Shivendra K. Rathaur
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Shivendra K. Rathaur has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Edward Yi Chang
Department of Materials Science and Engineering National Yang Ming Chiao Tung University Hsinchu 300 Taiwan
4 shared publications - Abhisek Dixit
Department of Electrical Engineering, Indian Institute of Technology Delhi, New Delhi, India
3 shared publications - Tsung-Ying Yang
International College of Semiconductor Technology, National Yang Ming Chiao Tung University, Hsinchu 300, Taiwan
3 shared publications Abhisek Dixit
Department of Electrical Engineering, Indian Institute of Technology 1 Delhi, New Delhi 110016, India
2 shared publicationsEdward Yi Chang
International College of Semiconductor Technology, National Yang Ming Chiao Tung University 2 , Hsinchu 30010, Taiwan
2 shared publications- Jui-Sheng Wu
National yang Ming Chiao Tung University
2 shared publications
Latest Publications
- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 24 (1536125X) , 42-47
Improvement of the Enhancement-Mode GaN MIS-HEMTs by Fluorine Doping in the Dielectric Gate Stack
This study tested fluorine doping on various regions of the ferroelectric charge trap gate stack (FEG stack). Fluorine doping effectively reduces oxygen vacancies in the dielectric layer, thus reducing leakage current and stabilizing charge in the dielectric layer. Moreover, fluorine doping can passivate the dangling bonds at the interface and increase the ability of trapping carriers in the trap layer. The FEG stack comprises a tunnel oxide layer (TL), a charge trap layer (CTL), and a ferroelectric layer (FE). Four types of devices were fabricated: undoped, doping in TL, doping in CTL, and doping in both TL and CTL, to investigate the impact of fluorine doping on the FEG gate stack. Devices doping in TL and CTL demonstrated superior performance, achieving the highest Vth of 5.4 V with a retention time of 70.42% after 10,000 seconds. The off-state and gate leakage tests revealed impressive breakdown voltages of 735 V and 24.55 V, respectively. Furthermore, the device exhibited a high operation voltage of 14.3 V for a 10-year lifetime prediction, enabling a wide operating range.
- 25 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nanotechnology
- Vol. 24 (1536125X) , 42-47
Improvement of the Enhancement-Mode GaN MIS-HEMTs by Fluorine Doping in the Dielectric Gate Stack
This study tested fluorine doping on various regions of the ferroelectric charge trap gate stack (FEG stack). Fluorine doping effectively reduces oxygen vacancies in the dielectric layer, thus reducing leakage current and stabilizing charge in the dielectric layer. Moreover, fluorine doping can passivate the dangling bonds at the interface and increase the ability of trapping carriers in the trap layer. The FEG stack comprises a tunnel oxide layer (TL), a charge trap layer (CTL), and a ferroelectric layer (FE). Four types of devices were fabricated: undoped, doping in TL, doping in CTL, and doping in both TL and CTL, to investigate the impact of fluorine doping on the FEG gate stack. Devices doping in TL and CTL demonstrated superior performance, achieving the highest Vth of 5.4 V with a retention time of 70.42% after 10,000 seconds. The off-state and gate leakage tests revealed impressive breakdown voltages of 735 V and 24.55 V, respectively. Furthermore, the device exhibited a high operation voltage of 14.3 V for a 10-year lifetime prediction, enabling a wide operating range.
- 2 September 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (10)
Impact of temperature on threshold voltage instability under negative bias in ferroelectric charge trap (FEG) GaN-HEMT
This Letter pioneers an investigation into the influence of temperature on threshold voltage (VTH) instability under negative bias in ferroelectric charge trap gate stack (FEG) high electron mobility transistors. Based on the experimental stress condition, i.e., gate bias of −20 V and temperature (T) range from 30 to 150 °C, our findings reveal a unidirectional VTH shift with 30 °C < T < 90 °C, and transitioning to a bidirectional VTH shift at 90 °C ≤ T ≤ 150 °C. The observed VTH < 0 V can be ascribed to the emission of electrons from the trapping layer, prompted by the pre-poling of the ferroelectric (FE) layer and the presence of interface traps. In contrast, under high-temperature stress, where VTH > 0 V, it indicates the depletion of the two-dimensional electron gas electrons due to de-poling and saturation of the polarization in the reverse direction. Moreover, this phenomenon is consistent with extracted activation energies (Ea) of 0.55 ± 0.01 and 0.79 ± 0.01 eV. Additionally, the recovery characteristics validate the trapping/detrapping process.
