ADAhmad Daniar

Ahmad Daniar

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ahmad Daniar has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Interleaved Dual Three-Phase Machine Interturn Short-Circuit Fault Mitigation Topology Using Current Source Inverter Drive

    by Hadi S. Ismail, Ahmad Daniar, Matthew C. Gardner

    Many types of short circuit faults may occur in electric machines, due to winding insulation failure. The interturn fault is one of the most insidious types, especially in surface permanent magnet synchronous machines (SPMSM). This article evaluates a method to reduce the fault current caused by a short between two adjacent turns. We interleave turns from dual three-phase windings, which do not share a common neutral point. This causes a short circuit between any two adjacent turns to become a phase-to-phase short circuit, and the fault current must pass through the motor terminals. Dual three-phase current source inverters, each having the dc link inductance split between the positive and negative sides, have been used to greatly reduce this fault current so that the machine can continue running with a minimal penalty in performance. By using the dc link inductors of the dual three-phase current source inverters, this fault current mitigation is achieved passively and without the need for additional components. This approach was evaluated in simulation and experimentally. For the motor evaluated, the measured fault current was limited to 15.2% of the rated current.


  • Active Fault Current Mitigation With Multi-Phase Inverter and Windings for Resilience Against Short-Circuit Faults Between Adjacent Turns

    by Ahmad Daniar, Matthew C. Gardner, Rahman Sajadi, Salek A. Khan

    This paper presents an active fault mitigation technique in response to a short-circuit fault between adjacent turns in electric machines. The proposed technique is demonstrated using a six-phase inverter, differential mode chokes (DMCs), and a dual three-phase interleaved winding arrangement. With this arrangement, a short circuit fault between adjacent turns becomes a phase-to-phase fault. Thus, the fault current no longer circulates only inside the motor; instead, it passes through motor terminals and can easily be measured. Then, a fault current mitigation control loop (FCMCL) is added to the field oriented control (FOC) algorithm to adjust the voltages applied to the affected phases to reduce the fault current. When a fault current is detected, the FCMCL injects a zero-sequence voltage in one of the three-phase sets. Using this method, the fault current is reduced to less than 4% of the rated current, allowing the machine to continue its operation almost completely close to normal conditions in the presence of fault. This 4% is an order of magnitude smaller than the 42% achieved with the baseline passive implementation involving only DMCs and a three-phase inverter. Close agreement between simulation and experimental results validates the effectiveness and accuracy of the proposed method.


  • An Outer Rotor Surface PM Motor With Integrated Chokes for Fault-Tolerant Operation in the Presence of Short-Circuit Faults Between Adjacent Turns

    by Ahmad Daniar, Salek A. Khan, Matthew C. Gardner

    This paper presents a novel design for an outer rotor surface permanent magnet (SPM) machine intended to enhance fault tolerance in the presence of short-circuit faults between adjacent turns. The proposed motor configuration employs a dual three-phase winding arrangement, wherein two distinct sets of three-phase windings have separate neutral points and are galvanically isolated from each other. The turns within each slot are interleaved to ensure that adjacent turns do not belong to the same phase or to phases that share a common neutral point. This strategic arrangement effectively transforms inter-turn short-circuit faults into phase-to-phase faults, forcing fault currents to pass through the machine’s terminals. To further mitigate fault currents, the design incorporates differential mode chokes (DMC) within the stator. For a prototype motor, a DMC inductance of 255 μH was achieved without compromising the motor’s torque. With the integrated DMC, the fault current was reduced from 25.9 A to 2.65 A, and the experimental results agree well with the simulation results.


