Vladimir Panasenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vladimir Panasenko has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Musii Tseitlin
National Technical University “Kharkiv Polytechnic Institute
2 shared publications - Alona Dzevochko
National Technical University “Kharkiv Polytechnic Institute
1 shared publication - Anatolii Babichenko
National technical university «Kharkiv polytechnic institute
1 shared publication - Dmytro Snurnikov
National Technical University "Kharkiv Polytechnic Institute", Ukraine
1 shared publication - Igor Krasnikov
National technical university «Kharkiv polytechnic institute
1 shared publication - Inna Zabrodina
State Biotechnological University
1 shared publication
Latest Publications
- Open Access
- 30 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (6 (131)) , 6-14
Development of a complex antioxidant for stabilization of dressing enriched with omega-3 fatty acids
The solution to the problem of developing a complex antioxidant for the oxidative stabilization of emulsion systems with a high content of ω-3 polyunsaturated fatty acids (PUFAs) is considered. The object of the study is the oxidative stabilization of dressing using a complex antioxidant of plant origin. The ratio of ω-3:ω-6 PUFAs in model samples of the emulsion system was 1:5.46 and 1:2.21. The reasonable range of antioxidant ratios in the complex was substantiated. The ratio of tocopherol extract, garlic and laurel essential oils in the complex antioxidant is 1:1:1, respectively. Over 30 days of storage of the emulsion system model samples stabilized with a complex antioxidant, there is a gradual accumulation of organic acids (from 0.73 % to 0.75 %). The content of primary oxidation products increases for sample No. 2 – from 0.7 to 1.9 mmol ½ O2/kg, for sample No. 3 – from 0.4 to 1.2 mmol ½ O2/kg. The obtained values of physicochemical parameters meet the requirements of regulatory documentation (DSTU 4561). The peculiarity of the obtained results is that the complex antioxidant showed a significant increase in the stability of the emulsion system of high nutritional value, in particular, slowed down the accumulation of organic acids and peroxides. From a practical point of view, the development can effectively stabilize food emulsion systems with a high content of oxidation-labile PUFAs. An applied aspect of the obtained scientific result is the possibility of modeling and developing new formulations of emulsion and individual fat systems with high nutritional value, containing high PUFA concentrations
- 30 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (6 (131)) , 6-14
Open AccessDevelopment of a complex antioxidant for stabilization of dressing enriched with omega-3 fatty acids
The solution to the problem of developing a complex antioxidant for the oxidative stabilization of emulsion systems with a high content of ω-3 polyunsaturated fatty acids (PUFAs) is considered. The object of the study is the oxidative stabilization of dressing using a complex antioxidant of plant origin. The ratio of ω-3:ω-6 PUFAs in model samples of the emulsion system was 1:5.46 and 1:2.21. The reasonable range of antioxidant ratios in the complex was substantiated. The ratio of tocopherol extract, garlic and laurel essential oils in the complex antioxidant is 1:1:1, respectively. Over 30 days of storage of the emulsion system model samples stabilized with a complex antioxidant, there is a gradual accumulation of organic acids (from 0.73 % to 0.75 %). The content of primary oxidation products increases for sample No. 2 – from 0.7 to 1.9 mmol ½ O2/kg, for sample No. 3 – from 0.4 to 1.2 mmol ½ O2/kg. The obtained values of physicochemical parameters meet the requirements of regulatory documentation (DSTU 4561). The peculiarity of the obtained results is that the complex antioxidant showed a significant increase in the stability of the emulsion system of high nutritional value, in particular, slowed down the accumulation of organic acids and peroxides. From a practical point of view, the development can effectively stabilize food emulsion systems with a high content of oxidation-labile PUFAs. An applied aspect of the obtained scientific result is the possibility of modeling and developing new formulations of emulsion and individual fat systems with high nutritional value, containing high PUFA concentrations
- Open Access
- 28 February 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (2 (127)) , 74-81
Designing energy-efficient hardware and technological structure of absorption refrigeration units for ammonia production
