Sirintornthep Towprayoon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sirintornthep Towprayoon has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Komsilp Wangyao
The Joint Graduate School of Energy and Environment, King Mongkut’s University of Technology Thonburi, Bangkok, Thailand
8 shared publications - Awassada Phongphiphat
The Joint Graduate School of Energy and Environment, King Mongkut’s University of Technology Thonburi, Bangmod, Thungkru, Bangkok, Thailand
6 shared publications - Suthum Patumsawad
Department of Mechanical and Aerospace Engineering, Faculty of Engineering, King Mongkut’s University of Technology North Bangkok, Bangkok 10800, Thailand
6 shared publications - Chart Chiemchaisri
Department of Environmental Engineering, Faculty of Engineering, Kasetsart University, Bangkok, Thailand
5 shared publications - Noppharit Sutthasil
School of Health Science, Mae Fah Luang University, Chiang Rai 57100, Thailand
3 shared publications - Abhisit Bhatsada
The Joint Graduate School of Energy and Environment (JGSEE), King Mongkut's University of Technology Thonburi, Bangkok, Thailand
2 shared publications
Latest Publications
- 2 June 2025
- Published by Elsevier in Bioresource Technology Reports
- Vol. 30
Optimizing wet-refuse derived fuel 3 for enhanced energy recovery: A biodrying approach
- 2 June 2025
- Published by Elsevier in Bioresource Technology Reports
- Vol. 30
Optimizing wet-refuse derived fuel 3 for enhanced energy recovery: A biodrying approach
- Open Access
Exploring Refuse-Derived Fuel Production from Seafood-Processing Sludge and Landfill-Mined Plastic Waste Co-Pelletization
This study explores the co-pelletization of sludge with landfill-mined plastic waste as a method to create high-energy refuse-derived fuel (RDF), addressing both plastic and sludge waste streams. Key variables used in RDF pelletization included sludge-to-plastic mixing ratios (50:50, 75:25, and 100:0 wt%), mold temperatures (100 °C and 120 °C), and compression pressures (60–80 MPa). Results showed that the characteristics of pellets improved considerably as the mass percentage of plastic waste increased. The 75% sludge mixture produced pellets with high compressive strength (15.9–16.4 MPa), indicating rigid and ductile properties, and achieved a calorific value of up to 33.4 MJ/kg. Mercury levels of the RDF (0.02–0.04 mg/MJ) met solid recovered fuel standards. However, the elevated chlorine content (>3 wt%db) highlighted the necessity of removing PVC from the plastic waste before pelletization. Carbon emission factors for the pellets (23–25 kg CO2/GJ) were comparable to commercial RDFs and notably lower than coal, demonstrating their potential as a sustainable alternative fuel source. An assessment of the entire production and utilization chain, including sludge drying, plastic sorting, pelletization, and combustion, revealed that co-pelletization reduces greenhouse gas emissions by more than 24.3% compared to current practices.
Open AccessExploring Refuse-Derived Fuel Production from Seafood-Processing Sludge and Landfill-Mined Plastic Waste Co-Pelletization
This study explores the co-pelletization of sludge with landfill-mined plastic waste as a method to create high-energy refuse-derived fuel (RDF), addressing both plastic and sludge waste streams. Key variables used in RDF pelletization included sludge-to-plastic mixing ratios (50:50, 75:25, and 100:0 wt%), mold temperatures (100 °C and 120 °C), and compression pressures (60–80 MPa). Results showed that the characteristics of pellets improved considerably as the mass percentage of plastic waste increased. The 75% sludge mixture produced pellets with high compressive strength (15.9–16.4 MPa), indicating rigid and ductile properties, and achieved a calorific value of up to 33.4 MJ/kg. Mercury levels of the RDF (0.02–0.04 mg/MJ) met solid recovered fuel standards. However, the elevated chlorine content (>3 wt%db) highlighted the necessity of removing PVC from the plastic waste before pelletization. Carbon emission factors for the pellets (23–25 kg CO2/GJ) were comparable to commercial RDFs and notably lower than coal, demonstrating their potential as a sustainable alternative fuel source. An assessment of the entire production and utilization chain, including sludge drying, plastic sorting, pelletization, and combustion, revealed that co-pelletization reduces greenhouse gas emissions by more than 24.3% compared to current practices.