  • Open Access

    Magnetic Equivalent Circuit Model for Performance Prediction of Two-DOF Planar Resolver

    by Fateme Zare, Farid Tootoonchian, Ahmad Daniar, Matthew C. Gardner, Bilal Akin

    In this paper, an analytical model based on the Magnetic Equivalent Circuit (MEC) method is developed for a planar wound mover two-degree of freedom (2-DOF) resolver. Planar resolvers enable mass, volume, and complexity reductions for position control of 2-DOF linear actuators. However, similar to any other linear electromagnetic sensors, the performance of the planar resolvers is negatively affected by the limited dimensions of the mover’s ferromagnetic core. Thus, it is necessary to develop an appropriate compensation method. On the other hand, the 3-D geometry of the sensor necessitates extremely time consuming 3-D time-stepping analysis. Therefore, a fast yet accurate analytical model is critical for the iterative design and compensation algorithm. In order to address these modeling limitations, the slot-tooth region and longitudinal end effect are included in the model. Then, its accuracy is verified by comparing the results with those of the 3-D time stepping finite element method (TSFEM). Then, the developed model is employed for design optimization to compensate for the end effects. Finally, the optimal sensor is experimentally prototyped and tested.


  • Comprehensive Investigation of the Resolver’s Eccentricity Effect on the Field-Oriented Control of PMSM

    by M. S. KhajueeZadeh, M. Emadaleslami, F. Tootoonchian, A. Daniar, M. C. Gardner, B. Akin

    Accurate position feedback from a resolver is highly critical for high-performance field-oriented control (FOC) drives, and eccentricity in resolvers negatively affects the drive performance. The current unbalance intensity (CUI) of permanent magnet synchronous motors (PMSM) is a known criterion to evaluate drive stability and can be caused by position feedback error. In this paper, the eccentric resolver operation is comprehensively investigated, and the corresponding CUI is analytically evaluated. Accordingly, the error limit is defined for an acceptable operation under eccentricity without derating the motor control. For this purpose, the relationship between the (a) resolver’s physical geometry, (b) magnitude and the angle of the stator current, and (c) resolver accuracy are presented through surrogate modeling. Using the proposed analytical current model, the resolver geometry is updated in order to improve the eccentricity tolerance and accuracy and lower the CUI. An optimized rotor design is built, and its accuracy and effect on CUI mitigation are experimentally verified.


  • A Passive Inter Turn Short Circuit Fault Mitigation Technique for Electric Machines

    by Ahmad Daniar, Salek A. Khan, Matthew C. Gardner

    This paper proposes a passive inter turn short circuit current mitigation technique that adds differential mode chokes (DMCs) between the inverter and the phase pairs in a multiphase winding arrangement. The fault current manifests itself as a differential mode current between faulted phases, and this paper shows that the DMCs can reduce the fault current, while the DMCs only slightly affect the common mode or healthy current. The amplitude of the fault current reduction depends on the DMC size. This study shows that a 200 $\mu$ H DMC can reduce the fault current by multiple orders of magnitude from 4586% (without DMCs) to 10% of the rated current for a simulated permanent magnet synchronous machine. With that level of fault current mitigation, the machine can continue operating almost normally. A setup based on transformers cores was built and tested. The experimental results show that, with a 65 $\mu$ H DMC, the fault current is reduced from 120% to less than 1% of the rated current. The good agreement between simulation and experimental results validates the model.


  • Electromagnetic Design Characterization of a Dual Rotor Axial Flux Motor for Electric Aircraft

    by Dorsa Talebi, Matthew C. Gardner, Sri Vignesh Sankarraman, Ahmad Daniar, Hamid A. Toliyat

    This paper presents and evaluates a dual rotor axial flux permanent magnet motor for electric aircraft applications. Several features, including grain oriented electrical steel, Halbach arrays, and wires with rectangular cross-sections, are used to improve torque density and efficiency. A novel winding arrangement is used to mitigate interturn short-circuit faults. Rather than simply optimizing the motor by itself, this paper evaluates the tradeoffs between motor performance and its interfaces with the drive, thermal management system (TMS), and mechanical structure. This information can be used along with similar analyses of these subsystems to select the design with the system-level optimal performance. The paper uses finite element simulations to characterize tradeoffs between active mass, efficiency, fundamental frequency, power factor, axial forces on the rotors, and cooling surface area. Several designs exceed 95% efficiency at takeoff with less than 8 kg of active mass. While high pole counts, a large outer radius, and short stator teeth tend to optimize the magnetic performance at takeoff, this can reduce cruise efficiency, reduce the surface area through which the TMS can extract heat, increase the fundamental frequency the drive must supply, increase the structural mass required to support the rotors, and introduce complexity to manufacturing process. Further analysis for a selected design reveals that the power factor can be significantly improved with a minimal torque penalty via field weakening, due to significant saturation in the stator teeth.