- 2 September 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (10)
Impact of temperature on threshold voltage instability under negative bias in ferroelectric charge trap (FEG) GaN-HEMT
This Letter pioneers an investigation into the influence of temperature on threshold voltage (VTH) instability under negative bias in ferroelectric charge trap gate stack (FEG) high electron mobility transistors. Based on the experimental stress condition, i.e., gate bias of −20 V and temperature (T) range from 30 to 150 °C, our findings reveal a unidirectional VTH shift with 30 °C < T < 90 °C, and transitioning to a bidirectional VTH shift at 90 °C ≤ T ≤ 150 °C. The observed VTH < 0 V can be ascribed to the emission of electrons from the trapping layer, prompted by the pre-poling of the ferroelectric (FE) layer and the presence of interface traps. In contrast, under high-temperature stress, where VTH > 0 V, it indicates the depletion of the two-dimensional electron gas electrons due to de-poling and saturation of the polarization in the reverse direction. Moreover, this phenomenon is consistent with extracted activation energies (Ea) of 0.55 ± 0.01 and 0.79 ± 0.01 eV. Additionally, the recovery characteristics validate the trapping/detrapping process.
- 16 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 24 (3) , 428-436
Performance and Threshold Voltage Reliability of Quaternary InAlGaN/GaN MIS-HEMT on Si for Power Device Applications
In this study, we empirically explore the performance degradation of quaternary InAlGaN/AlN/GaN Metal-Insulator-Semiconductor High Electron Mobility Transistors (MIS-HEMTs) with a Gate Field Plate (GFP) structure under a Positive Bias Temperature Instability (PBTI) and Negative Bias Temperature Instability (NBTI) stresses. Both stress conditions (PBTI with VGS = 10 V and NBTI with VGS = -30 V) are applied. The experimental findings reveal a positive shift in threshold voltage (VTH), indicating the presence of a net negative charge beneath the gate area. However, we find distinct degradation dynamics for both stress experiments. During PBTI, the VTH shift remains temperature independent, suggesting the generation of defects leading to electron trapping in the insulator. In NBTI, critical defects are identified, resulting in a permanent VTH shift with temperature dependence. Furthermore, the extracted activation energy (Ea) from Arrhenius plots in PBTI is determined to be 0.14 eV and 0.11 eV, highlighting the crucial role of shallow C-related traps governed by the Shockley-Read Hall (SRH) recombination process. In contrast, for NBTI, Ea = 0.12 eV, indicating the involvement of surface traps and thermalassisted de-trapping kinetics, leading to the generation of permanent defects. These results underscore the distinct dynamics of performance degradation phenomena in PBTI and NBTI involves different trap energies at different locations within the device structure.
- 16 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 24 (3) , 428-436
Performance and Threshold Voltage Reliability of Quaternary InAlGaN/GaN MIS-HEMT on Si for Power Device Applications
In this study, we empirically explore the performance degradation of quaternary InAlGaN/AlN/GaN Metal-Insulator-Semiconductor High Electron Mobility Transistors (MIS-HEMTs) with a Gate Field Plate (GFP) structure under a Positive Bias Temperature Instability (PBTI) and Negative Bias Temperature Instability (NBTI) stresses. Both stress conditions (PBTI with VGS = 10 V and NBTI with VGS = -30 V) are applied. The experimental findings reveal a positive shift in threshold voltage (VTH), indicating the presence of a net negative charge beneath the gate area. However, we find distinct degradation dynamics for both stress experiments. During PBTI, the VTH shift remains temperature independent, suggesting the generation of defects leading to electron trapping in the insulator. In NBTI, critical defects are identified, resulting in a permanent VTH shift with temperature dependence. Furthermore, the extracted activation energy (Ea) from Arrhenius plots in PBTI is determined to be 0.14 eV and 0.11 eV, highlighting the crucial role of shallow C-related traps governed by the Shockley-Read Hall (SRH) recombination process. In contrast, for NBTI, Ea = 0.12 eV, indicating the involvement of surface traps and thermalassisted de-trapping kinetics, leading to the generation of permanent defects. These results underscore the distinct dynamics of performance degradation phenomena in PBTI and NBTI involves different trap energies at different locations within the device structure.
