MSMetin Sayer

Metin Sayer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Metin Sayer has a total of 7 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • An approach for predicting longitudinal free vibration of axially functionally graded bar by artificial neural network

    by Ersin Demir, Metin Sayer, Hasan Callioglu

    In this study, an Artificial Neural Network (ANN) model is designed for the analysis of the longitudinal free vibration of an axially Functional Graded (FG) bar. The material of the bar is varied from one end to the other end according to power law function. Aluminum and Alumina and the mixture of these two materials are used in the analysis. The radius of the bar is also varied along to the longitudinal direction according to power law function. In addition, the effect of the variation in the slenderness ratio is also investigated. An ANN code is written in Matlab in order to obtain a generalized approach for vibration analysis of the FG bar. In the ANN training, some results of free vibration analysis obtained from the SolidWorks program based on Finite Element Method are used. The predicted values that are not used in the training are also obtained in SolidWorks for comparison. A Matlab program code, which based ANN method is used to find new values to be predicted. The process is also made for comparison with the ANN based Matlab nntool program. When the results obtained from SolidWorks and prepared Matlab code and Matlab nntool are compared, it is seen that the results are in harmony. AMS subject classifications: 74H45, 68T07


  • An experimental study on the bearing strength of pin-loaded ceramic particles filled woven glass/epoxy composites

    by Metin Sayer

    The present study experimentally investigates the effect of various ceramic particles and different particle weight fractions on the bearing strength and failure modes of pinned joints in woven glass/epoxy composite plates. The composite plates are filled with Silicon Carbide (SiC), Aluminum Oxide (Al 2 O 3 ) and Boron Carbide (B 4 C) ceramic particles at 5%, 10% and 15% weight fractions. Tensile tests were carried out on single pinned joints in woven glass/epoxy composite specimens. Accordingly, the effects of ceramic particles, particle weight fractions and pin joint geometry were evaluated on the bearing strength and the failure modes. The damaged specimens were examined with load–pin displacement curves, visual and scanning electron microscope (SEM). The results showed that the bearing strength and failure mode were considerably affected by the ceramic particles, the particle weight fractions and the geometric dimensions. It was found that the addition of the ceramic particles into composites improved the bearing strengths of pinned joints in the composites for all weight fractions compared to the unfilled composite. The highest bearing strengths were obtained for composites filled with 10 wt.% particles. As a result, the increase in the bearing strength is almost 43% for composites filled with SiC, 53% filled with Al 2 O 3 and 47% filled with B 4 C compared to the unfilled composite, for ratio e/d = 3.


  • Impact behaviors of composite plates filled with chitosan/carbon nanotubes

    by Hasan Callioglu, Metin Sayer, Ersin Demir

    In this study, the effects of chitosan (1%, 2%, and 3%), multi-walled carbon nanotubes (0.1%, 0.2%, and 0.3%), and chitosan-carbon nanotube hybrid (1%, 2%, and 3% chitosan + 0.3% carbon nanotube) additions at different rates on the impact behaviors and the damage mechanisms of the E-glass/epoxy composite plates were investigated experimentally. The low-velocity drop impact testing was applied to the composite plates under different impact energies. The impact energy varied between 5 J and 30 J and it was possible to examine the impact response and the damage mechanism until the starting of the penetration of the composite plates. The experimental results revealed that the absorbed impact energies in chitosan and chitosan + carbon nanotube-filled composite plates were slightly higher than those in carbon nanotube-filled composite plates. The best energy absorption performances were obtained in chitosan + carbon nanotube hybrid filled composite plates when compared to all other composite plates and the neat composite plate. A certain amount of improvement in the impact strengths of the filled composite plates was observed when compared to neat composite plate. By increasing the impact energy, the fibers on the front surface were increasingly separated from the surface in an elliptical form, and the matrix cracking and the fiber breakages occurred throughout a line on the back surface.


  • Impact behavior of particles filled‐glass/polyester composite plates

    by Hasan Çallıoğlu, Metin Sayer, Ersin Demir

    The aim of the study is to lay bare the impact behavior of filled composite plates experimentally. The woven glass/polyester‐matrix composite plates filled with 0% (unfilled), 10%, and 20% SiCp ceramic particles were manufactured by hand lay‐up method. The low velocity drop impact testing is conducted to the composite samples subjected to increasing impact energies that were ranged from approximately 2.5 to 22.5 J. With this use of increasing impact energies, it was possible to examine the impact response and damage mechanism until perforation of the composite plates. An energy profiling method was used in order to identify the perforation thresholds of composites. It is concluded that addition of particles to resin, until a certain ratio, increases the perforation thresholds of the woven glass/polyester. The perforation threshold of 10% filled composite is about 37% higher than that of the 20% filled composite and 6% higher than ones of the unfilled composite. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers


  • Impact behavior of hybrid composite plates

    by Metin Sayer, Numan Behlül Bektaş, Hasan Çallioğlu

    This experimental study deals with the impact response of hybrid composite laminates. Two different hybrid composite laminates, aramid/glass and aramid/carbon, and two different stacking sequences, such as [0/0/90/90]A+ [90/90/0/0]G for AG1 and [0/90/±45]A+ [±45/90/0]G for AG2 and so on (see Table I), were chosen for impact testing. The impact energy was gradually increased until complete perforation took place, and an energy profiling method (EPM) was used to identify the perforation thresholds of composites. The damaged samples were visually inspected. The images of the several samples subjected to various impact energies were registered and used for comparison and identifying damage mechanisms. The perforation thresholds for [0/90/±45]s aramid/glass and aramid/carbon laminates were found to be approximately 5% higher than those for their counterparts with the [0/0/90/90]s stacking sequence. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010