- Open Access
- 20 December 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (24) , 11181
Enhanced Landfill Mining in Thailand: Policy Implications from Qualitative Case Study Analysis
Limited landfill capacity and increasing waste production present obstacles for the management of municipal solid waste (MSW) in Thailand, where 7.1 million tons of MSW were non-sanitarily managed in 2022. This provides an opportunity for the nation to recover valuable materials and energy from landfill waste through excavation by implementing the enhanced landfill mining technique, which is consistent with business sustainability goals. This study evaluates regulatory, financial, and institutional challenges to enhanced landfill mining implementation, identifying key barriers such as Thailand’s restriction on using refuse-derived fuel (RDF) in waste-to-energy (WtE) projects, despite its higher calorific value (18–24 MJ/kg compared to 13.7–16.6 MJ/kg for fresh MSW-derived RDF). Case studies, particularly from European nations, are comparatively evaluated using a combination of qualitative analysis methods. The results of this study highlight that the potential of enhanced landfill mining in Thailand is restricted by the prohibition of the use of RDF in WtE projects, as well as a lack of financial incentives to follow existing regulations. This demonstrates that the implementation of enhanced landfill mining could be facilitated by changing Thai regulations to permit the use of RDF in WtE projects and providing financial incentives such as tax credits and feed-in tariffs. Implementing such reforms can help Thailand achieve its sustainability objectives while reducing the amount of waste in landfills and generating energy.
- 20 December 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (24) , 11181
Open AccessEnhanced Landfill Mining in Thailand: Policy Implications from Qualitative Case Study Analysis
Limited landfill capacity and increasing waste production present obstacles for the management of municipal solid waste (MSW) in Thailand, where 7.1 million tons of MSW were non-sanitarily managed in 2022. This provides an opportunity for the nation to recover valuable materials and energy from landfill waste through excavation by implementing the enhanced landfill mining technique, which is consistent with business sustainability goals. This study evaluates regulatory, financial, and institutional challenges to enhanced landfill mining implementation, identifying key barriers such as Thailand’s restriction on using refuse-derived fuel (RDF) in waste-to-energy (WtE) projects, despite its higher calorific value (18–24 MJ/kg compared to 13.7–16.6 MJ/kg for fresh MSW-derived RDF). Case studies, particularly from European nations, are comparatively evaluated using a combination of qualitative analysis methods. The results of this study highlight that the potential of enhanced landfill mining in Thailand is restricted by the prohibition of the use of RDF in WtE projects, as well as a lack of financial incentives to follow existing regulations. This demonstrates that the implementation of enhanced landfill mining could be facilitated by changing Thai regulations to permit the use of RDF in WtE projects and providing financial incentives such as tax credits and feed-in tariffs. Implementing such reforms can help Thailand achieve its sustainability objectives while reducing the amount of waste in landfills and generating energy.
- Open Access
- 20 November 2024
- Published by MDPI AG in Clean Technologies
- Vol. 6 (4) , 1519-1536
Aeration Optimization for the Biodrying of Market Waste Using Negative Ventilation: A Lysimeter Study
This study investigates the optimization of aeration rates for the biodrying of market waste using negative-pressure ventilation. Market waste, characterized by a high moisture content (MC) and rapid decomposition, presents challenges in waste management. Over 12 days, three aeration rates (ARs) of 0.2, 0.4, and 0.6 m3/kg/day were examined, and the most effective continuous ventilation configuration was identified in terms of heat generation, moisture reduction, and biodrying efficiency. The results indicate that the most effective AR for heat retention and moisture removal was 0.2 m3/kg/day, achieving a 6.63% MC reduction and a 9.12% low heating value (LHV) increase. Gas analysis showed that, while AR 0.2 supported high microbial activity during the initial 7 days, AR 0.6 sustained higher overall CO2 production due to its greater aeration rate. The findings also suggest that the biodrying of market waste with a high initial MC can achieve significant weight loss and leachate generation when paired with a high aeration rate of 0.6 m3/kg/day, with a 69.8% weight loss and increased waste compaction being recorded. The study suggests that variable ARs can optimize biodrying, making market waste more suitable for conversion to refuse-derived fuel or landfill pre-treatment and improving waste-to-energy processes and sustainability.
