Pravin P. Patil
Research Subjects
Pravin P. Patil has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Lakshmaiya Natrayan
Department of Mechanical Engineering, Saveetha School of Engineering, SIMATS, Chennai, India
3 shared publications - Seeniappan Kaliappan
Department of Mechanical Engineering, KCG College of Technology, Chennai, India
2 shared publications A. Muniappan
Department of Mechanical Engineering, Saveetha School of Engineering, SIMATS, Chennai, 602105 Tamil Nadu
1 shared publication- AP
Department of Mechanical Engineering Kumaraguru College of Technology Coimbatore Tamil Nadu India
1 shared publication Anil Kumar
Department of Botany DDU Gorakhpur University Gorakhpur Uttar Pradesh India
1 shared publicationB. Gnanasundara Jayaraja
Department of Mechanical Engineering St. Joseph College of Engineering Sriperumpudur Chennai India
1 shared publication
Latest Publications
- Open Access
- 28 April 2023
- Published by Hindawi Limited in Journal of Nanomaterials
- Vol. 2023, 1-8
Synthesized Nanoaluminum Oxide with Al2024 to Investigate Wear Behavior by Grey Relational Approach and ANN
Aluminum metal matrix composites (AMCs) have been employed in automobile manufacturing to reduce weight. Also this research concentrates on the tribological performances on the processed AMCs by the stir casting liquefying method. The aluminum alloy Al2024 was employed to nanoparticles of aluminum oxide for the preparation of AMCs with constant processing condition of stirring speed to produce the homogeneous dispersion. The processed composites were further investigated to identify the wear characteristics. Therefore, the dry sliding condition was achieved on the processed composites. The input parameters of dry sliding conditions are sliding distance, functional load, and sliding velocity, and the output characteristics are wear rate and coefficient of friction (COF). Those input parameters are framed by the Taguchi L9 array and parameters were further employed to optimize with grey relational analysis. From the L9 parameters, the better wear rate and COF were accumulated in the following parameter: 2,100mm of sliding distance, 25N of functional load, and 2.5m/s of sliding velocity, respectively. Then the wear rates and COF values are subjected to produce the predicted responses with supporting of artificial neural network. Most of the predicted values are much higher than the actual wear response vales. The wear resistance of all the samples composed better performances with dispersion of nanoaluminum oxide particles on the Al2024 alloy.
- 28 April 2023
- Published by Hindawi Limited in Journal of Nanomaterials
- Vol. 2023, 1-8
Open AccessSynthesized Nanoaluminum Oxide with Al2024 to Investigate Wear Behavior by Grey Relational Approach and ANN
Aluminum metal matrix composites (AMCs) have been employed in automobile manufacturing to reduce weight. Also this research concentrates on the tribological performances on the processed AMCs by the stir casting liquefying method. The aluminum alloy Al2024 was employed to nanoparticles of aluminum oxide for the preparation of AMCs with constant processing condition of stirring speed to produce the homogeneous dispersion. The processed composites were further investigated to identify the wear characteristics. Therefore, the dry sliding condition was achieved on the processed composites. The input parameters of dry sliding conditions are sliding distance, functional load, and sliding velocity, and the output characteristics are wear rate and coefficient of friction (COF). Those input parameters are framed by the Taguchi L9 array and parameters were further employed to optimize with grey relational analysis. From the L9 parameters, the better wear rate and COF were accumulated in the following parameter: 2,100mm of sliding distance, 25N of functional load, and 2.5m/s of sliding velocity, respectively. Then the wear rates and COF values are subjected to produce the predicted responses with supporting of artificial neural network. Most of the predicted values are much higher than the actual wear response vales. The wear resistance of all the samples composed better performances with dispersion of nanoaluminum oxide particles on the Al2024 alloy.