The object of research is the equipment and technological design of absorption refrigeration units (ARUs) for the technological system of secondary condensation of large-scale ammonia production. Improving the energy efficiency of ARU is an urgent problem in the general process of reducing operating costs for natural gas in these industries as a whole. Based on the results of analytical studies, the feasibility of combining absorption-refrigeration and vapor-ejector cycles was substantiated, which ensures a decrease in the boiling temperature of a weak water-ammonia solution in the cube of the generator-rectifier and an increase in the condensation pressure in the ARU cycle. Under such circumstances, it becomes possible to increase the concentration of the refrigerant due to the rectification of steam with a part of the liquid refrigerant without using a pump with the removal of the dephlegmator from the ARU circuit. Experimental studies and material-thermal calculations of ARU cycles were carried out to determine the basis of comparison and the proposed version of the ARU scheme. It has been proven that the new technological design of ARU provides an increase in cooling capacity from 3.22 MW to 3.6 MW (by 12 %), the thermal coefficient from 0.527 to 0.551 (by 4.6 %), a decrease in the circulation ratio from 7.77 to 7.1 (by 8 %), and a decrease in the secondary condensation temperature by 2.5 ℃. It is shown that for the proposed version of the technological design of ARU, there is a change in specific costs – an increase in electricity by 1.48 kWh/t NH3 and a decrease in natural gas by 0.41 nm3/t NH3. Taking into account existing cost indicators for natural gas and electricity, the application of the proposed technology ensures a decrease in annual operating costs by UAH 7 million (USD 185,000), and therefore an increase in the economy of ammonia production as a whole Об’єктом досліджень є апаратурно-технологічне оформлення абсорбційно-холодильних установок (АХУ) технологічного комплексу вторинної конденсації великотоннажних виробництв аміаку. Підвищення енергоефективності АХУ становить актуальну проблему у загальному процесі зниження експлуатаційних витрат по природному газу цих виробництв в цілому. За результатами аналітичних досліджень обґрунтована доцільність поєднання абсорбційно-холодильного та пароежекторного циклів, що забезпечує зниження температури кипіння слабкого водоаміачного розчину в кубі генератора-ректифікатора та підвищення тиску конденсації в циклі АХУ. За таких обставин з'являється можливість збільшення концентрації холодоагенту за рахунок ректифікації пари частиною рідкого холодоагенту без застосування насосу із вилученням зі схеми АХУ дефлегматора. Проведено експериментальні дослідження та матеріально-теплові розрахунки циклів АХУ з визначенням бази порівняння та запропонованого варіанту схеми АХУ. Доведено, що нове технологічне оформлення АХУ забезпечує збільшення холодопродуктивності з 3,22 МВт до 3,6 МВт (на 12 %), теплового коефіцієнту з 0,527 до 0,551 (на 4,6 %), зниження кратності циркуляції з 7,77 до 7,1 (на 8 %) та зниження температури вторинної конденсації на 2,5 ℃. Показано, що для запропонованого варіанту технологічного оформлення АХУ спостерігається зміна питомих витрат – збільшення по електроенергії на 1,48 кВтгод/т NH3 та зниження по природному газу на 0,41 нм3/т.NH3. Враховуючи існуючі вартісні показники по природному газу і електроенергії застосування запропонованої технології забезпечує зниження річних експлуатаційних витрат на 7 млн грн.($185000), а отже і підвищення економічності виробництва аміаку в цілому
- 28 February 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (2 (127)) , 74-81
Open AccessDesigning energy-efficient hardware and technological structure of absorption refrigeration units for ammonia production
The object of research is the equipment and technological design of absorption refrigeration units (ARUs) for the technological system of secondary condensation of large-scale ammonia production. Improving the energy efficiency of ARU is an urgent problem in the general process of reducing operating costs for natural gas in these industries as a whole. Based on the results of analytical studies, the feasibility of combining absorption-refrigeration and vapor-ejector cycles was substantiated, which ensures a decrease in the boiling temperature of a weak water-ammonia solution in the cube of the generator-rectifier and an increase in the condensation pressure in the ARU cycle. Under such circumstances, it becomes possible to increase the concentration of the refrigerant due to the rectification of steam with a part of the liquid refrigerant without using a pump with the removal of the dephlegmator from the ARU circuit. Experimental studies and material-thermal calculations of ARU cycles were carried out to determine the basis of comparison and the proposed version of the ARU scheme. It has been proven that the new technological design of ARU provides an increase in cooling capacity from 3.22 MW to 3.6 MW (by 12 %), the thermal coefficient from 0.527 to 0.551 (by 4.6 %), a decrease in the circulation ratio from 7.77 to 7.1 (by 8 %), and a decrease in the secondary condensation