Wassila Boughamssa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Wassila Boughamssa has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Assia Abdelouahed
Department of Civil Engineering 20 Août1955 University of Skikda Skikda Algeria
2 shared publications - Ameur Belmouhoub
Department of Civil Engineering 20 Août1955 University of Skikda Skikda Algeria
1 shared publication Amira Afri
Department of Environmental Innovation and Eco‐Waste Management Division Environmental Research Center Annaba Algeria
1 shared publicationAmmar Noui
Department of Civil Engineering Mohamed Bachir El Ibrahimi University of Bordj Bou Arreridj Bordj Bou Arreridj Algeria
1 shared publicationHouria Hebhoub
1 shared publication- Leila Kherraf
Univ 20 Aout 1955, LMGHU Lab, Skikda, Algeria
1 shared publication
Latest Publications
- 6 November 2026
- Published by Wiley in Structural Concrete
Microstructural properties of ordinary concrete mixed with rubber and plastic waste under aggressive environmental conditions: A full‐factorial design study
The aim of this study was to incorporate the waste plastic and rubber into concrete in order to manufacture concrete that is resistant to aggressive environments, using the factorial approach to assess the effect of different factors (rubber and plastic) on the selected responses. In this research, ordinary Portland cement and fine aggregate were partially replaced with rubber and plastic as a mass substitute in the proportions of 2% and 4% and the fine aggregate 2%, 4%, and 6%, respectively. The tests used for the fresh properties were workability and density, whereas the hardened properties were assessed using compressive strength, flexural strength, and weight loss, as well as micro‐structural analysis, XRD, and scanning electron microscopy, SEM. The results show a decrease in workability, density, compressive strength, flexural strength, and weight loss when increasing the percentage of plastic and rubber used. The workability decreases from 80 to 20 mm, and the density decreases from 2.38 to 2.20 kg/m 3 ; the compressive and flexural strengths, respectively, decreased by up to 38% and 20.5% at 28 days compared to the control concrete. Moreover, the weight loss decreases by up to 25% compared to the control concrete. In addition, SEM indicated that the voids are filled with the waste rubber and plastic and thus reduce the penetration of sulfuric acid into the concrete. This helps maintain the integrity and durability of concrete in the face of aggressive environments. The test findings were subjected to analyses of variance in order to determine the significance of the influence factors and their interactions on the chosen responses. The results show that the coefficient R 2 ranges between 0.89 and 0.99, which indicates a good correlation between the predicted and experimental modes.
- 6 November 2026
- Published by Wiley in Structural Concrete
Microstructural properties of ordinary concrete mixed with rubber and plastic waste under aggressive environmental conditions: A full‐factorial design study
The aim of this study was to incorporate the waste plastic and rubber into concrete in order to manufacture concrete that is resistant to aggressive environments, using the factorial approach to assess the effect of different factors (rubber and plastic) on the selected responses. In this research, ordinary Portland cement and fine aggregate were partially replaced with rubber and plastic as a mass substitute in the proportions of 2% and 4% and the fine aggregate 2%, 4%, and 6%, respectively. The tests used for the fresh properties were workability and density, whereas the hardened properties were assessed using compressive strength, flexural strength, and weight loss, as well as micro‐structural analysis, XRD, and scanning electron microscopy, SEM. The results show a decrease in workability, density, compressive strength, flexural strength, and weight loss when increasing the percentage of plastic and rubber used. The workability decreases from 80 to 20 mm, and the density decreases from 2.38 to 2.20 kg/m 3 ; the compressive and flexural strengths, respectively, decreased by up to 38% and 20.5% at 28 days compared to the control concrete. Moreover, the weight loss decreases by up to 25% compared to the control concrete. In addition, SEM indicated that the voids are filled with the waste rubber and plastic and thus reduce the penetration of sulfuric acid into the concrete. This helps maintain the integrity and durability of concrete in the face of aggressive environments. The test findings were subjected to analyses of variance in order to determine the significance of the influence factors and their interactions on the chosen responses. The results show that the coefficient R 2 ranges between 0.89 and 0.99, which indicates a good correlation between the predicted and experimental modes.
- 1 January 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 45
Comparative study on the performance of sand-based mortars from marble, floor tile and cinder block waste
- 1 January 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 45
Comparative study on the performance of sand-based mortars from marble, floor tile and cinder block waste