Simon Kammerloher
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Simon Kammerloher has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Wolfram Volk
Technische Universität München
3 shared publications - Julika Hoyer
Technical University of Munich
2 shared publications - Philipp Lechner
Technical University of Munich
2 shared publications - Ahmet Zahid Demirezen
RWTH Aachen University
1 shared publication - Aron Ringel
Institute of Metal Forming (IBF), RWTH Aachen University, Intzestraße 10, 52072 Aachen, Germany
1 shared publication - Benedikt Kirchebner
Chair of Metal Forming and Casting, Technical University of Munich, Walther-Meissner-Straße 4, 85748 Garching, Germany
1 shared publication
Latest Publications
- Open Access
- 8 September 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Development of novel hot-extruded Cu-ETP/CuZn37 composite rods
- 8 September 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Open AccessDevelopment of novel hot-extruded Cu-ETP/CuZn37 composite rods
- Open Access
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 55-68
Influences of the Rolling Parameters on Multi-Material Copper-Aluminum Composites via Compound Casting
Multi-material components that consist of copper and aluminum enable the combination of advantageous mechanical, thermal, and electrical properties at competitive cost. While roll bonding is an efficient-solid state joining technique, its implementation requires fully processed, cold-rolled strip material from two process routes. Continuous compound casting in contrast offers a more efficient approach by combining aluminum and copper during casting, followed by flat rolling in a single process route. However, the differences in flow stress between the metals can cause non-uniform elongation and therefore significant shear stresses at the interface during rolling. These stresses may lead to a delamination of the compound if process conditions are not well controlled. This study investigates whether a geometrically structured interface, introduced during compound casting, can contribute to withstanding interfacial shear stresses through mechanical interlocking. In finite element simulations varying process parameters including height reduction, initial temperature, rolling speed ratio, and pass schedule were examined. Results show that a structured interface can effectively resist shear stresses at the copper-aluminum boundary, thereby improving joint stability during deformation. Furthermore, the strain distribution as well as the fluctuation of the shear stresses can be controlled by the process parameters. The findings indicate that the mechanical interlocking by a geometric interface combined with optimized process parameters can enhance the rolling of compound-cast copper-aluminum composites.
- 15 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1185, 55-68
Open AccessInfluences of the Rolling Parameters on Multi-Material Copper-Aluminum Composites via Compound Casting
Multi-material components that consist of copper and aluminum enable the combination of advantageous mechanical, thermal, and electrical properties at competitive cost. While roll bonding is an efficient-solid state joining technique, its implementation requires fully processed, cold-rolled strip material from two process routes. Continuous compound casting in contrast offers a more efficient approach by combining aluminum and copper during casting, followed by flat rolling in a single process route. However, the differences in flow stress between the metals can cause non-uniform elongation and therefore significant shear stresses at the interface during rolling. These stresses may lead to a delamination of the compound if process conditions are not well controlled. This study investigates whether a geometrically structured interface, introduced during compound casting, can contribute to withstanding interfacial shear stresses through mechanical interlocking. In finite element simulations varying process parameters including height reduction, initial temperature, rolling speed ratio, and pass schedule were examined. Results show that a structured interface can effectively resist shear stresses at the copper-aluminum boundary, thereby improving joint stability during deformation. Furthermore, the strain distribution as well as the fluctuation of the shear stresses can be controlled by the process parameters. The findings indicate that the mechanical interlocking by a geometric interface combined with optimized process parameters can enhance the rolling of compound-cast copper-aluminum composites.
- Open Access
- 5 November 2023
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 18 (3) , 2467-2474
Binder Content and Storing Conditions of Inorganically-Bound Foundry Cores Determine the Intensity and Onset Time of Gas Release in Metal Casting
Organically-bound foundry cores are substituted by inorganically-bound cores increasingly. This trend is due to regulatory efforts, workplace safety issues, and increasing costs for waste deposits. Changing the binder system reduces the emissions to mostly water vapor, solving health and safety issues. Yet, the difference in the behavior of the gas phase, namely, the condensation potential of water, changes the casting process drastically. In contrast with the continuous generation and discharge of combustion products in the case of organic binders, water accumulates within the foundry core. Only once the cold spots of the core reach boiling temperature noteworthy amounts of vapor are created, increasing the chance for gas defects of the cast parts. Countermeasures have to be taken when designing the core’s geometry. We conducted the following research to improve the understanding of core gas release and its interactions with the foundry core’s binder content and storage conditions. Both binder content and relative humidity during storage were varied in three steps. Their influence on the core gas amount, time of gas generation, and gas permeability of the cores were investigated. The experiments were performed in the institute’s Induction Analysis Furnace and an aluminum melt bath. We found a strong dependency of storage humidity, further increased by increasing binder content on the gas amount and time of the gas release.