temperature by 2.5 ℃. It is shown that for the proposed version of the technological design of ARU, there is a change in specific costs – an increase in electricity by 1.48 kWh/t NH3 and a decrease in natural gas by 0.41 nm3/t NH3. Taking into account existing cost indicators for natural gas and electricity, the application of the proposed technology ensures a decrease in annual operating costs by UAH 7 million (USD 185,000), and therefore an increase in the economy of ammonia production as a whole Об’єктом досліджень є апаратурно-технологічне оформлення абсорбційно-холодильних установок (АХУ) технологічного комплексу вторинної конденсації великотоннажних виробництв аміаку. Підвищення енергоефективності АХУ становить актуальну проблему у загальному процесі зниження експлуатаційних витрат по природному газу цих виробництв в цілому. За результатами аналітичних досліджень обґрунтована доцільність поєднання абсорбційно-холодильного та пароежекторного циклів, що забезпечує зниження температури кипіння слабкого водоаміачного розчину в кубі генератора-ректифікатора та підвищення тиску конденсації в циклі АХУ. За таких обставин з'являється можливість збільшення концентрації холодоагенту за рахунок ректифікації пари частиною рідкого холодоагенту без застосування насосу із вилученням зі схеми АХУ дефлегматора. Проведено експериментальні дослідження та матеріально-теплові розрахунки циклів АХУ з визначенням бази порівняння та запропонованого варіанту схеми АХУ. Доведено, що нове технологічне оформлення АХУ забезпечує збільшення холодопродуктивності з 3,22 МВт до 3,6 МВт (на 12 %), теплового коефіцієнту з 0,527 до 0,551 (на 4,6 %), зниження кратності циркуляції з 7,77 до 7,1 (на 8 %) та зниження температури вторинної конденсації на 2,5 ℃. Показано, що для запропонованого варіанту технологічного оформлення АХУ спостерігається зміна питомих витрат – збільшення по електроенергії на 1,48 кВтгод/т NH3 та зниження по природному газу на 0,41 нм3/т.NH3. Враховуючи існуючі вартісні показники по природному газу і електроенергії застосування запропонованої технології забезпечує зниження річних експлуатаційних витрат на 7 млн грн.($185000), а отже і підвищення економічності виробництва аміаку в цілому
- 25 May 2022
- Published by Springer Nature
- p. 177-186
Comparative Evaluation of the Contact Elements Efficiency for Barium Sulfide Solution Carbonization
- 25 May 2022
- Published by Springer Nature
- p. 177-186
Comparative Evaluation of the Contact Elements Efficiency for Barium Sulfide Solution Carbonization
- Open Access
- 21 January 2022
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 29 (4) , 549-558
ДОСЛІДЖЕННЯ ПРОЦЕСУ ОЧИЩЕННЯ СТІЧНИХ ВОД КОКСОХІМІЧНОГО ВИРОБНИЦТВА ГЛАУКОНІТОВОЮ ГЛИНОЮ
The process of complex purification of coke wastewater from phenols, rhodanides, ammonia, and resinous substances with the use of glauconite clay has been studied. Natural and activated glauconite, glauconite in combination with cationic flocculant brand Extraflock P 70, and activated carbon brand UAF (for comparison of cleaning efficiency) were used in this research. The activation of natural glauconite was carried out with a 7 % solution of HNO3 at 95–100 °C, at a ratio "mineral sorbent:acid solution" of 1:6 and an activation time of 5 hours It has been established that acid activation leads to a change in the chemical composition of glauconite and increases the specific surface area from 32 m2/g to 128 m2/g. Based on the results of natural glauconite thermal analysis, a conclusion was made about the phase transformations and chemical reactions that occur in glauconite clay during heating or cooling. Also, the thermal effects that accompany these changes, and some qualitative characteristics of the glauconite mineral were found. It was established that the maximum degree of phenols extraction from industrial effluent is up to 50% and is achieved when glauconite is used in combination with a flocculant. The maximum degree of purification from total ammonia is 57–58 % when using activated glauconite and glauconite with flocculant. The lowest degree of purification is achieved for rhodanides removal, not exceeding 20 % for any adsorbent. The highest degree of purification of 96.8 % is observed when removing resinous substances with glauconite in combination with a flocculant. Activation of glauconite by HNO3 leads to an increase in sorption capacity by 5–15 % depending on the pollutant. The coke wastewater purification degree of these pollutants with activated carbon is 20 % of phenols, 14 % of rhodanides, 28 % of total ammonia, and 72 % of resinous substances, respectively. Therefore, in industrial practice, it is recommended to use glauconite at a concentration of 2 g/dm3 in combination with 0.1 % solution of cationic flocculant with a volume of 30 cm3/dm3 with the duration of wastewater treatment 20–180 minutes for complex processing of effluents.