- 10 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 24 (3) , 414-421
Investigation on Traps Dynamics & Negative Bias Stress in D-Mode GaN-on-Si Power MIS HEMTs Under High-Temperature
This experimental study investigates the traps dynamics and threshold voltage (VTH) shift mechanism under negative bias temperature stress for the GaN-on-Si Power MIS HEMTs on field plate design structure. Based on the experimental analysis, two distinct activation energies (Ea) have been identified under the specific reverse bias conditions of VGS = -30 V and VDS = 0 V in a wide temperature range. Reverse bias stress experiments (up to 10 ks) show a positive VTH shift of 1.6 V at room temperature due to the inversion of the charges at the interface between the insulator and AlGaN layer, resulting in net negative charge near the gate region. Subsequently, there is a decrease in VTH shift till 125 ° C because of the de-trapping of the inversion charges. This phenomenon shows a strong correlation with a thermally activated activation energy of (E a ≈ 0.23 eV). Further, the shift in VTH turns negative when the temperature is raised to 175 ° C, indicating the accumulation of electrons in the channel layer with activation energy (Ea ≈ 0.78 eV) attributed to the activation of nitrogen interstitials from the GaN buffer layer. Additionally, the recovery (up to 10 ks) behavior demonstrates the exponential-linear settlement of the traps to recover the VTH shift. Moreover, nitrogen interstitials take more time to suppress the threshold voltage instabilities. These findings explain the VTH shift mechanisms in GaN-on-Si Power MIS HEMTs under NBTI.
- 10 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 24 (3) , 414-421
Investigation on Traps Dynamics & Negative Bias Stress in D-Mode GaN-on-Si Power MIS HEMTs Under High-Temperature
This experimental study investigates the traps dynamics and threshold voltage (VTH) shift mechanism under negative bias temperature stress for the GaN-on-Si Power MIS HEMTs on field plate design structure. Based on the experimental analysis, two distinct activation energies (Ea) have been identified under the specific reverse bias conditions of VGS = -30 V and VDS = 0 V in a wide temperature range. Reverse bias stress experiments (up to 10 ks) show a positive VTH shift of 1.6 V at room temperature due to the inversion of the charges at the interface between the insulator and AlGaN layer, resulting in net negative charge near the gate region. Subsequently, there is a decrease in VTH shift till 125 ° C because of the de-trapping of the inversion charges. This phenomenon shows a strong correlation with a thermally activated activation energy of (E a ≈ 0.23 eV). Further, the shift in VTH turns negative when the temperature is raised to 175 ° C, indicating the accumulation of electrons in the channel layer with activation energy (Ea ≈ 0.78 eV) attributed to the activation of nitrogen interstitials from the GaN buffer layer. Additionally, the recovery (up to 10 ks) behavior demonstrates the exponential-linear settlement of the traps to recover the VTH shift. Moreover, nitrogen interstitials take more time to suppress the threshold voltage instabilities. These findings explain the VTH shift mechanisms in GaN-on-Si Power MIS HEMTs under NBTI.
- Open Access
- 1 July 2024
- Published by IOP Publishing in Applied Physics Express
- Vol. 17 (7) , 076501
Reliability assessment of high-power GaN-HEMT devices with different buffers under influence of gate bias and high-temperature tests
This study compares Vth-instability in D-mode MIS-HEMT devices between two epitaxial layers, AlN/AlGaN/GaN superlattice-W1, and three-step graded AlGaN-W2. Experimental results demonstrate that W1 exhibits ∼13% less Vth-instability compared to W2, with distinct degradation regions at specific voltage ranges. With temperature variation (30 °C–150 °C), these regions are justified and revealed small positive Vth-shifts due to electron trapping, leading to temporary degradation, followed-by negative Vth-shifts from positive charge injection, culminating in catastrophic degradation attributing impact ionization at 30 °C during 0–30 V gate-step stress, with permanent failure observed. Analysis indicates W1-devices are more efficient and stable. Also, both layers operate reliably till VGS = 18 V, with ∼3% minor Vth instability.
