DCDalong Cong

Dalong Cong

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dalong Cong has a total of 62 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Lightweight and anisotropic polyimide-based composite foams for efficient flame retardancy, thermal insulation and electromagnetic interference shielding applications

    by Long Ni, Caiyun Sun, Kongli Zhao, Jingjing Tang, Xuan Wang, Lingshu Dong, Xing Peng, Yinfu Luo, Dalong Cong, Daoxun Wu, et al.

  • Open Access

    Correction: Li et al. Study on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment. Coatings 2022, 12, 1611

    by Zhongsheng Li, Hulin Wu, Yixin Bai, Dalong Cong, Anwei Huang, Kaiqiang Song, Min Zhang, Zixiang Wei, Xingxing Ding, Xuan Wang, et al.

  • Open Access

    Evolution of Microstructure, Mechanical Properties and Residual Stress Prediction of Al2O3 Ceramic/TC4 Alloy Diffusion Bonded Joint

    by Yangfan Fu, Dalong Cong, Tao Hu, Guangjie Feng, Zhongsheng Li, Dajun Chen, Zaijun Yi, Guangyu Yu, Wei Cong, Yifeng Wang, et al.

    This study systematically investigates the microstructure evolution, mechanical properties, and residual stress distribution in diffusion-bonded joints between Al2O3 ceramic and TC4 alloy. Motivated by the need for reliable high-temperature joints in advanced applications, this work addresses the challenges posed by the materials’ physicochemical differences. Joints were fabricated at temperatures ranging from 800 °C to 950 °C under a pressure of 3 MPa for 2 h. Microstructural characterization revealed the formation of a multi-layered interfacial structure, dominated by a Ti3Al reaction layer, whose thickness increased with bonding temperature. The highest shear strength of 54 MPa was achieved at 850 °C, representing a key quantitative outcome of this parameter optimization. Beyond this temperature, excessive growth of the brittle Ti3Al layer and associated residual stresses led to strength degradation and interfacial cracking. A three-dimensional finite element model was developed to simulate residual stress distributions, highlighting significant tensile stresses within the Ti3Al layer and compressive stresses in the Al2O3 near the interface. The model further identified critical tensile stress concentrations along the vertical edges of the ceramic, which contribute to failure during shear testing.


  • Open Access

    Effect of Temperature Cycling Pretreatment on the Thermal Stability of Sm2(Co, Fe, Zr, Cu)17 Magnets in the Mild Temperature Range

    by Hulin Wu, Zhimei Long, Zhongsheng Li, Kaiqiang Song, Chaoqun Li, Dalong Cong, Bin Shao, Xiaowei Liu, Jianchun Sun, Yilong Ma

    The irredeemable magnetic losses of Sm(Co, Fe, Zr, Cu)7.8 permanent magnets caused by oxidation are very important for their practical application. In this work, the simulated results with R2 ≥ 98% based on the data of the temperature cycling test and the long-term isothermal test for the original samples confirmed that the magnetic flux losses reached 9.38% after the 5000th cycle in range R.T.–300 °C, and 7.15% after oxidated at 180 °C for 10 years, respectively. Demagnetization curves showed that the low-temperature oxidation mainly led to the remanence attenuation, while the coercivity remained relatively stable. SEM observation and EDS analysis revealed that an oxide outer layer with a thickness of 1.96 μm was formed on the surface of the original sample at 180 °C for 180 days, in which there was no enrichment or precipitation of metal elements. However, once a Cu, O-rich outer layer with a thickness of 0.72 μm was grown by using a temperature cycling from −50–250 °C for three cycles, the attenuation of magnetic properties could be inhibited under the low-temperature oxidation. This work suggested that the magnetic attenuation of Sm2Co17-type permanent magnets in the low-temperature field could not be ignored, and provided a simple method to suppress this attenuation of magnetic properties below 300 °C.


  • Open Access

    Study of Microstructure and Properties of Aluminum/Steel Inertia Radial Friction Welding

    by Zhongsheng Li, Zhengtao Liu, Dajun Chen, Fei Mo, Yangfan Fu, Ye Dai, Xia Wu, Dalong Cong

    In this paper, 6061-T6 aluminum alloy and 30CrMnSiA steel are bonded by inertia radial friction welding (IRFW). The formation mechanism of the aluminum/steel friction welded joints and the effect of the welding parameters on the mechanical properties are investigated through the microstructure, microzone composition, and mechanical property analysis. The results show that no visible intermetallic compound layers (IMCs) are detected on the aluminum/steel welding interface, which may be due to Si element aggregating in the welding interface and then forming a Al−Fe−Si phase, preventing the formation and growth of an Al−Fe IMCs. Eventually, a micron ultrathin interface reaction layer composed of Al0.7Fe3Si0.3, FeAl, and Fe3Al phases is formed at the aluminum/steel welding interface. The maximum average shear strength of the joint is 176 MPa. The shear fracture is a typical ductile fracture. Properly reducing the friction speed and increasing the upsetting pressure can improve the bonding strength of aluminum/steel joints.


  • Open Access

    Study on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment

    by Zhongsheng Li, Hulin Wu, Yixin Bai, Dalong Cong, Anwei Huang, Kaiqiang Song, Min Zhang, Zixiang Wei, Xingxing Ding, Xuan Wang, et al.

