ASAnkit Sharma

Ankit Sharma

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ankit Sharma has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Fabrication and Mechanical Properties of Tri‐Layer B4C‐Reinforced Al–Zn Functionally Graded Foam Having Higher Energy Absorption Efficiency

    by Ankit Sharma, Sujith Ravindran, Amit Kumar Gupta

    Metal foams are lightweight and have a higher impact energy absorption ability, making them suitable for various dynamic load applications. However, thin cell walls having higher porosity and lower compressive strength limit the foam's application. Density‐graded foams have superior compressive properties to uniform foam, making them a suitable lightweight candidate for dynamic loading applications. The tri‐layer functionally graded foam material (FGFM) is fabricated using the hot pressure‐assisted sintering and dissolution route by varying the porosity and B4C reinforcement. The density gradation enhances the load‐bearing capacity compared to uniform foam, and the maximum compressive strength achieved is 142 MPa. Also, the densification strain is 26% higher compared to uniform foam. B4C (9 vol%)‐reinforced FGFM shows the highest energy absorption efficiency of ≈67% due to their stabilized plateau region.


  • B4C‐Reinforced Al–Zn Foams Having Superior Energy Absorption Efficiency

    by Ankit Sharma, Sai Srinivasan Kanyadhan Vijayaraghavan, Amit Kumar Gupta, Sujith Ravindran

    The low density of the aluminium foam and high energy absorption make them favourable for automobile, aerospace, and defence industries. However, the melt route for foam fabrication has challenges in achieving homogeneous distribution of pores. Hence, we have adopted the space holder technique using the powder metallurgy methodology to overcome such a challenge. In the current study, we fabricated Al–Zn alloy foams reinforced with varying volume fractions of B4C particles using NaCl as a space holder implemented by hot pressure‐assisted sintering and dissolution. X‐ray computed tomography revealed a homogeneous distribution of pores. The quasistatic compression studies showed that the samples containing a higher volume fraction of pores exhibited higher energy absorption efficiency in the fabricated foam. The maximum energy absorption efficiency (η) achieved was ≈93% for the pristine Al alloy foam with ≈50% porosity, which is ≈11% higher than the η value of 9 vol% B4C samples with similar porosity. Additionally, B4C particles delay the sudden collapse of cell walls and stabilize the compression behaviour. Adding B4C improves the η and strength at higher relative density. This fabrication methodology would help us develop foams with a homogenous pore distribution and regular geometry, achieving highly desirable mechanical properties.


  • Biodegradability of Magnesium and Graphene Nanoplatelet Reinforced Magnesium in Simulated Body Fluids

    by Ankit Sharma, Ayush Morchhale, Ananya V.K., Sujith Ravindran, Sudagar Jothi

    In this study, the biocompatibility of graphene nanoplatelet (GNP) reinforced Mg composites towards hydroxyapatite mineralization is investigated in the simulated body fluids. The hydrogen evolution, weight loss, and electrochemical studies were conducted in modified simulated body fluid (m-SBF) for a short-term duration to evaluate the corrosion properties. The powder metallurgy route was used to fabricate the composites, and the X-ray diffraction study revealed insignificant oxide or carbide formation. The overall density of GNP reinforced material decreased by approximately 14% when compared with the unreinforced one. The corrosion studies in m-SBF for 24 h indicated that the GNP reinforced composite is susceptible to higher degradation. A lower Ca/P ratio was observed in the GNP reinforced composites compared to the pure magnesium due to the higher Mg(OH) 2 corrosive layer. The GNP reinforced composite displayed approximately 21% weight loss and showed a higher amount of hydrogen evolution. The corrosion properties of these composites were further established with electrochemical impedance spectroscopy measurements. The corresponding Bode impedance plots suggest that the addition of GNP in magnesium reduced the stability of Mg(OH) 2 and resulted in the enhanced dissolution of Cl − ions from m-SBF solution.


  • Effect of Graphene Nanoplatelets Incorporation on Microstructural and Tribological Properties of Aluminium Metal Matrix Composites

    by Ankit Sharma, Amrita Priyadarshini, Ravindran Sujith, M. V. Sankara Subrahmanyam, P. Alen Thomas, Amit Kumar Gupta

    Aluminium metal matrix composites exhibiting superior mechanical and tribological properties have gained immense interest in recent years. These comosites are finding broad applications in the fields of automotive, aerospace, military and marine. Graphene Nanoplatelets (GNPs), as reinforcement in composites, have become a prime focus because of its exceptional characteristic properties. In the present study, GNPs are dispersed into the aluminium alloy as reinforcements by using stir casting method. To ensure proper dispersion, sintered pellets of aluminium mixed with GNPs are added to the molten metal. The dispersion of the GNPs and the microstructural changes due to the addition of GNPs are observed using Scanning Electron Microscopy (SEM) and elemental mapping. Vickers hardness tester is used to measure hardness of these samples. To compare the tribological properties of Al/GNP composite as well as pure alumimum samples, pin-on-disc experiments are conducted for a specific combination of sliding speed and sliding distance at different loading conditions. The weight loss, wear rate and coefficient of friction are measured and favourable effects of GNPs on tribological properties of Al/GNP composite are discussed. In addition, the wear mechanism has been understood in detail by conducting microstructural studies of the worn surfaces using SEM and Energy Dispersive Spectroscopy. It is observed that the Vickers hardness of the composite increased to a maximum of 25% while coefficient of friction decreased to a minimum of 26% for Al/GNP composite.