- 20 November 2024
- Published by MDPI AG in Clean Technologies
- Vol. 6 (4) , 1519-1536
Open AccessAeration Optimization for the Biodrying of Market Waste Using Negative Ventilation: A Lysimeter Study
This study investigates the optimization of aeration rates for the biodrying of market waste using negative-pressure ventilation. Market waste, characterized by a high moisture content (MC) and rapid decomposition, presents challenges in waste management. Over 12 days, three aeration rates (ARs) of 0.2, 0.4, and 0.6 m3/kg/day were examined, and the most effective continuous ventilation configuration was identified in terms of heat generation, moisture reduction, and biodrying efficiency. The results indicate that the most effective AR for heat retention and moisture removal was 0.2 m3/kg/day, achieving a 6.63% MC reduction and a 9.12% low heating value (LHV) increase. Gas analysis showed that, while AR 0.2 supported high microbial activity during the initial 7 days, AR 0.6 sustained higher overall CO2 production due to its greater aeration rate. The findings also suggest that the biodrying of market waste with a high initial MC can achieve significant weight loss and leachate generation when paired with a high aeration rate of 0.6 m3/kg/day, with a 69.8% weight loss and increased waste compaction being recorded. The study suggests that variable ARs can optimize biodrying, making market waste more suitable for conversion to refuse-derived fuel or landfill pre-treatment and improving waste-to-energy processes and sustainability.
- Open Access
- 5 August 2024
- Published by Center of Biomass and Renewable Energy Scientia Academy in International Journal of Renewable Energy Development
- Vol. 13 (5) , 941-951
Optimizing aeration rates via bio-methane potential test for enhanced biodrying efficiency of refuse-derived fuel-3
Aeration forms a critical part of the biodrying of refuse-derived fuel-3 (RDF-3) and significantly affects the fuel’s energy potential. Understanding the organic content (OC) of RDF-3 is crucial for determining the optimal aeration strategy. In this study, we conducted a bio-methane potential (BMP) test to estimate the OC by observing the conversion of organic matter into methane (CH₄) and carbon dioxide (CO₂). The observation of BMP was conducted using anaerobic digestion approach where substrate and inoculum are important parameters considered for the success of this test. Various ratios substrate-to-inoculum (S/I) were explored to assess their impact on biogas production, our research involved testing four S/I ratios (0.25, 0.5, 1.0, and 1.5) focusing on identifying the optimal aeration strategy. Based on stoichiometric calculations, the sample’s biogas yield per gram volatile solid indicates RDF-3’s OC is 1.5%. This OC value played a role in establishing the appropriate aeration rate (AR) for the biodrying process, which was determined to be 0.6 m³/kg.day, indicating the action of effective microbial degradation processes. Ensuring the correct AR is vital for maximizing the energy potential of RDF-3. Implementing optimized aeration rates based on the BMP test in waste management practices can significantly improve RDF-3 biodrying efficiency. This approach enhances RDF quality, reduces moisture, increases calorific value, and minimizes greenhouse gas emissions, leading to more sustainable and efficient waste-to-energy conversion.
- 5 August 2024
- Published by Center of Biomass and Renewable Energy Scientia Academy in International Journal of Renewable Energy Development
- Vol. 13 (5) , 941-951
Open AccessOptimizing aeration rates via bio-methane potential test for enhanced biodrying efficiency of refuse-derived fuel-3
Aeration forms a critical part of the biodrying of refuse-derived fuel-3 (RDF-3) and significantly affects the fuel’s energy potential. Understanding the organic content (OC) of RDF-3 is crucial for determining the optimal aeration strategy. In this study, we conducted a bio-methane potential (BMP) test to estimate the OC by observing the conversion of organic matter into methane (CH₄) and carbon dioxide (CO₂). The observation of BMP was conducted using anaerobic digestion approach where substrate and inoculum are important parameters considered for the success of this test. Various ratios substrate-to-inoculum (S/I) were explored to assess their impact on biogas production, our research involved testing four S/I ratios (0.25, 0.5, 1.0, and 1.5) focusing on identifying the optimal aeration strategy. Based on stoichiometric calculations, the sample’s biogas yield per gram volatile solid indicates RDF-3’s OC is 1.5%. This OC value played a role in establishing the appropriate aeration rate (AR) for the biodrying process, which was determined to be 0.6 m³/kg.day, indicating the action of effective microbial degradation processes. Ensuring the correct AR is vital for maximizing the energy potential of RDF-3. Implementing optimized aeration rates based on the BMP test in waste management practices can significantly improve RDF-3 biodrying efficiency. This approach enhances RDF quality, reduces moisture, increases calorific value, and minimizes greenhouse gas emissions, leading to more sustainable and efficient waste-to-energy conversion.
