impurities removal was observed. The chemical composition of the samples before and after leaching was studied using X-ray fluorescence. The mineralogical analysis of the starting materials and the products was conducted using X-ray diffraction. Microstructure analysis was performed using a scanning electron microscope, and EDS test was used to show the element composition at different points. The experimental results show that the optimum condition of the leaching process occurs at a reaction time of 5 hours with a sulfuric acid concentration of 10 N. The silica levels increase from 93.702 % to 96.438 %. Aluminum and iron impurities reduced from 4.691 % to 2.712 % and from 0.641 % to 0.094 %, respectively. At this optimum point, sulfuric acid is very effective to remove aluminum and iron impurities up to 42 % and 85 %, respectively. The results of this research can be a very significant opportunity to increase the value added of quartz sand from Sukabumi, which can enhance the quality of low-grade silica to provide better raw materials for glass industries.
- 18 June 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (6 (111)) , 32-40
Open AccessImplementation of sulfuric acid leaching for aluminum and iron removal for improvement of low-grade silica from quartz sand of Sukabumi, Indonesia
Indonesia has very abundant reserves of silica, but progressive studies on the deposition of this material are very few, resulting in limited applications of silica. This work refers to the purification of silica from quartz sand originated from Sukabumi, Indonesia to obtain high-purity silica, which can be applied as important raw materials for special purposes. The aim of our research is to improve low-grade silica from quartz sand by removing impurities, especially aluminum and iron removal, using sulfuric acid leaching. In order to achieve the aim, the effect of reaction time and sulfuric acid concentration on the leaching process was investigated. The effectiveness of sulfuric acid for the impurities removal was observed. The chemical composition of the samples before and after leaching was studied using X-ray fluorescence. The mineralogical analysis of the starting materials and the products was conducted using X-ray diffraction. Microstructure analysis was performed using a scanning electron microscope, and EDS test was used to show the element composition at different points. The experimental results show that the optimum condition of the leaching process occurs at a reaction time of 5 hours with a sulfuric acid concentration of 10 N. The silica levels increase from 93.702 % to 96.438 %. Aluminum and iron impurities reduced from 4.691 % to 2.712 % and from 0.641 % to 0.094 %, respectively. At this optimum point, sulfuric acid is very effective to remove aluminum and iron impurities up to 42 % and 85 %, respectively. The results of this research can be a very significant opportunity to increase the value added of quartz sand from Sukabumi, which can enhance the quality of low-grade silica to provide better raw materials for glass industries.