  • Accurate and Fast Subdomain Model for Electromagnetic Design Purpose of Wound-Field Linear Resolver

    by Ayub Paymozd, Hamid Saneie, Ahmad Daniar, Zahra Nasiri-Gheidari

    Linear resolvers are position sensors that are being used in a wide range of applications for linear motion systems. The electromagnetic design of a linear resolver, similar to any other electromagnetic device, demands an accurate, functional, and fast tool. While the finite element method (FEM) is considered the most accurate tool for electromagnetic analysis, it is not a good candidate for an optimization-based design which is an iterative process. In this article, first off, an analytical tool based on the subdomain model is briefly presented. This model is very accurate and much faster than FEM. However, it has high computational time for iterative design and optimization processes. Therefore, in the second step, simplification assumptions are utilized to make the model even faster without compromising the accuracy of the model. In this regard, model numbers 1-4 are developed and then compared to each other in terms of computational time and accuracy. Time stepping FEM (TSFEM) is employed as the reference for comparison between different models. A prototype of the linear resolver is then fabricated to show the validity of the study. Close agreement between simulations and experimental results demonstrates the competency of the study.


  • Simplified Winding Arrangement for Integrated Multiturn Resolvers

    by Hamid Saneie, Zahra Nasiri-Gheidari, Farid Tootoonchian, Ahmad Daniar

    Winding configuration is a crucial factor that highly affects the accuracy of resolvers. A nonoptimal winding could also make the manufacturing process complicated and costly inefficient. In this article, an approach to determine the optimal winding configuration for the resolvers is proposed. This method is applicable for both wound rotor (WR) and variable reluctance (VR) resolvers, and significantly simplifies the winding configuration of resolvers with different pole pairs and teeth numbers. Based on the proposed approach, the winding configuration of multiturn resolvers, which are generally more complicated than single-turn resolvers, is simplified for WR and VR type resolver with different number of stator teeth. In this approach, the reliability of the sensor is also considered. The proposed winding facilitates the manufacturing process and decreases the production costs for the multiturn resolver. The three-dimensional time-stepping finite-element method is used to confirm the correctness of the analysis. Finally, a prototype of the sensor is built and tested to verify the validity of the proposed winding approach. The measured value of the average of absolute position error for 1X/5X resolver is 0.197°/0.081°, and the maximum position error is 0.716°/0.212°.


  • Performance Analysis of Linear Variable Reluctance Resolvers Based on an Improved Winding Function Approach

    by Ahmad Daniar, Zahra Nasiri-Gheidari, Farid Tootoonchian

    Linear Variable Reluctance (LVR) resolvers have substantial benefits that make them suitable for linear motion control drives. The optimal design of LVR resolvers needs an accurate modelling that is usually achieved by three-dimensional (3-D) time stepping finite element method (TSFEM). However, 3-D TSFEM is very time consuming method and is unsuitable for co-usage with optimization algorithms. So, in this paper an accurate analytical model based on improved winding function (IWF) method is proposed. The proposed model is used to calculate the inductances, air-gap flux density, induced voltages and linear position error. The distinguished feature of the proposed model is direct usage of the turn function in calculating the inductances. While, the conventional modified winding function (MWF) method uses the Fourier Seri of the turn function. So, the proposed model is much faster and more accurate than the models based on conventional MWF method. The results of the proposed model are verified with those of 3-D TSFEM. Then, the proposed model is used for design optimization of the sensor. Also, two methods are proposed for compensating the longitudinal end effect. Finally, the experimental prototype is used to evaluate the developed analytical model and the optimization process.