- 1 July 2024
- Published by IOP Publishing in Applied Physics Express
- Vol. 17 (7) , 076501
Open AccessReliability assessment of high-power GaN-HEMT devices with different buffers under influence of gate bias and high-temperature tests
This study compares Vth-instability in D-mode MIS-HEMT devices between two epitaxial layers, AlN/AlGaN/GaN superlattice-W1, and three-step graded AlGaN-W2. Experimental results demonstrate that W1 exhibits ∼13% less Vth-instability compared to W2, with distinct degradation regions at specific voltage ranges. With temperature variation (30 °C–150 °C), these regions are justified and revealed small positive Vth-shifts due to electron trapping, leading to temporary degradation, followed-by negative Vth-shifts from positive charge injection, culminating in catastrophic degradation attributing impact ionization at 30 °C during 0–30 V gate-step stress, with permanent failure observed. Analysis indicates W1-devices are more efficient and stable. Also, both layers operate reliably till VGS = 18 V, with ∼3% minor Vth instability.
- 24 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (9) , 4584-4590
High-Temperature TDDB Investigation on High Performance-Centered Hybrid HZO/HfON/Al2O3, Ferro-Electric Charge-Trap (FEG) GaN-HEMT
This article investigates a hybrid ferroelectric charge trap (HFCT)-based HfZrO4/HfO $_{\textit{X}}$ N $_{\textit{Y}}$ / Al2O3/AlGaN/GaN gate-stack under constant positive gate voltage stress over time and temperature variability. The experimentally characterized breakdown (BD) analysis implies a thermally assisted tunneling (TAT) BD owing to the negative temperature coefficient of BD voltage. Moreover, the step gate stress depicts a relatively lower BD voltage of $\sim$ 20 V compared to the linear gate stress voltage of $\sim$ 21.85 V attributed to performance degradation due to stress. In addition, the Weibull distribution, which validates the intrinsic degradation of the gate-stack, is used to estimate its lifetime. An operating voltage of $\sim$ 7.41 V exhibits a ten-year lifetime at 150 $^{\circ}$ C extrapolated over multiple stress conditions. Furthermore, the activation energy from $\sim$ 0.63 to $\sim$ 0.67 eV validates deep-level E3 traps within the GaN barrier layer and the trapping of electrons during degradation, thus, revealing the point-level defect generation leading to the time-dependent gate dielectric BD (TDDB). The robustness and superior reliability of the HFCT gate-stack are recognized, and the single degradation mechanism contributes to the final device failure in the TDDB test.
- 24 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (9) , 4584-4590
High-Temperature TDDB Investigation on High Performance-Centered Hybrid HZO/HfON/Al2O3, Ferro-Electric Charge-Trap (FEG) GaN-HEMT
This article investigates a hybrid ferroelectric charge trap (HFCT)-based HfZrO4/HfO $_{\textit{X}}$ N $_{\textit{Y}}$ / Al2O3/AlGaN/GaN gate-stack under constant positive gate voltage stress over time and temperature variability. The experimentally characterized breakdown (BD) analysis implies a thermally assisted tunneling (TAT) BD owing to the negative temperature coefficient of BD voltage. Moreover, the step gate stress depicts a relatively lower BD voltage of $\sim$ 20 V compared to the linear gate stress voltage of $\sim$ 21.85 V attributed to performance degradation due to stress. In addition, the Weibull distribution, which validates the intrinsic degradation of the gate-stack, is used to estimate its lifetime. An operating voltage of $\sim$ 7.41 V exhibits a ten-year lifetime at 150 $^{\circ}$ C extrapolated over multiple stress conditions. Furthermore, the activation energy from $\sim$ 0.63 to $\sim$ 0.67 eV validates deep-level E3 traps within the GaN barrier layer and the trapping of electrons during degradation, thus, revealing the point-level defect generation leading to the time-dependent gate dielectric BD (TDDB). The robustness and superior reliability of the HFCT gate-stack are recognized, and the single degradation mechanism contributes to the final device failure in the TDDB test.