- Open Access
- 4 January 2024
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 33 (3) , 2307-2315
Performance Comparison between Anaerobic Hybrid Reactor and Anaerobic Continuous Stirred-Tank Reactor for High-Strength Fresh Leachate Treatment
This study aimed to examine the performance of an anaerobic hybrid reactor (AHR) and an anaerobic continuous stirred tank reactor (CSTR) for treating high-strength fresh leachate. As the organic loading rate (OLR) was increased in both systems, the pH decreased, with the lowest pH corresponding to an OLR of 25-30 kgCOD/m3·d. The AHR system demonstrated instability in total volatile fatty acids when the OLR increased to 20 kgCOD/m3·d. The highest methane (CH4) content was achieved when the OLR was 15 kgCOD/m3·d. Moreover, the AHR showed excellent sediment retention. When the OLR increased, volatile suspended solids (VSS) in the system increased. The CH4 content tended to increase as the OLR increased up to 20 kgCOD/m3·d. The highest CH4 content in the AHR was 68%, which was higher than that of the CSTR. The CSTR could not produce biogas when the OLR was 20 kgCOD/m3·d. The optimal OLR for the operation of AHR and CSTR treating fresh leachate was found to be 15 and 10 kgCOD/m3·d respectively.
- 4 January 2024
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 33 (3) , 2307-2315
Open AccessPerformance Comparison between Anaerobic Hybrid Reactor and Anaerobic Continuous Stirred-Tank Reactor for High-Strength Fresh Leachate Treatment
This study aimed to examine the performance of an anaerobic hybrid reactor (AHR) and an anaerobic continuous stirred tank reactor (CSTR) for treating high-strength fresh leachate. As the organic loading rate (OLR) was increased in both systems, the pH decreased, with the lowest pH corresponding to an OLR of 25-30 kgCOD/m3·d. The AHR system demonstrated instability in total volatile fatty acids when the OLR increased to 20 kgCOD/m3·d. The highest methane (CH4) content was achieved when the OLR was 15 kgCOD/m3·d. Moreover, the AHR showed excellent sediment retention. When the OLR increased, volatile suspended solids (VSS) in the system increased. The CH4 content tended to increase as the OLR increased up to 20 kgCOD/m3·d. The highest CH4 content in the AHR was 68%, which was higher than that of the CSTR. The CSTR could not produce biogas when the OLR was 20 kgCOD/m3·d. The optimal OLR for the operation of AHR and CSTR treating fresh leachate was found to be 15 and 10 kgCOD/m3·d respectively.
- Open Access
- 20 October 2023
- Published by Center of Biomass and Renewable Energy Scientia Academy in International Journal of Renewable Energy Development
- Vol. 12 (6) , 1091-1103
The effect of aeration rate and feedstock density on biodrying performance for wet refuse-derived fuel quality improvement
This study investigates the effect of aeration rate and feedstock density on the biodrying process to improve the quality of type 2 wet refuse-derived fuel. The aeration rate and feedstock density were varied to investigate these parameters’ effect on the system’s performance. The experiments used 0.3 m3 lysimeters with continuous negative ventilation and five days of operation. In Experiment A, aeration rates of 0.4, 0.5, and 0.6 m3/kg/day were tested with a feedstock bulk density of 232 kg/m3. In Experiment B, the optimum aeration rates determined in Experiment A (0.5 and 0.6 m3/kg/day) were used, and the feedstock density was varied (232 kg/m3, 250 kg/m3, and 270 kg/m3). The results showed that an aeration rate of 0.5 m3/kg/day was the most efficient for a feedstock density of 232 kg/m3; when the aeration rate was increased to 0.6 m3/kg/day, a feedstock density of 250 kg/m3 was the most effective. However, a feedstock density of 270 kg/m3 was not found to be practical for use in the quality improvement system. When the feedstock density is increased, the water in the feedstock and the water resulting from the biodegradation process cannot evaporate due to the feedstock layer’s low porosity, and the system requires an increased aeration rate. Furthermore, the increase in density scaled with increased initial volatile solid content, initial organic content, and initial moisture content, which significantly impacted the final moisture content based on multivariate regression analysis.
