HCHasan Callioglu

Hasan Callioglu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hasan Callioglu has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Comparison of vibration values of rotating discs with variable parameters obtained by finite element analysis modeling with different machine learning algorithms

    by Hasan Callioglu, Said Muftu, Candaş Nuri Koplay

    Purpose: Rotating functionally graded (FG) disks of variable thickness generates vibration. This study aims to analyze the vibration generated by the rotating disks using a finite element program and compare the results obtained with the regression methods.Design/methodology/approach: Transverse vibration values of rotating FG disks with variable thickness were modeled using different regression methods. The accuracies of the obtained models are compared. In the context of comparing regression methods, multiple linear regression (MLR), extreme learning machine (ELM), artificial neural networks (ANNs) and radial basis function (RBF) were used in this study. The error graph between the observed value and the predicted value of each regression method was obtained. The error values of the regression methods used with scientific error measures were calculated.Findings: The analysis of the transverse vibration of rotating FG disks with the finite element program is consistent with the studies in the literature. When the variables and vibration value determined on the disk are modeled with ELM, MLR, ANN and RBF regression methods, it is concluded that the most accurate model order is RBF, ANN, MLR and ELM.Originality/value: There are studies on the vibration value of rotating discs in the literature, but there are very few studies on modeling. This study shows that ELM, MLR, ANN and RBF, which are machine learning methods, can be used in modeling the vibration value of rotating discs.


  • Open Access

    Large Deflection Analysis of Functionally Graded Beam by Using Combining Method

    by Ersin Demir, Hasan Çallıoğlu, Zekeriya Girgin

    In this study, the large deflection behavior of a circular cross-section beam is examined using the Combining Method (CM). The CM is a numerical solution method that uses block diagrams in the Matlab-Simulink program and weighting coefficients in the Differential Quadrature Method (DQM). The beam material considered is Functionally Graded Material (FGM). Boundary conditions of the beam are taken as clamped-free (C-F) and a singular load is assumed to be applied from the free end of the beam. Geometric nonlinear analysis is performed while calculating the large deflection equations of the beam and performing numerical analysis. The effects of increasing the force applied to the beam, changing the beam cross-section in the longitudinal direction, and changing the material index of the FGM on the extreme deflection behavior of the beam were examined. For comparison purposes, the results obtained from CM are compared with the results obtained from both SolidWorks-Simulation and Ansys-Workbench programs. As a result of the analysis, increasing the applied force causes the x and y coordinates of the end point of the beam to decrease. The change in geometry and material index greatly affects the large deflection occurring in the beam.


  • An approach for predicting longitudinal free vibration of axially functionally graded bar by artificial neural network

    by Ersin Demir, Metin Sayer, Hasan Callioglu

    In this study, an Artificial Neural Network (ANN) model is designed for the analysis of the longitudinal free vibration of an axially Functional Graded (FG) bar. The material of the bar is varied from one end to the other end according to power law function. Aluminum and Alumina and the mixture of these two materials are used in the analysis. The radius of the bar is also varied along to the longitudinal direction according to power law function. In addition, the effect of the variation in the slenderness ratio is also investigated. An ANN code is written in Matlab in order to obtain a generalized approach for vibration analysis of the FG bar. In the ANN training, some results of free vibration analysis obtained from the SolidWorks program based on Finite Element Method are used. The predicted values that are not used in the training are also obtained in SolidWorks for comparison. A Matlab program code, which based ANN method is used to find new values to be predicted. The process is also made for comparison with the ANN based Matlab nntool program. When the results obtained from SolidWorks and prepared Matlab code and Matlab nntool are compared, it is seen that the results are in harmony. AMS subject classifications: 74H45, 68T07