- 9 August 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (6) , 063505
Metal (Pt)/ferroelectric (SrBi2Ta2O9)/insulator (La2O3)/semiconductor (Si), MFIS structures for nonvolatile memory applications
Extended data retention is a cardinal impediment for ferroelectric memories and serves a pivotal role for nonvolatile memory applications. Here, nonvolatile Metal–Ferroelectric–Insulator–Semiconductor (MFIS) structures are fabricated by using thin films of Strontium Bismuth Tantalum Oxide (SrBi2Ta2O9) as ferroelectric and high-κ lanthanum oxide (La2O3) as a buffer insulator on p-Si substrates via RF magnetron sputtering. The grazing incidence x-ray diffraction analysis confirms the dominant (111) and (115) ferroelectric perovskite phases of SrBi2Ta2O9 thin films. Albeit, atomic force microscopy surface micrographs revealed highly smooth La2O3 and SBT (SrBi2Ta2O9) thin films with a surface roughness of ∼0.22 ± 0.04 nm and ∼1.05 ± 0.03 nm, respectively. Capacitance–voltage (C–V), capacitance–time (C–T), and current–voltage (I–V) characteristics of Pt/SrBi2Ta2O9/La2O3/Si, MFIS structures, exhibited a high memory window of ∼1.1 V at ±5 V sweep voltage, data retention measured until ∼104 s even on the extrapolation up to 10 years, and a low leakage current density of ∼12.8 μA/cm2 at −1 V and 300 K. Far from it, the probed conduction mechanism is studied for Pt/SrBi2Ta2O9/La2O3/Si MFIS device structures. The optimum nonvolatile memory characteristics are attributed to the high-quality SBT ferroelectric and the buffer layer La2O3/Si interface of the investigated MFIS structure and also assert from the control Pt/SBT/Pt and Pt/La2O3/Si results. Thus, the proposed Pt/SrBi2Ta2O9/La2O3/Si structure is a potential candidate for a gate stack of one-transistor (1T) type Ferroelectric Field-Effect Transistors nonvolatile memory applications.
- 9 August 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 119 (6) , 063505
Metal (Pt)/ferroelectric (SrBi2Ta2O9)/insulator (La2O3)/semiconductor (Si), MFIS structures for nonvolatile memory applications
Extended data retention is a cardinal impediment for ferroelectric memories and serves a pivotal role for nonvolatile memory applications. Here, nonvolatile Metal–Ferroelectric–Insulator–Semiconductor (MFIS) structures are fabricated by using thin films of Strontium Bismuth Tantalum Oxide (SrBi2Ta2O9) as ferroelectric and high-κ lanthanum oxide (La2O3) as a buffer insulator on p-Si substrates via RF magnetron sputtering. The grazing incidence x-ray diffraction analysis confirms the dominant (111) and (115) ferroelectric perovskite phases of SrBi2Ta2O9 thin films. Albeit, atomic force microscopy surface micrographs revealed highly smooth La2O3 and SBT (SrBi2Ta2O9) thin films with a surface roughness of ∼0.22 ± 0.04 nm and ∼1.05 ± 0.03 nm, respectively. Capacitance–voltage (C–V), capacitance–time (C–T), and current–voltage (I–V) characteristics of Pt/SrBi2Ta2O9/La2O3/Si, MFIS structures, exhibited a high memory window of ∼1.1 V at ±5 V sweep voltage, data retention measured until ∼104 s even on the extrapolation up to 10 years, and a low leakage current density of ∼12.8 μA/cm2 at −1 V and 300 K. Far from it, the probed conduction mechanism is studied for Pt/SrBi2Ta2O9/La2O3/Si MFIS device structures. The optimum nonvolatile memory characteristics are attributed to the high-quality SBT ferroelectric and the buffer layer La2O3/Si interface of the investigated MFIS structure and also assert from the control Pt/SBT/Pt and Pt/La2O3/Si results. Thus, the proposed Pt/SrBi2Ta2O9/La2O3/Si structure is a potential candidate for a gate stack of one-transistor (1T) type Ferroelectric Field-Effect Transistors nonvolatile memory applications.