EFEric Fabris

Eric Fabris

*This is an algorithmically generated author record based on publicly available information.

Eric Fabris has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Two-Feedback Loop Shunt Regulator Based on PWM RF Power Detector Aiming RFID Applications

    by Rafael Cantalice, Fernando Paixao Cortes, Eric Ericson Fabris, Sandro Binsfeld Ferreira, Hamilton Klimach

    The paper presents a novel shunt voltage regulation architecture that uses an RF power detector, based on Pulse Width Modulation (PWM) technique, aiming at magnetic coupled Radio-Frequency Identification (RFID) transponders. The proposed regulator architecture implements two feedback loops: a voltage clamping circuit that composes a fast correction loop and a slow but accurate power detector loop. The first clamping loop guarantees fast over-voltage protection, mainly in high RF power condition (short reading distance), but degrades power efficiency when in low power condition (large reading distance). The second loop corrects the imprecision of the first loop according to the detected RF input power. Therefore, it increases power efficiency and reading distance when in low RF power condition. The RF power detector architecture, based on a PWM technique, and the shunt regulator design are presented and discussed in detail. RFID power regulation issues are also discussed, followed by a brief review of RF power detector circuits. The complete regulator architecture was implemented in a 180nm CMOS low cost process and prototyped as part of a commercial low-frequency (134 kHz) RFID transponder. The complete transponder area is 870 $\times $ 870 $\mu \text{m}^{2}$ , being 130 $\times $ 230 $\mu \text{m}^{2}$ related to the regulator circuit only. Both resonant and supply capacitors are implemented on chip. The analog and digital functional blocks of the RFID system consume 4.5 $\mu \text{W}$ . Performance of the transponder is measured with the shunt regulator enabled and compared with the power limiting approach using only clamping diodes. Measured results show an improvement of 16.7% in the maximum communication distance between the transponder and the reader because of the proposed regulation strategy.


  • Non-Linear Shunt Regulator With RF Power Detector for RFID Applications

    by Rafael Cantalice, Fernando Paixao Cortes, Eric Fabris, Sandro Binsfeld Ferreira, Hamilton Klimach

    This paper presents a non-linear shunt regulator based on a PWM RF power detector for RFID applications. The shunt regulator is composed of two feedback loops. The first is a fast loop based on a simple RF voltage clamp that guarantees overvoltage protection for the internal circuits. The second is an accurate loop based on a power detector circuit that slowly corrects the first loop errors according to the input RF power. The theoretical formulation of the RF-to-DC conversion in the power detector is presented and compared to a high-level implementation. A small-signal model of the complete shunt regulator was developed to assist in the CMOS circuit design. The regulator is part of a commercial low-frequency RFID transponder. It shows an improvement of 16.7 % in the maximum communication distance of the transponder with the shunt regulator enabled when compared to the previous power limiting approach using only clamping diodes.


  • 1.5 ppm/°C nano-Watt resistorless MOS-only voltage reference

    by C. Jhon A. Gomez, Hamilton Klimach, Eric Fabris, Sergio Bampi

    This paper presents a MOS-only high power supply rejection (PSRR) voltage reference with a very low temperature coefficient (TC) that consumes only tens of nano-Watt. It is composed by a threshold voltage monitor circuit with no resistors, cascaded with a thermal voltage generator, adequate for fabrication in standard processes. Since the MOS transistors operate in subthreshold and near-threshold regimes the current consumption is very low. The operation of the circuit is analytically described and a design methodology is proposed. Post-layout simulations for a design in a 130 nm CMOS process are presented, resulting a reference voltage around 670 mV with a best case TC of 1.5 ppm/°C for the -40 to +125 °C range and an average TC of 20 ppm/°C over process variations, untrimmed. A very low sensitivity to V DD is achieved, resulting a PSRR lower than -71 dB at 100 Hz and a line sensitivity (LS) lower than 576 ppm/V for a supply range from 1 to 3 V. The area is very small, 0.0084 mm2 including the start-up stage.


  • Open Access

    MOSFET ZTC Condition Analysis for a Self-biased Current Reference Design

    by Pedro Toledo, Hamilton Klimach, David Cordova, Sergio Bampi, Eric Fabris

    In this paper a self-biased current reference based on Metal-Oxide-Semiconductor Field Effect Transistor (MOSFET) Zero Temperature Coefficient (ZTC) condition is proposed. It can be implemented in any Complementary Metal-Oxide-Semiconductor (CMOS) fabrication process and provides another alternative to design current references. In order to support the circuit design, ZTC condition is analyzed using a MOSFET model that is continuous from weak to strong inversion, showing that this condition always occurs from moderate to strong inversion in any CMOS process. The proposed topology was designed in a 180 nm process, operates with a supply voltage from 1.4V to 1.8 V and occupies around 0.010mm2 of silicon area. From circuit simulations our reference showed a temperature coefficient (TC) of 15 ppm/oC from -40 to +85oC, and a fabrication process sensitivity of σ/μ = 4.5% for the current reference, including average process and local mismatch variability analysis. The simulated power supply sensitivity is estimated around 1%/V.