- 21 January 2022
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 29 (4) , 549-558
Open AccessДОСЛІДЖЕННЯ ПРОЦЕСУ ОЧИЩЕННЯ СТІЧНИХ ВОД КОКСОХІМІЧНОГО ВИРОБНИЦТВА ГЛАУКОНІТОВОЮ ГЛИНОЮ
The process of complex purification of coke wastewater from phenols, rhodanides, ammonia, and resinous substances with the use of glauconite clay has been studied. Natural and activated glauconite, glauconite in combination with cationic flocculant brand Extraflock P 70, and activated carbon brand UAF (for comparison of cleaning efficiency) were used in this research. The activation of natural glauconite was carried out with a 7 % solution of HNO3 at 95–100 °C, at a ratio "mineral sorbent:acid solution" of 1:6 and an activation time of 5 hours It has been established that acid activation leads to a change in the chemical composition of glauconite and increases the specific surface area from 32 m2/g to 128 m2/g. Based on the results of natural glauconite thermal analysis, a conclusion was made about the phase transformations and chemical reactions that occur in glauconite clay during heating or cooling. Also, the thermal effects that accompany these changes, and some qualitative characteristics of the glauconite mineral were found. It was established that the maximum degree of phenols extraction from industrial effluent is up to 50% and is achieved when glauconite is used in combination with a flocculant. The maximum degree of purification from total ammonia is 57–58 % when using activated glauconite and glauconite with flocculant. The lowest degree of purification is achieved for rhodanides removal, not exceeding 20 % for any adsorbent. The highest degree of purification of 96.8 % is observed when removing resinous substances with glauconite in combination with a flocculant. Activation of glauconite by HNO3 leads to an increase in sorption capacity by 5–15 % depending on the pollutant. The coke wastewater purification degree of these pollutants with activated carbon is 20 % of phenols, 14 % of rhodanides, 28 % of total ammonia, and 72 % of resinous substances, respectively. Therefore, in industrial practice, it is recommended to use glauconite at a concentration of 2 g/dm3 in combination with 0.1 % solution of cationic flocculant with a volume of 30 cm3/dm3 with the duration of wastewater treatment 20–180 minutes for complex processing of effluents.
- Open Access
- 21 December 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (114)) , 15-22
Construction of a mathematical model of the film absorber for sulfating two-component mixtures of organic substances
The processes that occur in film absorbers during the sulfation of two-component mixtures of organic substances are quite complex and require mathematical modeling. This paper reports the construction of a mathematical model that makes it possible to adequately describe the process of sulfation involving gaseous sulfur trioxide in the production of surfactants. Based on the model, it became possible to investigate this process for higher alcohols of fractions С12–С14 and monoethanolamides of higher fatty acids of coconut oil. The data are given on the comparison of mathematical modeling results based on the mathematical model built with known experimental data and results of alternative mathematical modeling for different ratios of the length of the reaction pipe to its diameter (l/d). It is shown that the error in comparing the experimental data was 4.8–9.6 % at l l/d=29; 1.1–8.7 % at l/d=70; 3.9–12.3 % at l/d=144. The error in comparing known results of alternative mathematical modeling was, respectively, 6.3–7.2 %, 0.1–6.5 %, 0–1.0 %. These results were obtained for the molar ratio in the range of 1.0–1.15 and the SO3 concentration in the stream of 4.0–6.0 %. Such findings suggest that the established dependences of the basic parameters for the sulfation process are adequate in terms of the absorber length and its radial direction. Therefore, the mathematical model built does hold within the considered ranges of input variables. Consequently, it could be used in the theoretical study of the process of sulfation of two-component mixtures of organic substances by gaseous sulfur trioxide in a film absorber with a downward flow of phases. The results obtained could be used in practice, in particular in the manufacture of high-quality products for the cosmetic industry.