- 4 September 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (11) , 8388-8395
Mechanical, fracture toughness, and Dynamic Mechanical properties of twill weaved bamboo fiber‐reinforced Artocarpus heterophyllus seed husk biochar epoxy composite
This research aimed to find the effect of Artocarpus heterophyllus fruit seed husk biochar (ASB) and twill weaved bamboo fiber (TBF) in mechanical, DMA, and fracture toughness behavior of epoxy‐based composite. The surface of both weaved bamboo fiber and biochar was treated with amino silane before composite making. In this investigation, the laminates were fabricated by hand layup process and analyzed by appropriate ASTM standards. Results of this study revealed that the incorporation of 40 vol.% twill weaved bamboo fiber (EB) into the resin improved the mechanical properties. The load distribution was uniform with twilled weaving. For composite designation EBJ3, the maximum measured tensile strength was 168 MPa, the tensile modulus is 6.24 GPa, the flexural strength is 195 MPa, and the flexural modulus is 6.85 GPa, the izod impact is 6.24 J, and the hardness is 90 shore‐D. Similarly, the maximum storage modulus and lowest loss factor for the composite designation EBJ3 were measured to be 3.8 GPa and 0.4, respectively. Moreover, the maximum measured fracture toughness and energy release rate is 39.4 MPa.√m and 0.88 MJ/m2 for composite designation EBJ3 with 5.0% biochar and 40% bamboo fibers in volume. The SEM fractography revealed that the matrix molecules are adhered to the fiber, indicating enhanced bonding. These biomass waste converted fruit seed husk biochar and industrial crop bamboo fiber epoxy composites could be used as workable material in structural, defense, automotive, and domestic product‐making applications.
- 4 September 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (11) , 8388-8395
Mechanical, fracture toughness, and Dynamic Mechanical properties of twill weaved bamboo fiber‐reinforced Artocarpus heterophyllus seed husk biochar epoxy composite
This research aimed to find the effect of Artocarpus heterophyllus fruit seed husk biochar (ASB) and twill weaved bamboo fiber (TBF) in mechanical, DMA, and fracture toughness behavior of epoxy‐based composite. The surface of both weaved bamboo fiber and biochar was treated with amino silane before composite making. In this investigation, the laminates were fabricated by hand layup process and analyzed by appropriate ASTM standards. Results of this study revealed that the incorporation of 40 vol.% twill weaved bamboo fiber (EB) into the resin improved the mechanical properties. The load distribution was uniform with twilled weaving. For composite designation EBJ3, the maximum measured tensile strength was 168 MPa, the tensile modulus is 6.24 GPa, the flexural strength is 195 MPa, and the flexural modulus is 6.85 GPa, the izod impact is 6.24 J, and the hardness is 90 shore‐D. Similarly, the maximum storage modulus and lowest loss factor for the composite designation EBJ3 were measured to be 3.8 GPa and 0.4, respectively. Moreover, the maximum measured fracture toughness and energy release rate is 39.4 MPa.√m and 0.88 MJ/m2 for composite designation EBJ3 with 5.0% biochar and 40% bamboo fibers in volume. The SEM fractography revealed that the matrix molecules are adhered to the fiber, indicating enhanced bonding. These biomass waste converted fruit seed husk biochar and industrial crop bamboo fiber epoxy composites could be used as workable material in structural, defense, automotive, and domestic product‐making applications.
- 8 August 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (9) , 6571-6577
Preparation and characterization of opuntia‐cladode fiber and citron peel biochar toughened epoxy biocomposite
In this research, citron peel biochar and opuntia‐cladode fibers (OCF) reinforced epoxy composites were fabricated and characterized for mechanical, wear, and electrical properties. The biochar was prepared from the waste peels of citron edible fruit whereas the opuntia fiber was from the cladode of the opuntia plant. The laminates were fabricated by hand layup process and evaluated in accordance with the ASTM standards. The results revealed that the mechanical properties such as tensile strength, flexural strength, impact toughness, hardness and adhesion strength were increased by 36.2%, 30.6%, 91.3%, 1.1%, and 5.3% for composite designation EC containing 30 vol% of OCF. Similarly, the addition of citron biochar of 2 vol% increased the load bearing and dielectric properties. However, the inclusion of 30 vol% of OCF on composite designation EC the sp. wear rate recorded 0.018 mm 3 /Nm. Similarly, the lowest coefficient of friction and sp. wear rate is observed to be 0.42 and 0.008 mm 3 /Nm for the composite with 2.0 vol% biochar. The ECO 4 composite designation represented a maximum dielectric constant and dielectric loss of about 7.4 and 1.1, respectively. The SEM fractography demonstrates that the silane‐treatment strengthened the fiber‐matrix interface and improved the interlocking mechanism. Such mechanically robust, wear‐resistant improved and electrically conductive composites could be utilized in applications such as industrial sectors, spacecraft, automobile parts, packaging industries, and electrical appliances.