- 5 November 2023
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 18 (3) , 2467-2474
Open AccessBinder Content and Storing Conditions of Inorganically-Bound Foundry Cores Determine the Intensity and Onset Time of Gas Release in Metal Casting
Organically-bound foundry cores are substituted by inorganically-bound cores increasingly. This trend is due to regulatory efforts, workplace safety issues, and increasing costs for waste deposits. Changing the binder system reduces the emissions to mostly water vapor, solving health and safety issues. Yet, the difference in the behavior of the gas phase, namely, the condensation potential of water, changes the casting process drastically. In contrast with the continuous generation and discharge of combustion products in the case of organic binders, water accumulates within the foundry core. Only once the cold spots of the core reach boiling temperature noteworthy amounts of vapor are created, increasing the chance for gas defects of the cast parts. Countermeasures have to be taken when designing the core’s geometry. We conducted the following research to improve the understanding of core gas release and its interactions with the foundry core’s binder content and storage conditions. Both binder content and relative humidity during storage were varied in three steps. Their influence on the core gas amount, time of gas generation, and gas permeability of the cores were investigated. The experiments were performed in the institute’s Induction Analysis Furnace and an aluminum melt bath. We found a strong dependency of storage humidity, further increased by increasing binder content on the gas amount and time of the gas release.
- Open Access
A Method for Characterising the Influence of Casting Parameters on the Metallurgical Bonding of Copper and Steel Bimetals
Traditional casting technology offers two mayor drawbacks towards research activities. On the one hand, time and resources needed for every casting are rather high. The mould has to be able to withstand the high temperatures introduced by the melt and provide cooling for the cast part. Preparation and installation of measuring equipment therefore takes time. Additionally, due to the high mass of the mould when compared to the cast part, parameter variations are rather limited in their resulting effect on the temperature-time profile being one of the most prominent factors regarding cast quality. Especially when pouring by hand, variations in casting times and rates superimpose effects created intentionally. Therefore, a different process was advanced and evaluated, allowing to minimise some of the drawbacks mentioned before. The key idea is to drastically reduce casting size to the dimensions of one specimen and to apply a highly automated production route. As such, a mirror furnace was modified as to allow the processing of melt. Due to the specimens size, an adaption of mechanical testing equipment was performed and evaluated. As an example, copper-iron bimetal specimens were examined by light microscopy, micro hardness testing, nanoindentation as well as tensile and torsion testing. As the results were consistent, the newly introduced method can be applied successfully in casting research. This allows for highly reproducible results, reducing the uncertainty of temperature measurements of a specimen due to the distance between them. The possibility of separating influencing variables like maximum temperature and cooling rate allows an analysis of the casting process, which would require different moulds to do so in traditional casting methods. The next steps will be directed at a broader variety of metals processed and at a direct comparison between the new process route and traditional casting technology.
Open AccessA Method for Characterising the Influence of Casting Parameters on the Metallurgical Bonding of Copper and Steel Bimetals
Traditional casting technology offers two mayor drawbacks towards research activities. On the one hand, time and resources needed for every casting are rather high. The mould has to be able to withstand the high temperatures introduced by the melt and provide cooling for the cast part. Preparation and installation of measuring equipment therefore takes time. Additionally, due to the high mass of the mould when compared to the cast part, parameter variations are rather limited in their resulting effect on the temperature-time profile being one of the most prominent factors regarding cast quality. Especially when pouring by hand, variations in casting times and rates superimpose effects created intentionally. Therefore, a different process was advanced and evaluated, allowing to minimise some of the drawbacks mentioned before. The key idea is to drastically reduce casting size to the dimensions of one specimen and to apply a highly automated production route. As such, a mirror furnace was modified as to allow the processing of melt. Due to the specimens size, an adaption of mechanical testing equipment was performed and evaluated. As an example, copper-iron bimetal specimens were examined by light microscopy, micro hardness testing, nanoindentation as well as tensile and torsion testing. As the results were consistent, the newly introduced method can be applied successfully in casting research. This allows for highly reproducible results, reducing the uncertainty of temperature measurements of a specimen due to the distance between them. The possibility of separating influencing variables like maximum temperature and cooling rate allows an analysis of the casting process, which would require different moulds to do so in traditional casting methods. The next steps will be directed at a broader variety of metals processed and at a direct comparison between the new process route and traditional casting technology.