- 20 October 2023
- Published by Center of Biomass and Renewable Energy Scientia Academy in International Journal of Renewable Energy Development
- Vol. 12 (6) , 1091-1103
Open AccessThe effect of aeration rate and feedstock density on biodrying performance for wet refuse-derived fuel quality improvement
This study investigates the effect of aeration rate and feedstock density on the biodrying process to improve the quality of type 2 wet refuse-derived fuel. The aeration rate and feedstock density were varied to investigate these parameters’ effect on the system’s performance. The experiments used 0.3 m3 lysimeters with continuous negative ventilation and five days of operation. In Experiment A, aeration rates of 0.4, 0.5, and 0.6 m3/kg/day were tested with a feedstock bulk density of 232 kg/m3. In Experiment B, the optimum aeration rates determined in Experiment A (0.5 and 0.6 m3/kg/day) were used, and the feedstock density was varied (232 kg/m3, 250 kg/m3, and 270 kg/m3). The results showed that an aeration rate of 0.5 m3/kg/day was the most efficient for a feedstock density of 232 kg/m3; when the aeration rate was increased to 0.6 m3/kg/day, a feedstock density of 250 kg/m3 was the most effective. However, a feedstock density of 270 kg/m3 was not found to be practical for use in the quality improvement system. When the feedstock density is increased, the water in the feedstock and the water resulting from the biodegradation process cannot evaporate due to the feedstock layer’s low porosity, and the system requires an increased aeration rate. Furthermore, the increase in density scaled with increased initial volatile solid content, initial organic content, and initial moisture content, which significantly impacted the final moisture content based on multivariate regression analysis.
- Open Access
Modification of the Aeration-Supplied Configuration in the Biodrying Process for Refuse-Derived Fuel (RDF) Production
Biodrying is an essential part of the mechanical–biological treatment process that minimizes moisture content and simultaneously maximizes heating value for refuse-derived fuel (RDF) production. Although the mechanical separation process operates effectively in Thailand’s RDF production, high organic content levels and their degradation cause moisture contamination in RDF, producing wet RDF. Aeration is essential for an effective biodrying process, and can reduce RDF’s moisture content as well as increase its heating value. To maximize the biodrying effect, aeration should be optimized based on the waste conditions. This study proposes a modified aeration-supplied configuration for wet RDF biodrying. The aeration rate was modified based on the period within the biodrying operation; the first period is from the beginning until day 2.5, and the second period is from day 2.5 to day 5. The optimal aeration supply configuration was 0.5 m3/kg/day in the first period and then 0.3 m3/kg/day until the end of the process; this configuration yielded the greatest moisture content decrease of 35% and increased the low heating value of the biodried product by 11%. The final moisture content and low heating value were 24.07% and 4787 kcal/kg, respectively. Therefore, this optimal aeration-supplied configuration could be applied to meet the moisture content and low heating value requirements of the RDF production standard for Thailand’s local cement industry.