- 8 August 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (9) , 6571-6577
Preparation and characterization of opuntia‐cladode fiber and citron peel biochar toughened epoxy biocomposite
In this research, citron peel biochar and opuntia‐cladode fibers (OCF) reinforced epoxy composites were fabricated and characterized for mechanical, wear, and electrical properties. The biochar was prepared from the waste peels of citron edible fruit whereas the opuntia fiber was from the cladode of the opuntia plant. The laminates were fabricated by hand layup process and evaluated in accordance with the ASTM standards. The results revealed that the mechanical properties such as tensile strength, flexural strength, impact toughness, hardness and adhesion strength were increased by 36.2%, 30.6%, 91.3%, 1.1%, and 5.3% for composite designation EC containing 30 vol% of OCF. Similarly, the addition of citron biochar of 2 vol% increased the load bearing and dielectric properties. However, the inclusion of 30 vol% of OCF on composite designation EC the sp. wear rate recorded 0.018 mm 3 /Nm. Similarly, the lowest coefficient of friction and sp. wear rate is observed to be 0.42 and 0.008 mm 3 /Nm for the composite with 2.0 vol% biochar. The ECO 4 composite designation represented a maximum dielectric constant and dielectric loss of about 7.4 and 1.1, respectively. The SEM fractography demonstrates that the silane‐treatment strengthened the fiber‐matrix interface and improved the interlocking mechanism. Such mechanically robust, wear‐resistant improved and electrically conductive composites could be utilized in applications such as industrial sectors, spacecraft, automobile parts, packaging industries, and electrical appliances.
- 27 July 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (9) , 6300-6309
Fatigue, fracture toughness and DMA of biosilica toughened epoxy with stacked okra fiber and Al 2024‐T3 fiber metal laminate composite
In this present study, a natural fiber‐based fiber metal laminate (FML) was fabricated for various engineering applications. The primary aim of this present investigation was to study the effect of adding natural fiber along with metal and the effect of the surface‐treatment process on the reinforcements on load‐bearing and thermo‐mechanical properties. Okra fiber woven mat, aluminum 2024‐T3 foil and rice husk‐derived biosilica were used as reinforcements. For surface treatment, the metal foil was sandblasted whereas the okra fiber and biosilica were silane‐treated. The FML was fabricated using the vacuum bag method utilizing as‐received and silane‐treated reinforcements as two separate models. According to the results, the addition of Al foil and okra fiber improved the storage modulus and loss factor of about 4.2 GPa and 0.39 for surface‐treated reinforcements. Similarly, maximum fracture toughness and energy release of 39.42 MPa √m and 0.76 MJ/m2 for surface‐treated EOA2 composite designation. Moreover, the addition of okra fiber and Al foil increased the fatigue life counts up to 54,266, 48,116, and 26,263 for surface‐treated EOA2 composite at 30%, 60%, and 90% of ultimate tensile stress (UTS). Such thermo‐mechanical and load‐bearing properties improved FMLs could be used in automotive, aircraft, drone and other industrial applications requiring high structural rigidity and load absorbing capability.
