YXYang Xu

Yang Xu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yang Xu has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Physics-Based Model for Snapback-Type ESD Protection Devices

    by Xin Yan, Seyed Mostafa Mousavi, Li Shen, Yang Xu, Wei Zhang, Sergej Bub, Steffen Holland, Daryl G. Beetner

    A simplified physical-based model for deep-snapback transient voltage suppressors (TVS) is developed in this article. While based on physics, the number of parameters and components is minimized, so the model can be tuned easily from available measurements of the packaged TVS. SPICE convergence issues seen in previous snapback device models are eliminated by adding nonlinear damping components to the model. No convergence issues were seen among any of the simulations performed for this study, which includes transmission-line pulse tests with multiple levels and rise times. The proposed model was used to represent two different TVS devices and was validated in both device- and system-level simulations. Simulations of quasi-static and transient behavior matched measurement results within about 20% among all the tested cases.


  • Improved SEED Modeling of an ESD Discharge to a USB Cable

    by Yang Xu, Jianchi Zhou, Sergej Bub, Steffen Holland, Javad Soleiman Meiguni, David Pommerenke, Daryl G. Beetner

    Integrated circuits (ICs) connected to a universal serial bus (USB) interface require robust electrostatic discharge (ESD) protection strategies due to the nature of the high-speed interface and the regular access by users. System-efficient ESD design (SEED) simulations can help predict the level of ESD stress seen by the IC when protected by a transient voltage suppressor (TVS). In the following paper, previously developed models were improved to predict the voltage and current seen by a TVS and an on-chip protection diode when an ESD gun was discharged to one USB cable pin. Models were improved, in part, by accurately modeling the conductivity modulation within the behavioral TVS model and by using a measured equivalent source to represent the complex interaction between the ESD gun, USB cable, and enclosure. The response of the TVS and on-chip diode was studied in simulation and measurement for several cable configurations and when adding passive components between the TVS and on-chip diode. Simulations predicted peak and quasi-static voltages and currents at the TVS and on-chip diode within 30% of those seen in measurements. The proposed modeling process can help engineers to evaluate and optimize the effectiveness of their ESD protection strategies under complicated test conditions.


  • Characterization and Modeling of Commercial ICs for System-Efficient ESD Design

    by Zhekun Peng, Yang Xu, Manje Yea, Sergej Bub, Steffen Holland, DongHyun Kim, David Pommerenke, Daryl G. Beetner

    Optimizing electrostatic discharge (ESD) protection strategies requires simulation models of both on - and off -die ESD devices, but detailed information about on -die ESD protection is rarely available. Methods are proposed in the following paper to characterize and model the on -chip ESD protection using only measurements, with minimal a priori information about how the protection is implemented. The characterization targets a three-terminal (rather than the traditional two-terminal) protection structure, including the I/O, Vdd, Vss pins, and allows for current to flow between multiple pins simultaneously. A previously-developed behavioral model for TVS devices is used to capture the ESD behavior of the integrated circuit (IC), including its linear, quasi-static, and transient nonlinear response. The approach is used to model the equivalent current that flows through the on -chip ESD protection of two commercial ICs. The model of the on -chip ESD protection is combined with a behavioral model of an off -chip transient voltage suppressor to demonstrate their combined performance in a system-efficient ESD design (SEED) simulation. The model is validated both when the IC is powered- off and powered- on . The SEED model was able to predict quasistatic and peak voltages and currents at the IC with less than a 10% error.


  • Transient Response of ESD Protection Devices for a High-Speed I/O Interface

    by Jianchi Zhou, Yang Xu, Sergej Bub, Steffen Holland, Javad Soleiman Meiguni, David Pommerenke, Daryl G. Beetner

    System-efficient electrostatic discharge (ESD) design (SEED) models of a diode and transient voltage suppressor (TVS) were developed to study their transient response in a high-speed input/output interface. Previously reported SEED models were improved to strengthen their convergence stability and facilitate accurate predictions over a wide range of conditions. These improvements were required to accurately capture the race conditions between the TVS and on -chip diode, where the diode's turn on may prevent turn on of the TVS. Simulations and measurements were performed to demonstrate the impact of the ESD pulse's rise time on race conditions. During a race, results showed the worst-case quasi-static diode current could be twice as high for long rise-time pulses than for short rise-times where the TVS does not turn on , and on -chip diode current may be larger at low test voltages than at high test voltages where the TVS does turn on . Adding a small passive impedance between the external TVS and the on -chip diode helps the TVS turn on and reduce the current through the on -chip diode by more than 50%. Similarly, lengthening the trace between the TVS and diode could reduce on -chip diode current by up to a factor of two.


  • Open Access

    Modeling Strategy for EMI Filters

    by Ruijie He, Yang Xu, Sameer Walunj, Shaohui Yong, Victor Khilkevich, David Pommerenke, Hermann L. Aichele, Martin Boettcher, Philipp Hillenbrand, Andreas Klaedtke

    Performance of electromagnetic interference (EMI) filters in power-electronics applications is limited by the parasitic coupling between the components of the filters and the self-parasitic of each component. While these parasitic effects can be partially taken into account on the circuit level, it is difficult to estimate their values. In this article, a full-wave modeling methodology is proposed to predict the performance of a complete EMI filter up to 1 GHz. Following the proposed methodology, the mutual couplings among the EMI filter components are taken into account as well as the self-parasitics of each individual component. Experiments and simulations are carried out to validate the modeling methodology. A self-parasitic cancellation technique is also applied to demonstrate the benefits of three-dimensional modeling methodology in EMI filter design.