Anwei Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anwei Huang has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Zhongsheng Li
Southwest Institute of Technology and Engineering, Chongqing 400039, China
5 shared publications - Dalong Cong
Southwest Institute of Technology and Engineering, Chongqing 400039, China
4 shared publications - Kaiqiang Song
Southwest Institute of Technology and Engineering, Chongqing 400039, China
4 shared publications - Min Zhang
Southwest Institute of Technology and Engineering, Chongqing 400039, China
4 shared publications - Dong Peng
Southwest Institute of Technology and Engineering, Chongqing 400039, China
3 shared publications - Yixin Bai
Southwest Institute of Technology and Engineering, Chongqing 400039, China
3 shared publications
Latest Publications
- Open Access
- 9 November 2026
- Published by Springer Nature in Thermal Functional Materials
- Vol. 1 (1) , 12
Lightweight and anisotropic polyimide-based composite foams for efficient flame retardancy, thermal insulation and electromagnetic interference shielding applications
- 9 November 2026
- Published by Springer Nature in Thermal Functional Materials
- Vol. 1 (1) , 12
Open AccessLightweight and anisotropic polyimide-based composite foams for efficient flame retardancy, thermal insulation and electromagnetic interference shielding applications
- Open Access
- 30 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (17) , 8626
Effect of Resin Precursor Solid Content on the Properties of Fiber-Reinforced Phenolic-Resin Aerogel Composites
Lightweight fiber-reinforced phenolic-resin aerogel (NF/PRA) composites are key ablation thermal protection materials for hypersonic vehicles. However, how resin precursor solid content governs the complete processing–structure–property chain, particularly the multi-mode mechanical behavior and high-heat-flux ablation performance, remains poorly understood. In this study, high-silica fiber/phenolic-resin aerogel composites with different contents of a novolac resin precursor (15%, H15S15; 20%, H15S20; 25%, H15S25; 30%, H15S30) were fabricated via vacuum-assisted resin transfer molding combined with atmospheric-pressure drying, and were systematically characterized in terms of their microstructure, mechanical properties, thermophysical behavior, thermal insulation, and ablation resistance. A higher solid content created a denser three-dimensional nano-network in the PRA matrix, decreasing the average pore size from 75.4 to 37.4 nm and increasing the bulk density from 0.299 to 0.458 g/cm3. The abundant mesopores led to ultra-low thermal conductivities of 0.039–0.042 W/(m·K). The compressive, flexural, and shear strengths increased monotonically with the solid content, whereas the tensile strength peaked at 18.03 MPa for H15S25 and declined at higher contents owing to matrix brittleness. Notably, a higher solid content synergistically enhanced both thermal insulation and ablation resistance. After oxyacetylene flame ablation, the linear ablation rate of H15S30 was 32.7% lower than that of H15S15, and the back-face temperature was more than 58% lower. Post-ablation microstructural observations revealed a three-stage mechanism involving pyrolytic carbonization, fiber melting, and mechanical scouring, in which layer-by-layer spallation of the amorphous carbon and SiO2-rich molten phases governs the damage. This study provides guidance for optimizing the processing–structure–property relationship of NF/PRA composites for ablation thermal protection applications.
- 30 August 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (17) , 8626
Open AccessEffect of Resin Precursor Solid Content on the Properties of Fiber-Reinforced Phenolic-Resin Aerogel Composites
Lightweight fiber-reinforced phenolic-resin aerogel (NF/PRA) composites are key ablation thermal protection materials for hypersonic vehicles. However, how resin precursor solid content governs the complete processing–structure–property chain, particularly the multi-mode mechanical behavior and high-heat-flux ablation performance, remains poorly understood. In this study, high-silica fiber/phenolic-resin aerogel composites with different contents of a novolac resin precursor (15%, H15S15; 20%, H15S20; 25%, H15S25; 30%, H15S30) were fabricated via vacuum-assisted resin transfer molding combined with atmospheric-pressure drying, and were systematically characterized in terms of their microstructure, mechanical properties, thermophysical behavior, thermal insulation, and ablation resistance. A higher solid content created a denser three-dimensional nano-network in the PRA matrix, decreasing the average pore size from 75.4 to 37.4 nm and increasing the bulk density from 0.299 to 0.458 g/cm3. The abundant mesopores led to ultra-low thermal conductivities of 0.039–0.042 W/(m·K). The compressive, flexural, and shear strengths increased monotonically with the solid content, whereas the tensile strength peaked at 18.03 MPa for H15S25 and declined at higher contents owing to matrix brittleness. Notably, a higher solid content synergistically enhanced both thermal insulation and ablation resistance. After oxyacetylene flame ablation, the linear ablation rate of H15S30 was 32.7% lower than that of H15S15, and the back-face temperature was more than 58% lower. Post-ablation microstructural observations revealed a three-stage mechanism involving pyrolytic carbonization, fiber melting, and mechanical scouring, in which layer-by-layer spallation of the amorphous carbon and SiO2-rich molten phases governs the damage. This study provides guidance for optimizing the processing–structure–property relationship of NF/PRA composites for ablation thermal protection applications.