- 27 July 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (9) , 6300-6309
Fatigue, fracture toughness and DMA of biosilica toughened epoxy with stacked okra fiber and Al 2024‐T3 fiber metal laminate composite
In this present study, a natural fiber‐based fiber metal laminate (FML) was fabricated for various engineering applications. The primary aim of this present investigation was to study the effect of adding natural fiber along with metal and the effect of the surface‐treatment process on the reinforcements on load‐bearing and thermo‐mechanical properties. Okra fiber woven mat, aluminum 2024‐T3 foil and rice husk‐derived biosilica were used as reinforcements. For surface treatment, the metal foil was sandblasted whereas the okra fiber and biosilica were silane‐treated. The FML was fabricated using the vacuum bag method utilizing as‐received and silane‐treated reinforcements as two separate models. According to the results, the addition of Al foil and okra fiber improved the storage modulus and loss factor of about 4.2 GPa and 0.39 for surface‐treated reinforcements. Similarly, maximum fracture toughness and energy release of 39.42 MPa √m and 0.76 MJ/m2 for surface‐treated EOA2 composite designation. Moreover, the addition of okra fiber and Al foil increased the fatigue life counts up to 54,266, 48,116, and 26,263 for surface‐treated EOA2 composite at 30%, 60%, and 90% of ultimate tensile stress (UTS). Such thermo‐mechanical and load‐bearing properties improved FMLs could be used in automotive, aircraft, drone and other industrial applications requiring high structural rigidity and load absorbing capability.
- 15 June 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (8) , 5159-5167
Effect of silanized stacked Kevlar fiber/brass 270 wire mesh on mechanical and impact toughness of cubic boron nitride–epoxy composite
Kevlar fiber and brass wire mesh reinforced with cubic boron nitride (CBN) particle‐toughened epoxy composites are investigated in this study. This study aims to determine the hybrid composite's mechanical and drop load impact behavior, as well as the effect of surface treatment on the lamina delamination resistance and load bearing phenomenon. The composite laminates were fabricated by hand layup process and characterized according to ASTM standards. The tensile, flexural, Izod impact, ILSS, and hardness testing results shows that adding 35 vol% reinforcements and 3.0 vol% CBN particles indicates the greatest research findings. However, when the stacking sequences B/K/K/B and K/B/B/K were modified from B/K/B/K, these values reduced. The EO2 composite shows improved results in mechanical and drop load impact behavior together with Kevlar fiber and brass wire mesh of alternating staking sequences with 3.0 vol% CBN particles. It is clear that B/K/B/K stacking sequence shows the highest mechanical properties and drop load impact behavior while, B/K/K/B shows lowest values. This hybrid composite with higher mechanical qualities and impact energy absorption might be used in defense armors, aerospace, structural, automobile, and household equipment manufacturing applications.
- 15 June 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (8) , 5159-5167
Effect of silanized stacked Kevlar fiber/brass 270 wire mesh on mechanical and impact toughness of cubic boron nitride–epoxy composite
Kevlar fiber and brass wire mesh reinforced with cubic boron nitride (CBN) particle‐toughened epoxy composites are investigated in this study. This study aims to determine the hybrid composite's mechanical and drop load impact behavior, as well as the effect of surface treatment on the lamina delamination resistance and load bearing phenomenon. The composite laminates were fabricated by hand layup process and characterized according to ASTM standards. The tensile, flexural, Izod impact, ILSS, and hardness testing results shows that adding 35 vol% reinforcements and 3.0 vol% CBN particles indicates the greatest research findings. However, when the stacking sequences B/K/K/B and K/B/B/K were modified from B/K/B/K, these values reduced. The EO2 composite shows improved results in mechanical and drop load impact behavior together with Kevlar fiber and brass wire mesh of alternating staking sequences with 3.0 vol% CBN particles. It is clear that B/K/B/K stacking sequence shows the highest mechanical properties and drop load impact behavior while, B/K/K/B shows lowest values. This hybrid composite with higher mechanical qualities and impact energy absorption might be used in defense armors, aerospace, structural, automobile, and household equipment manufacturing applications.
- 12 May 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (8) , 4899-4908
Characterization of prickly pear short fiber and red onion peel biocarbon nanosheets toughened epoxy composites
In this research, the role of prickly pear short fiber and red onion peel wrinkled biocarbon nanosheets toughened epoxy resin composite was investigated. The main aim of this research was to find the effectiveness of adding biocarbon along with prickly pear fiber in the load‐bearing, thermal and electrical conductivity behavior of the epoxy resin composite. The biocarbon nanosheets were prepared for this present investigation from red onion peel waste using the pyrolysis process. The composites were characterized by American society of testing and materials (ASTM) standards and compared with previous results. The highest tensile strength and flexural strength were observed for 3 vol.% of biocarbon nanosheets up to 60% and 40% respectively than pure epoxy. Izod impact toughness and hardness values also increased with the inclusion of reinforcements by 5 vol.% around 93% and 90% correspondingly. Similarly, relative permittivity and dielectric loss enhanced about to 6.4 and 0.74 for 5 vol.% of biocarbon nanosheets. The thermal conductivity also improved with the addition of biocarbon nanosheets and maximum values up to 0.42 W/mK. This enhanced dielectric, mechanical, and thermally active composites might be employed as a microwave shielding material in electronic devices, automotive, and industrial applications for communications equipment that require shielding material with good mechanical properties.
