A. Yu. Em
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
A. Yu. Em has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Konstantin V. Grigorovich
Baikov Institute of Metallurgy and Materials Science of the Russian Academy of Sciences
5 shared publications - O. A. Komolova
Baikov Institute of Metallurgy and Materials Science of the Russian Academy of Sciences
4 shared publications - A. O. Morozov
Baikov Institute of Metallurgy and Materials Science of the Russian Academy of Sciences
3 shared publications - A. A. Zhemkov
Baikov Institute of Metallurgy and Materials Science, Russian Academy of Sciences
2 shared publications A. A. Zhemkov
Baikov Institute of Metallurgy and Materials Science of the Russian Academy of Sciences
1 shared publication- A. D. Khoroshilov
Rosatom Metal Tech LLC
1 shared publication
Latest Publications
- 26 April 2026
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 69 (2)
Evolution of oxide non-metallic inclusions in production of pipe steel
Under the conditions of pipe rolling mill, during the production of 12 heats of medium-carbon aluminum-killed steel, 10 samples were taken from each heat at different stages of production – from the beginning of ladle treatment to pipe rolling. The samples were examined by high-temperature extraction in a carrier gas to determine the total oxygen content and by scanning electron microscopy to determine the composition and size distribution of non-metallic inclusions. The dynamics of change in the content of inclusions was established according to the following criteria: total oxygen content, volume fraction, density and average diameter of inclusions. The composition of non-metallic inclusions was plotted on ternary diagrams: the oxide component on the diagrams CaO – Al 2 O 3 – SiO 2 and CaO – Al 2 O 3 – MgO, the sulfide – on Ca – Mn – S. The trajectory of change in the chemical composition of inclusions in the steelmaking process was established. The paper shows the role of steel treatment with calcium and importance of observing thermodynamic conditions. A relationship is established between deviations in calcium treatment parameters, composition of non-metallic inclusions, steel castability and sorting of pipe products by surface and internal defects. Decreasing total oxygen content, practically does not occur at the main stage of ladle treatment. The highest intensity of steel refining from inclusions is observed at the stage between the samples before and after steel treatment with calcium, this time interval is less than 10 min. Comparison of the obtained data on the chemical composition of inclusions with the calculated data on the boundary of liquid phase region of the CaO – Al 2 O 3 – SiO 2 – MgO system shows that at this stage, the chemical and phase composition of non-metallic inclusions is transformed. After the addition of calcium, the composition of oxide non-metallic inclusions shifted to the liquid region of the CaO – Al 2 O 3 – SiO 2 system at MgO content of 10 wt. % and 1600 °C.
- 26 April 2026
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 69 (2)
Evolution of oxide non-metallic inclusions in production of pipe steel
Under the conditions of pipe rolling mill, during the production of 12 heats of medium-carbon aluminum-killed steel, 10 samples were taken from each heat at different stages of production – from the beginning of ladle treatment to pipe rolling. The samples were examined by high-temperature extraction in a carrier gas to determine the total oxygen content and by scanning electron microscopy to determine the composition and size distribution of non-metallic inclusions. The dynamics of change in the content of inclusions was established according to the following criteria: total oxygen content, volume fraction, density and average diameter of inclusions. The composition of non-metallic inclusions was plotted on ternary diagrams: the oxide component on the diagrams CaO – Al 2 O 3 – SiO 2 and CaO – Al 2 O 3 – MgO, the sulfide – on Ca – Mn – S. The trajectory of change in the chemical composition of inclusions in the steelmaking process was established. The paper shows the role of steel treatment with calcium and importance of observing thermodynamic conditions. A relationship is established between deviations in calcium treatment parameters, composition of non-metallic inclusions, steel castability and sorting of pipe products by surface and internal defects. Decreasing total oxygen content, practically does not occur at the main stage of ladle treatment. The highest intensity of steel refining from inclusions is observed at the stage between the samples before and after steel treatment with calcium, this time interval is less than 10 min. Comparison of the obtained data on the chemical composition of inclusions with the calculated data on the boundary of liquid phase region of the CaO – Al 2 O 3 – SiO 2 – MgO system shows that at this stage, the chemical and phase composition of non-metallic inclusions is transformed. After the addition of calcium, the composition of oxide non-metallic inclusions shifted to the liquid region of the CaO – Al 2 O 3 – SiO 2 system at MgO content of 10 wt. % and 1600 °C.