- 21 December 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (114)) , 15-22
Open AccessConstruction of a mathematical model of the film absorber for sulfating two-component mixtures of organic substances
The processes that occur in film absorbers during the sulfation of two-component mixtures of organic substances are quite complex and require mathematical modeling. This paper reports the construction of a mathematical model that makes it possible to adequately describe the process of sulfation involving gaseous sulfur trioxide in the production of surfactants. Based on the model, it became possible to investigate this process for higher alcohols of fractions С12–С14 and monoethanolamides of higher fatty acids of coconut oil. The data are given on the comparison of mathematical modeling results based on the mathematical model built with known experimental data and results of alternative mathematical modeling for different ratios of the length of the reaction pipe to its diameter (l/d). It is shown that the error in comparing the experimental data was 4.8–9.6 % at l l/d=29; 1.1–8.7 % at l/d=70; 3.9–12.3 % at l/d=144. The error in comparing known results of alternative mathematical modeling was, respectively, 6.3–7.2 %, 0.1–6.5 %, 0–1.0 %. These results were obtained for the molar ratio in the range of 1.0–1.15 and the SO3 concentration in the stream of 4.0–6.0 %. Such findings suggest that the established dependences of the basic parameters for the sulfation process are adequate in terms of the absorber length and its radial direction. Therefore, the mathematical model built does hold within the considered ranges of input variables. Consequently, it could be used in the theoretical study of the process of sulfation of two-component mixtures of organic substances by gaseous sulfur trioxide in a film absorber with a downward flow of phases. The results obtained could be used in practice, in particular in the manufacture of high-quality products for the cosmetic industry.
- Open Access
- 30 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (10(112)) , 38-44
Defining features in the kinetics of sodium carbonate-bicarbonate solution carbonization and the quality of the resulting sodium bicarbonate crystals
This paper reports a study into the influence of temperature and gas consumption on the carbonization kinetics (saturation with carbon dioxide) of sodium carbonate-bicarbonate solution. The study also examined the quality and speed of crystal formation in this process. This research is predetermined by the environmental problems faced by modern enterprises that produce purified sodium bicarbonate – an insufficient degree of carbonization and, as a result, excessive air pollution with carbon dioxide, which did not participate in the reaction during the process. This study addresses these particular issues. As a result of using specialized laboratory equipment, it was found that an increase in the absorbent temperature from 79 to 85 °C leads to a decrease in the maximum degree of carbonization of the solution from 64 to 59 %. In contrast, the quality of the resulting sodium bicarbonate crystals improves but only in the range from 79 to 82 °C. With a further increase in temperature, the quality stabilizes. It is shown that the carbonization rate increases with increasing specific consumption of the absorbent (carbon dioxide) and is characterized by a negative correlation with the value of oversaturation of the absorbent in terms of NaНCO3. The quality of sodium bicarbonate crystals decreases with increasing gas velocity. Thus, it was reasonable to assume that the established dependence of the kinetics of carbonization of Na2CO3 and NaНCO3 solution on the gas velocity in the apparatus is explained by the inhibition of СО2 absorption, which is caused by the diffusion resistance of sodium bicarbonate crystallization. To improve the quality of crystals and the productivity of carbonization by reducing the supersaturation in terms of NaНCO3, it is recommended to introduce a seed crystal in the zone of binding of crystals in the carbonization columns.
- 30 August 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (10(112)) , 38-44
Open AccessDefining features in the kinetics of sodium carbonate-bicarbonate solution carbonization and the quality of the resulting sodium bicarbonate crystals
This paper reports a study into the influence of temperature and gas consumption on the carbonization kinetics (saturation with carbon dioxide) of sodium carbonate-bicarbonate solution. The study also examined the quality and speed of crystal formation in this process. This research is predetermined by the environmental problems faced by modern enterprises that produce purified sodium bicarbonate – an insufficient degree of carbonization and, as a result, excessive air pollution with carbon dioxide, which did not participate in the reaction during the process. This study addresses these particular issues. As a result of using specialized laboratory equipment, it was found that an increase in the absorbent temperature from 79 to 85 °C leads to a decrease in the maximum degree of carbonization of the solution from 64 to 59 %. In contrast, the quality of the resulting sodium bicarbonate crystals improves but only in the range from 79 to 82 °C. With a further increase in temperature, the quality stabilizes. It is shown that the carbonization rate increases with increasing specific consumption of the absorbent (carbon dioxide) and is characterized by a negative correlation with the value of oversaturation of the absorbent in terms of NaНCO3. The quality of sodium bicarbonate crystals decreases with increasing gas velocity. Thus, it was reasonable to assume that the established dependence of the kinetics of carbonization of Na2CO3 and NaНCO3 solution on the gas velocity in the apparatus is explained by the inhibition of СО2 absorption, which is caused by the diffusion resistance of sodium bicarbonate crystallization. To improve the quality of crystals and the productivity of carbonization by reducing the supersaturation in terms of NaНCO3, it is recommended to introduce a seed crystal in the zone of binding of crystals in the carbonization columns.