Open AccessModification of the Aeration-Supplied Configuration in the Biodrying Process for Refuse-Derived Fuel (RDF) Production
Biodrying is an essential part of the mechanical–biological treatment process that minimizes moisture content and simultaneously maximizes heating value for refuse-derived fuel (RDF) production. Although the mechanical separation process operates effectively in Thailand’s RDF production, high organic content levels and their degradation cause moisture contamination in RDF, producing wet RDF. Aeration is essential for an effective biodrying process, and can reduce RDF’s moisture content as well as increase its heating value. To maximize the biodrying effect, aeration should be optimized based on the waste conditions. This study proposes a modified aeration-supplied configuration for wet RDF biodrying. The aeration rate was modified based on the period within the biodrying operation; the first period is from the beginning until day 2.5, and the second period is from day 2.5 to day 5. The optimal aeration supply configuration was 0.5 m3/kg/day in the first period and then 0.3 m3/kg/day until the end of the process; this configuration yielded the greatest moisture content decrease of 35% and increased the low heating value of the biodried product by 11%. The final moisture content and low heating value were 24.07% and 4787 kcal/kg, respectively. Therefore, this optimal aeration-supplied configuration could be applied to meet the moisture content and low heating value requirements of the RDF production standard for Thailand’s local cement industry.
- Open Access
- 19 October 2022
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 41 (4) , 924-935
Investigation of plastic waste management in Thailand using material flow analysis
This study uses material flow analysis to investigate the amounts and pathways of municipal plastic waste (MPW) in Thailand. The aim is to understand the country’s situation and investigate the effects of Thailand’s Roadmap on Plastic Waste Management 2018 –2030, which sets a goal for recycling ‘target plastic waste’ at 100% by 2027. The analysis was conducted using waste statistics between 2008 and 2020 and waste forecasts. Two scenarios of plastic waste management, the business-as-usual, and the national roadmap, were constructed for 2025 and 2030. In 2030, the annual MPW generation is projected to reach 2.19 Mt. Under the business-as-usual (BAU) scenario, the recycling and utilisation rate will be 32.3% of waste generated. About 30.3% of waste generated will not be treated properly and possibly leaked into the open environment. Under the roadmap scenario, the recycling and utilisation rate will increase to 98.4%, while 1.6% of waste generated will not be treated properly. The recycling rate for target plastic waste in 2027 could only reach 67.1% because plastic waste is required as fuel for waste incinerators and industries. With the roadmap fully implemented, certain effects can be foreseen for waste-to-energy and plastic industries. Findings from this study stress on the importance of holistic policy planning, efficient prioritising and allocating of waste as a resource, and cooperation from all sectors for sustainable plastic waste management.
- 19 October 2022
- Published by SAGE Publications in Waste Management & Research: The Journal for a Sustainable Circular Economy
- Vol. 41 (4) , 924-935
Open AccessInvestigation of plastic waste management in Thailand using material flow analysis
This study uses material flow analysis to investigate the amounts and pathways of municipal plastic waste (MPW) in Thailand. The aim is to understand the country’s situation and investigate the effects of Thailand’s Roadmap on Plastic Waste Management 2018 –2030, which sets a goal for recycling ‘target plastic waste’ at 100% by 2027. The analysis was conducted using waste statistics between 2008 and 2020 and waste forecasts. Two scenarios of plastic waste management, the business-as-usual, and the national roadmap, were constructed for 2025 and 2030. In 2030, the annual MPW generation is projected to reach 2.19 Mt. Under the business-as-usual (BAU) scenario, the recycling and utilisation rate will be 32.3% of waste generated. About 30.3% of waste generated will not be treated properly and possibly leaked into the open environment. Under the roadmap scenario, the recycling and utilisation rate will increase to 98.4%, while 1.6% of waste generated will not be treated properly. The recycling rate for target plastic waste in 2027 could only reach 67.1% because plastic waste is required as fuel for waste incinerators and industries. With the roadmap fully implemented, certain effects can be foreseen for waste-to-energy and plastic industries. Findings from this study stress on the importance of holistic policy planning, efficient prioritising and allocating of waste as a resource, and cooperation from all sectors for sustainable plastic waste management.
- 13 July 2022
- Published by Springer Nature in Earth Systems and Environment
- Vol. 7 (1) , 83-97
Greenhouse Gas Mitigation and Energy Production Potentials from Municipal Solid Waste Management in Thailand Through 2050
- 13 July 2022
- Published by Springer Nature in Earth Systems and Environment
- Vol. 7 (1) , 83-97
Greenhouse Gas Mitigation and Energy Production Potentials from Municipal Solid Waste Management in Thailand Through 2050