- Open Access
- 20 October 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (5) , 549-555
Formation of non-metallic inclusions in production of 08Kh18N10T corrosion-resistant steel
Corrosion-resistant steels are in demand in the modern world due to their high performance properties and a wide range of applications. Such areas of application include kitchenware, furniture, medical equipment, nuclear reactors, spacecraft, etc. Oxygen in steel, especially in corrosion-resistant steel, is one of the most harmful elements. Oxide inclusions disrupt the homogeneity of the metal, negatively affect the ductility, fracture toughness, fatigue strength and corrosion resistance of steel. In corrosion-resistant steels, non-metallic inclusions (NI) lead to the formation of defects in cold-rolled sheets. Aluminate inclusions also lead to clogging of steel-casting equipment. An analysis of the production technology of corrosion-resistant steel 08Kh8N10T was carried out in order to determine the causes of NI formation that affect the pourability of steel and its quality. The studies determined the content of total oxygen and nitrogen, as well as oxygen bound in various non-metallic inclusions at the stages of ladle processing and continuous steel casting. It was shown that after the introduction of titanium wire into the melt, the total nitrogen content decreases due to the formation and subsequent removal of titanium nitrides. At the same time, the content of titanium oxides in the melt increases. It was shown that the causes of clogging of steel-pouring nozzles during continuous casting are complex non-metallic inclusions based on titanium oxides, which were deposited on the inner surface of the pouring nozzle-doser. Recommendations were made to adjust the technology of steel melting in EAF and ladle processing. Based on the results of electron microscopic analysis, it was established that mixing of refining liquid-mobile slag in ladle steel processing units contributed to the assimilation of non-metallic inclusions by slag and a decrease in their sizes in the metal. After the implementation of the corrective recommendations, clogging of steel-pouring nozzles during continuous casting was not observed.
- 20 October 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (5) , 549-555
Open AccessFormation of non-metallic inclusions in production of 08Kh18N10T corrosion-resistant steel
Corrosion-resistant steels are in demand in the modern world due to their high performance properties and a wide range of applications. Such areas of application include kitchenware, furniture, medical equipment, nuclear reactors, spacecraft, etc. Oxygen in steel, especially in corrosion-resistant steel, is one of the most harmful elements. Oxide inclusions disrupt the homogeneity of the metal, negatively affect the ductility, fracture toughness, fatigue strength and corrosion resistance of steel. In corrosion-resistant steels, non-metallic inclusions (NI) lead to the formation of defects in cold-rolled sheets. Aluminate inclusions also lead to clogging of steel-casting equipment. An analysis of the production technology of corrosion-resistant steel 08Kh8N10T was carried out in order to determine the causes of NI formation that affect the pourability of steel and its quality. The studies determined the content of total oxygen and nitrogen, as well as oxygen bound in various non-metallic inclusions at the stages of ladle processing and continuous steel casting. It was shown that after the introduction of titanium wire into the melt, the total nitrogen content decreases due to the formation and subsequent removal of titanium nitrides. At the same time, the content of titanium oxides in the melt increases. It was shown that the causes of clogging of steel-pouring nozzles during continuous casting are complex non-metallic inclusions based on titanium oxides, which were deposited on the inner surface of the pouring nozzle-doser. Recommendations were made to adjust the technology of steel melting in EAF and ladle processing. Based on the results of electron microscopic analysis, it was established that mixing of refining liquid-mobile slag in ladle steel processing units contributed to the assimilation of non-metallic inclusions by slag and a decrease in their sizes in the metal. After the implementation of the corrective recommendations, clogging of steel-pouring nozzles during continuous casting was not observed.
- Open Access
- 1 September 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (4) , 471-480
Development of a methodology for determining the content of non-metallic inclusions in steel
As part of the study, a method was proposed for assessing the metal purity for non-metallic inclusions using optical emission spectrometry. To assess the content of non-metallic inclusions in the slabs, two columns of metal were selected from two slabs of low-alloy metal deoxidized with aluminum. Each column was divided into seven samples in the direction from the small radius of the continuously cast ingot to the large one. We studied these samples to assess metal contamination with non-metallic inclusions using quantitative optical metallography according to ASTM E1245-03, fractional gas analysis (FGA) and optical emission spectral analysis PDA. Analysis of the samples according to ASTM E1245-03 standard showed that in all samples the percentage of oxides and sulfides is on average 10 and 90 %, respectively. According to the results of FGA, it was concluded that such non-metallic oxide inclusions as aluminates predominate in the metal samples of both ingots. A comparison was made between the results of the determination of oxygen in non-metallic inclusions obtained by FGA method and the number of sparks in inclusions at the analysis by PDA method; analysis of the dependencies showed that there are two clearly defined point distributions. To carry out PDA analysis, a program was developed that allows determining the number of inclusions of various types and calculate their volume fraction.