- 12 May 2022
- Published by Wiley in Polymer Composites
- Vol. 43 (8) , 4899-4908
Characterization of prickly pear short fiber and red onion peel biocarbon nanosheets toughened epoxy composites
In this research, the role of prickly pear short fiber and red onion peel wrinkled biocarbon nanosheets toughened epoxy resin composite was investigated. The main aim of this research was to find the effectiveness of adding biocarbon along with prickly pear fiber in the load‐bearing, thermal and electrical conductivity behavior of the epoxy resin composite. The biocarbon nanosheets were prepared for this present investigation from red onion peel waste using the pyrolysis process. The composites were characterized by American society of testing and materials (ASTM) standards and compared with previous results. The highest tensile strength and flexural strength were observed for 3 vol.% of biocarbon nanosheets up to 60% and 40% respectively than pure epoxy. Izod impact toughness and hardness values also increased with the inclusion of reinforcements by 5 vol.% around 93% and 90% correspondingly. Similarly, relative permittivity and dielectric loss enhanced about to 6.4 and 0.74 for 5 vol.% of biocarbon nanosheets. The thermal conductivity also improved with the addition of biocarbon nanosheets and maximum values up to 0.42 W/mK. This enhanced dielectric, mechanical, and thermally active composites might be employed as a microwave shielding material in electronic devices, automotive, and industrial applications for communications equipment that require shielding material with good mechanical properties.
- RetractedOpen Access
- 1 January 2022
- Published by SAGE Publications in Adsorption Science & Technology
- Vol. 2022
Experimental Investigation on the Effectiveness of Solar Still and Its Effect on Adsorption with Various Dyes
The typical solar still with internal and exterior heat transfer was used to test the impact of mixing various colours into the basin water. This is well-known that enhancing distillation involves adding black dye to basin water. Identical design parameters create two single-slope basin-type solar stills (effective area 0.5 m2). This study conducted experiments to add black, green, blue, and red dyes to basin water during the winter for 24 hours. For more than a month, the amount of distilled water recovered per hour, with varying temperatures and solar activity (May 2021). This research aims to (i) examine the effect of various dyes with basin water on the internal and external heat transfer and performance of the system and (ii) study the effect of adding dyes into the basin water on increasing energy balance by the solar system. This is indicated by the fact that the introduction of colours into the basin water has a major impact on external and interior heat transfer. The evaporation, radiation, and heat transfer rate from liquid to glass significantly impact how well the filtration system works.
- 1 January 2022
- Published by SAGE Publications in Adsorption Science & Technology
- Vol. 2022
RetractedOpen AccessExperimental Investigation on the Effectiveness of Solar Still and Its Effect on Adsorption with Various Dyes
The typical solar still with internal and exterior heat transfer was used to test the impact of mixing various colours into the basin water. This is well-known that enhancing distillation involves adding black dye to basin water. Identical design parameters create two single-slope basin-type solar stills (effective area 0.5 m2). This study conducted experiments to add black, green, blue, and red dyes to basin water during the winter for 24 hours. For more than a month, the amount of distilled water recovered per hour, with varying temperatures and solar activity (May 2021). This research aims to (i) examine the effect of various dyes with basin water on the internal and external heat transfer and performance of the system and (ii) study the effect of adding dyes into the basin water on increasing energy balance by the solar system. This is indicated by the fact that the introduction of colours into the basin water has a major impact on external and interior heat transfer. The evaporation, radiation, and heat transfer rate from liquid to glass significantly impact how well the filtration system works.