- Open Access
Study on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment
In order to explore the corrosion damage behavior of plasma-sprayed NiCoCrAlY/magnesia-stabilized zirconia (18~22 wt.% MgO-ZrO2, MSZ) thermal barrier and anti-ablation coatings in a salt spray environment, a series of neutral salt spray (NSS) tests for 96 h (N-2), 192 h (N-4) and 288 h (N-6) were carried out on the coatings. The microstructures, composition distributions, potentiodynamic polarization curves, bonding strengths and anti-ablation properties of the coatings before and after the NSS tests were characterized. The results show that, with the increase in salt spray time, the expansion and overflow of corrosion products (FexOy) led to more defects forming inside the coating; the porosity of the top coat (TC) of N-6 increased to 15.2% in comparison to that of the blank control sample (N-0), which was 8.5%. According to the potentiodynamic polarization curves, accelerated corrosion occurred in the coating samples after the salt spray time reached 192 h, and the corrosion current density rapidly surged from 2.2 × 10−8 A·cm−2 (N-4) to 2.2 × 10−5 A·cm−2 (N-6). Similar degradation tends could be found in the bonding strengths and mass ablation rates of the coatings due to the accumulation of loose corrosion products on the substrate, which affected the bonding states of the coatings and promoted their spalling under an oxyacetylene flame (OAF). As a result, the maximum service life of the NiCoCrAlY/MSZ coatings in the neutral salt spray environment was about 192 h. This work is instructive for studying the environmental adaptability of metal/ceramic double-layer coatings.
Open AccessStudy on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment
In order to explore the corrosion damage behavior of plasma-sprayed NiCoCrAlY/magnesia-stabilized zirconia (18~22 wt.% MgO-ZrO2, MSZ) thermal barrier and anti-ablation coatings in a salt spray environment, a series of neutral salt spray (NSS) tests for 96 h (N-2), 192 h (N-4) and 288 h (N-6) were carried out on the coatings. The microstructures, composition distributions, potentiodynamic polarization curves, bonding strengths and anti-ablation properties of the coatings before and after the NSS tests were characterized. The results show that, with the increase in salt spray time, the expansion and overflow of corrosion products (FexOy) led to more defects forming inside the coating; the porosity of the top coat (TC) of N-6 increased to 15.2% in comparison to that of the blank control sample (N-0), which was 8.5%. According to the potentiodynamic polarization curves, accelerated corrosion occurred in the coating samples after the salt spray time reached 192 h, and the corrosion current density rapidly surged from 2.2 × 10−8 A·cm−2 (N-4) to 2.2 × 10−5 A·cm−2 (N-6). Similar degradation tends could be found in the bonding strengths and mass ablation rates of the coatings due to the accumulation of loose corrosion products on the substrate, which affected the bonding states of the coatings and promoted their spalling under an oxyacetylene flame (OAF). As a result, the maximum service life of the NiCoCrAlY/MSZ coatings in the neutral salt spray environment was about 192 h. This work is instructive for studying the environmental adaptability of metal/ceramic double-layer coatings.
- Open Access
Effects of Additives Containing Cyanopyridine on Electrodeposition of Bright Al Coatings from AlCl3-EMIC Ionic Liquids
The Al coatings were electrodeposited on the Cu substrate from AlCl3-EMIC ionic liquid (AlCl3:EMIC = 2:1 molar ratio) containing three cyanopyridine additives with different positions of the substituent group on the pyridine ring, which were 2-cyanopyridine, 3-cyanopyridine, and 4-cyanopyridine. The effects of cyanopyridine additives on the deposition potential, morphology, brightness, and corrosion properties of Al coatings were investigated. It was considered that the deposition potential of Al shifted to more negative overpotentials, the quality of Al coatings was promoted, and the corrosion property was improved by the cyanopyridine additives to a varying degree. Especially in the presence of 4-cyanopyridine, the flattest mirror bright Al coating was obtained, which had the smallest homogeneous nanocrystal grain size and strongest Al (200) crystallographic orientation. The average roughness Ra value was as low as 31 nm compared to that in the absence of cyanopyridine additives, which was 417 nm. Furthermore, the corrosion current density of the bright Al coating was three orders of magnitude lower than the rough Al coating, which resulted from the dense nanocrystal structure.
Open AccessEffects of Additives Containing Cyanopyridine on Electrodeposition of Bright Al Coatings from AlCl3-EMIC Ionic Liquids
The Al coatings were electrodeposited on the Cu substrate from AlCl3-EMIC ionic liquid (AlCl3:EMIC = 2:1 molar ratio) containing three cyanopyridine additives with different positions of the substituent group on the pyridine ring, which were 2-cyanopyridine, 3-cyanopyridine, and 4-cyanopyridine. The effects of cyanopyridine additives on the deposition potential, morphology, brightness, and corrosion properties of Al coatings were investigated. It was considered that the deposition potential of Al shifted to more negative overpotentials, the quality of Al coatings was promoted, and the corrosion property was improved by the cyanopyridine additives to a varying degree. Especially in the presence of 4-cyanopyridine, the flattest mirror bright Al coating was obtained, which had the smallest homogeneous nanocrystal grain size and strongest Al (200) crystallographic orientation. The average roughness Ra value was as low as 31 nm compared to that in the absence of cyanopyridine additives, which was 417 nm. Furthermore, the corrosion current density of the bright Al coating was three orders of magnitude lower than the rough Al coating, which resulted from the dense nanocrystal structure.