- 1 September 2024
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 67 (4) , 471-480
Open AccessDevelopment of a methodology for determining the content of non-metallic inclusions in steel
As part of the study, a method was proposed for assessing the metal purity for non-metallic inclusions using optical emission spectrometry. To assess the content of non-metallic inclusions in the slabs, two columns of metal were selected from two slabs of low-alloy metal deoxidized with aluminum. Each column was divided into seven samples in the direction from the small radius of the continuously cast ingot to the large one. We studied these samples to assess metal contamination with non-metallic inclusions using quantitative optical metallography according to ASTM E1245-03, fractional gas analysis (FGA) and optical emission spectral analysis PDA. Analysis of the samples according to ASTM E1245-03 standard showed that in all samples the percentage of oxides and sulfides is on average 10 and 90 %, respectively. According to the results of FGA, it was concluded that such non-metallic oxide inclusions as aluminates predominate in the metal samples of both ingots. A comparison was made between the results of the determination of oxygen in non-metallic inclusions obtained by FGA method and the number of sparks in inclusions at the analysis by PDA method; analysis of the dependencies showed that there are two clearly defined point distributions. To carry out PDA analysis, a program was developed that allows determining the number of inclusions of various types and calculate their volume fraction.
- 27 September 2021
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2021 (9) , 1135-1142
Analysis of the Process of Electrical Steel Production
The technology of melting and secondary processing of electrical silicon steel and the changes in the content of oxide nonmetallic inclusions (NIs) in the metal at the stages of its secondary processing and casting is analyzed. Fractional gas analysis and scanning electron microscopy with electron-probe microanalysis are used to study samples of three heats taken at the stages of secondary processing and casting of electrical silicon steel. The total oxygen and nitrogen content and the amount and the main types of oxide NIs (silicates, aluminosilicates, spinels) in the samples are determined. The increase in the amount of spinel NIs in the metal samples is assumed to be related to the influence of deoxidizers, and the increase in the oxygen and nitrogen content in the samples taken in a steel degassing plant and in a tundish during heat I can indicate the influence of secondary oxidation at these processing stages. Commercial heat logs are analyzed and thermodynamic calculations are performed in order to determine the factors affecting the destruction intensity of the steel-teeming ladle lining and the increase in the content of NIs and carbon in the metal samples.
- 27 September 2021
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2021 (9) , 1135-1142
Analysis of the Process of Electrical Steel Production
The technology of melting and secondary processing of electrical silicon steel and the changes in the content of oxide nonmetallic inclusions (NIs) in the metal at the stages of its secondary processing and casting is analyzed. Fractional gas analysis and scanning electron microscopy with electron-probe microanalysis are used to study samples of three heats taken at the stages of secondary processing and casting of electrical silicon steel. The total oxygen and nitrogen content and the amount and the main types of oxide NIs (silicates, aluminosilicates, spinels) in the samples are determined. The increase in the amount of spinel NIs in the metal samples is assumed to be related to the influence of deoxidizers, and the increase in the oxygen and nitrogen content in the samples taken in a steel degassing plant and in a tundish during heat I can indicate the influence of secondary oxidation at these processing stages. Commercial heat logs are analyzed and thermodynamic calculations are performed in order to determine the factors affecting the destruction intensity of the steel-teeming ladle lining and the increase in the content of NIs and carbon in the metal samples.
- Open Access
- 28 August 2021
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 64 (7) , 484-487
Interaction of rail steel melt with refractory lining
The rail steel properties are adversely affected by rigid non-metallic inclusions, containing aluminum oxides. Therefore, aluminum content is limited to 0.004 % wt. in rail steel grades. Aluminum can get into steel from charge materials and refractory lining. In this work, we’ve analyzed how the chemical composition of refractories used in rail steel making influence steel quality on example of one domestic enterprise. To determine the main types of non-metallic inclusions created in E76F rail steels, we have performed fractional gas analysis of the samples taken in various process steps. It was found that the slag composition after degassing changes insignificantly, while the most part of non-metallic inclusions in rail steel is represented by aluminates.
- 28 August 2021
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 64 (7) , 484-487
Open AccessInteraction of rail steel melt with refractory lining
The rail steel properties are adversely affected by rigid non-metallic inclusions, containing aluminum oxides. Therefore, aluminum content is limited to 0.004 % wt. in rail steel grades. Aluminum can get into steel from charge materials and refractory lining. In this work, we’ve analyzed how the chemical composition of refractories used in rail steel making influence steel quality on example of one domestic enterprise. To determine the main types of non-metallic inclusions created in E76F rail steels, we have performed fractional gas analysis of the samples taken in various process steps. It was found that the slag composition after degassing changes insignificantly, while the most part of non-metallic inclusions in rail steel is represented by aluminates.