    In order to explore the corrosion damage behavior of plasma-sprayed NiCoCrAlY/magnesia-stabilized zirconia (18~22 wt.% MgO-ZrO2, MSZ) thermal barrier and anti-ablation coatings in a salt spray environment, a series of neutral salt spray (NSS) tests for 96 h (N-2), 192 h (N-4) and 288 h (N-6) were carried out on the coatings. The microstructures, composition distributions, potentiodynamic polarization curves, bonding strengths and anti-ablation properties of the coatings before and after the NSS tests were characterized. The results show that, with the increase in salt spray time, the expansion and overflow of corrosion products (FexOy) led to more defects forming inside the coating; the porosity of the top coat (TC) of N-6 increased to 15.2% in comparison to that of the blank control sample (N-0), which was 8.5%. According to the potentiodynamic polarization curves, accelerated corrosion occurred in the coating samples after the salt spray time reached 192 h, and the corrosion current density rapidly surged from 2.2 × 10−8 A·cm−2 (N-4) to 2.2 × 10−5 A·cm−2 (N-6). Similar degradation tends could be found in the bonding strengths and mass ablation rates of the coatings due to the accumulation of loose corrosion products on the substrate, which affected the bonding states of the coatings and promoted their spalling under an oxyacetylene flame (OAF). As a result, the maximum service life of the NiCoCrAlY/MSZ coatings in the neutral salt spray environment was about 192 h. This work is instructive for studying the environmental adaptability of metal/ceramic double-layer coatings.


  • Open Access

    The Effect of Temperature Cycling on the Magnetic Degradation and Microstructure of a Zn-Coated NdFeB Magnet

    by Hu-Lin Wu, Zhi-Mei Long, Kai-Qiang Song, Chao-Qun Li, Da-Long Cong, Bin Shao, Xiao-Wei Liu, Yi-Long Ma

    Temperature cycling tests in various temperature ranges were carried out to investigate the magnetic degradation of the Zn-coated NdFeB magnet. The losses of the surface magnetic field and magnetic flux were well fitted by using an index model. Compared with the lower limit temperature, the upper limit temperature had more obvious effect on the magnetic degradation. Once the upper limit temperature exceeded ≥160 °C, the magnetic degradation mainly occurred during the first cycle, which was different from the gradual decline with an increase in cycle number at a temperature of ≤140 °C. Moreover, the temperature cycling with a maximum upper limit temperature of 180 °C led to a loss of the remanence intensity, while the coercivity remained stable. Microstructure and element distribution analysis revealed that the oxidation of the Zn coating layer during the temperature cycling causes its cracking and an insertion of the oxygen element into the NdFeB substrate. The Nd-, Pr-rich phase at grain boundaries provided diffusion channels for oxygen elements, leading to a surface oxidation of NdFeB grains.


  • Effect of reinforcement particles on cold-sprayed Al-based coatings

    by Zhongsheng Li, Hulin Wu, Xingxing Ding, Kaiqiang Song, Min Zhang, Li Li, Anwei Huang, Dalong Cong

    In this study, malleable and heavy Ta particles were introduced into soft Al powders to prepare Al-Ta composite coatings through a low-pressure cold-spray process; for comparison, Al-A2O3 composite coatings were also deposited. The surface and cross-sectional morphologies, deposition efficiency, microstructure, hardness and composition of the coatings were investigated. The results demonstrated that the Al-Ta coatings had roughness values that were almost twice as large as those of the Al-Al2O3 coatings for the same volumetric fraction of reinforcement particles used in the feedstock. Ta particles were more effective in improving the deposition efficiency and densification than were Al2O3 particles. The formation mechanism of the Al-Ta coatings was mainly attributed to the malleable and heavy nature of Ta particles, which allowed them to bond with the formed coating and impact the coating strongly through the peening effect.


  • Open Access

    Effects of Additives Containing Cyanopyridine on Electrodeposition of Bright Al Coatings from AlCl3-EMIC Ionic Liquids

    by Min Zhang, Dong Peng, Feifei Peng, Anwei Huang, Kaiqiang Song, Qingbing He, Changqing Yin, Jinsong Rao, Yuxin Zhang, Haitao Chen, et al.

    The Al coatings were electrodeposited on the Cu substrate from AlCl3-EMIC ionic liquid (AlCl3:EMIC = 2:1 molar ratio) containing three cyanopyridine additives with different positions of the substituent group on the pyridine ring, which were 2-cyanopyridine, 3-cyanopyridine, and 4-cyanopyridine. The effects of cyanopyridine additives on the deposition potential, morphology, brightness, and corrosion properties of Al coatings were investigated. It was considered that the deposition potential of Al shifted to more negative overpotentials, the quality of Al coatings was promoted, and the corrosion property was improved by the cyanopyridine additives to a varying degree. Especially in the presence of 4-cyanopyridine, the flattest mirror bright Al coating was obtained, which had the smallest homogeneous nanocrystal grain size and strongest Al (200) crystallographic orientation. The average roughness Ra value was as low as 31 nm compared to that in the absence of cyanopyridine additives, which was 417 nm. Furthermore, the corrosion current density of the bright Al coating was three orders of magnitude lower than the rough Al coating, which resulted from the dense nanocrystal structure.


  • Open Access

    Active Corrosion Protection of Mg–Al Layered Double Hydroxide for Magnesium Alloys: A Short Review

    by Xinfang Zhang, Min Zhang, Ruihong Li, Xiaoyan Feng, Xue Pang, Jinsong Rao, Dalong Cong, Changqing Yin, Yuxin Zhang

    Layered double hydroxides (LDHs) have been successfully applied in surface protection and functionalization of metal materials owing to their special structure, composition, controllability, anion exchange, and other excellent properties. Herein, this review focused on the most common LDH preparation methods on magnesium alloys in the past 10 years by summarizing about 70 research papers. At the same time, based on the corrosion protection mechanism of LDH materials, the performance of LDH films and LDH as filler on metal substrates was briefly introduced. The surface of LDH materials were chemically modified to enhance their compatibility with solvents, and their corrosion resistance function was developed as an additive. Finally, LDH-based composite coatings on Mg alloys by surface pretreatment and chemical modification were discussed.