  • Impact behaviors of composite plates filled with chitosan/carbon nanotubes

    by Hasan Callioglu, Metin Sayer, Ersin Demir

    In this study, the effects of chitosan (1%, 2%, and 3%), multi-walled carbon nanotubes (0.1%, 0.2%, and 0.3%), and chitosan-carbon nanotube hybrid (1%, 2%, and 3% chitosan + 0.3% carbon nanotube) additions at different rates on the impact behaviors and the damage mechanisms of the E-glass/epoxy composite plates were investigated experimentally. The low-velocity drop impact testing was applied to the composite plates under different impact energies. The impact energy varied between 5 J and 30 J and it was possible to examine the impact response and the damage mechanism until the starting of the penetration of the composite plates. The experimental results revealed that the absorbed impact energies in chitosan and chitosan + carbon nanotube-filled composite plates were slightly higher than those in carbon nanotube-filled composite plates. The best energy absorption performances were obtained in chitosan + carbon nanotube hybrid filled composite plates when compared to all other composite plates and the neat composite plate. A certain amount of improvement in the impact strengths of the filled composite plates was observed when compared to neat composite plate. By increasing the impact energy, the fibers on the front surface were increasingly separated from the surface in an elliptical form, and the matrix cracking and the fiber breakages occurred throughout a line on the back surface.


  • Open Access

    Mechanical Behaviors of Composite Leaf Springs with Additive of Carbon Nanotubes and Chitosan

    by Hasan Çallıoğlu, Furkan Kavla

    Suspension systems are automotive parts which absorb sudden impacts caused by roads and providing comfort have an essential role in the automotive sector. Reducing weight is a fundamental way to decrease energy consumption and emission release. This study establishes improvement conditions by analysing layered composite springs which have different compositions and different support angles under various weights. Ten plaques which made with various compositions chitosan and carbon nanotubes, also one-way glass fiber/epoxy composite plaques with prepreg method and one unalloyed plaque were produced. Standard samples were extracted by water jet and pull&push test were applied to identify mechanical properties. Five standard samples were used to identify each mechanical property. Mechanical properties of samples with different compositions were compared. Identified mechanical properties were used as material properties at the ANSYS ACP PRE&POST analysis program. Composite spring thicknes were 12 mm and it is composed of 60 layers. Static analysis of composite springs modelled with five different layer orders was done by applying 1000 N, 2000 N, 3000 N and 3750 N force. Collapse, stress and shape changes of composite springs were examined at static analyses. Analysis show that unalloyed composite leaf spring is more resistant than its counterparts. When Layer Order 1 (TD1) [0°)] 60 with the same direction for fiber and horizontal axis of composite leaf spring is compared with others, it is seen that composite spring with TD1 is more rigid against bending. Damage analysis was done with ACP POST program according to Tsai-Wu and Hashin standards and it is seen that end points of springs were mostly damaged. Most damaged one is the TD5 leaf spring with [(0° 5 /90° 5 /45° 10 /-45° 10 )] s layer order under 3750 N according to Tsai-Wu standard. In addition to that, composite leaf springs were %49,84 lighter than mostly used one leaf steel counterparts.

  • Open Access

    Vibration analysis of sandwich beams with variable cross section on variable Winkler elastic foundation

    by Ersin Demir, Hasan Çallioğlu, Metin Sayer

    In this study, free vibration behavior of a multilayered symmetric sandwich beam made of functionally graded materials (FGMs) with variable cross section resting on variable Winkler elastic foundation are investigated. The elasticity and density of the functionally graded (FG) sandwich beam vary through the thickness according to the power law. This law is related to mixture rules and laminate theory. In order to provide this, a 50-layered beam is considered. Each layer is isotropic and homogeneous, although the volume fractions of the constituents of each layer are different. Furthermore, the width of the beam varies exponentially along the length of the beam, and also the beam is resting on an elastic foundation whose coefficient is variable along the length of the beam. The natural frequencies are computed for conventional boundary conditions of the FG sandwich beam using a theoretical procedure. The effects of material, geometric, elastic foundation indexes and slenderness ratio on natural frequencies and mode shapes of the beam are also computed and discussed. Finally, the results obtained are compared with a finite-element-based commercial program, ANSYS ® , and found to be consistent with each other.