MZMin Zhang

Min Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Min Zhang has a total of 25 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Resin Precursor Solid Content on the Properties of Fiber-Reinforced Phenolic-Resin Aerogel Composites

    by Yixin Bai, Kaiqiang Song, Xuan Wang, Lei Yu, Anwei Huang, Jianchao Huang, Qingbing He, Dong Peng, Min Zhang, Zhongsheng Li

    Lightweight fiber-reinforced phenolic-resin aerogel (NF/PRA) composites are key ablation thermal protection materials for hypersonic vehicles. However, how resin precursor solid content governs the complete processing–structure–property chain, particularly the multi-mode mechanical behavior and high-heat-flux ablation performance, remains poorly understood. In this study, high-silica fiber/phenolic-resin aerogel composites with different contents of a novolac resin precursor (15%, H15S15; 20%, H15S20; 25%, H15S25; 30%, H15S30) were fabricated via vacuum-assisted resin transfer molding combined with atmospheric-pressure drying, and were systematically characterized in terms of their microstructure, mechanical properties, thermophysical behavior, thermal insulation, and ablation resistance. A higher solid content created a denser three-dimensional nano-network in the PRA matrix, decreasing the average pore size from 75.4 to 37.4 nm and increasing the bulk density from 0.299 to 0.458 g/cm3. The abundant mesopores led to ultra-low thermal conductivities of 0.039–0.042 W/(m·K). The compressive, flexural, and shear strengths increased monotonically with the solid content, whereas the tensile strength peaked at 18.03 MPa for H15S25 and declined at higher contents owing to matrix brittleness. Notably, a higher solid content synergistically enhanced both thermal insulation and ablation resistance. After oxyacetylene flame ablation, the linear ablation rate of H15S30 was 32.7% lower than that of H15S15, and the back-face temperature was more than 58% lower. Post-ablation microstructural observations revealed a three-stage mechanism involving pyrolytic carbonization, fiber melting, and mechanical scouring, in which layer-by-layer spallation of the amorphous carbon and SiO2-rich molten phases governs the damage. This study provides guidance for optimizing the processing–structure–property relationship of NF/PRA composites for ablation thermal protection applications.

  • Open Access

    Correction: Li et al. Study on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment. Coatings 2022, 12, 1611

    by Zhongsheng Li, Hulin Wu, Yixin Bai, Dalong Cong, Anwei Huang, Kaiqiang Song, Min Zhang, Zixiang Wei, Xingxing Ding, Xuan Wang, et al.

  • Open Access

    Study on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment

    by Zhongsheng Li, Hulin Wu, Yixin Bai, Dalong Cong, Anwei Huang, Kaiqiang Song, Min Zhang, Zixiang Wei, Xingxing Ding, Xuan Wang, et al.

    In order to explore the corrosion damage behavior of plasma-sprayed NiCoCrAlY/magnesia-stabilized zirconia (18~22 wt.% MgO-ZrO2, MSZ) thermal barrier and anti-ablation coatings in a salt spray environment, a series of neutral salt spray (NSS) tests for 96 h (N-2), 192 h (N-4) and 288 h (N-6) were carried out on the coatings. The microstructures, composition distributions, potentiodynamic polarization curves, bonding strengths and anti-ablation properties of the coatings before and after the NSS tests were characterized. The results show that, with the increase in salt spray time, the expansion and overflow of corrosion products (FexOy) led to more defects forming inside the coating; the porosity of the top coat (TC) of N-6 increased to 15.2% in comparison to that of the blank control sample (N-0), which was 8.5%. According to the potentiodynamic polarization curves, accelerated corrosion occurred in the coating samples after the salt spray time reached 192 h, and the corrosion current density rapidly surged from 2.2 × 10−8 A·cm−2 (N-4) to 2.2 × 10−5 A·cm−2 (N-6). Similar degradation tends could be found in the bonding strengths and mass ablation rates of the coatings due to the accumulation of loose corrosion products on the substrate, which affected the bonding states of the coatings and promoted their spalling under an oxyacetylene flame (OAF). As a result, the maximum service life of the NiCoCrAlY/MSZ coatings in the neutral salt spray environment was about 192 h. This work is instructive for studying the environmental adaptability of metal/ceramic double-layer coatings.


  • Open Access

    Effects of Additives Containing Cyanopyridine on Electrodeposition of Bright Al Coatings from AlCl3-EMIC Ionic Liquids

    by Min Zhang, Dong Peng, Feifei Peng, Anwei Huang, Kaiqiang Song, Qingbing He, Changqing Yin, Jinsong Rao, Yuxin Zhang, Haitao Chen, et al.

    The Al coatings were electrodeposited on the Cu substrate from AlCl3-EMIC ionic liquid (AlCl3:EMIC = 2:1 molar ratio) containing three cyanopyridine additives with different positions of the substituent group on the pyridine ring, which were 2-cyanopyridine, 3-cyanopyridine, and 4-cyanopyridine. The effects of cyanopyridine additives on the deposition potential, morphology, brightness, and corrosion properties of Al coatings were investigated. It was considered that the deposition potential of Al shifted to more negative overpotentials, the quality of Al coatings was promoted, and the corrosion property was improved by the cyanopyridine additives to a varying degree. Especially in the presence of 4-cyanopyridine, the flattest mirror bright Al coating was obtained, which had the smallest homogeneous nanocrystal grain size and strongest Al (200) crystallographic orientation. The average roughness Ra value was as low as 31 nm compared to that in the absence of cyanopyridine additives, which was 417 nm. Furthermore, the corrosion current density of the bright Al coating was three orders of magnitude lower than the rough Al coating, which resulted from the dense nanocrystal structure.


  • Open Access

    Active Corrosion Protection of Mg–Al Layered Double Hydroxide for Magnesium Alloys: A Short Review

    by Xinfang Zhang, Min Zhang, Ruihong Li, Xiaoyan Feng, Xue Pang, Jinsong Rao, Dalong Cong, Changqing Yin, Yuxin Zhang

    Layered double hydroxides (LDHs) have been successfully applied in surface protection and functionalization of metal materials owing to their special structure, composition, controllability, anion exchange, and other excellent properties. Herein, this review focused on the most common LDH preparation methods on magnesium alloys in the past 10 years by summarizing about 70 research papers. At the same time, based on the corrosion protection mechanism of LDH materials, the performance of LDH films and LDH as filler on metal substrates was briefly introduced. The surface of LDH materials were chemically modified to enhance their compatibility with solvents, and their corrosion resistance function was developed as an additive. Finally, LDH-based composite coatings on Mg alloys by surface pretreatment and chemical modification were discussed.


  • Open Access

    Mirror-like Bright Al-Mn Coatings Electrodeposition from 1-Ethyl-3 Methylimidazolium Chloride-AlCl3-MnCl2 Ionic Liquids with Pyridine Derivatives

    by Dong Peng, Dalong Cong, Kaiqiang Song, Xingxing Ding, Xuan Wang, Yixin Bai, Xinrui Yang, Changqing Yin, Yuxin Zhang, Jinsong Rao, et al.

    The effects of three pyridine derivative additives, 4-hydroxypyridine, 4-picolinic acid, and 4-cyanopyridine, on Al-Mn coatings were investigated in 1-ethyl-3-methylimidazolium chloride-AlCl3-MnCl2 (EMIC-AlCl3-MnCl2) ionic liquids. The smooth mirror-like bright Al-Mn coatings were obtained only in the EMIC-AlCl3-MnCl2 ionic liquids containing 4-cyanopyridine, while the matte Al-Mn coatings were electrodeposited from EMIC-AlCl3-MnCl2 without additives or containing either 4-hydroxypyridine or 4-picolinic acid. The scanning electron microscope and X-ray diffraction showed that the bright Al-Mn coatings consisted of nanocrystals and had a strong (200) preferential orientation, while the particle size of matte Al-Mn coatings were within the micron range. The brightening mechanism of 4-cyanopyridine is due to it being adsorbed onto the cathode to produce the combined effect of (1) generating an overpotential to promote Al-Mn nucleation; (2) inhibiting the growth of the deposited nuclei and enabling them grow preferentially, making the coating composed of nanocrystals and with a smooth surface. The brightening effect of 4-cyanopyridine on the Al-Mn coatings was far better than that of the 4-hydroxypyridine and the 4-picolinic acid. In addition, the bright Al-Mn coating was prepared in a bath with 6 mmol·L−1 4-cyanopyridine and displayed superior corrosion resistance relative to the matte coatings, which could be attributed to its unique nanocrystalline structure that increased the number of grain boundaries and accelerated the formation of the protective layer of the corrosion products.