D. P. Shvetsov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
D. P. Shvetsov has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- N. I. Sinitsin
Ural Federal University named after the first President of Russia B.N. Yeltsin
1 shared publication - Olga Anatolievna Chikova
Ural Federal University named after the first President of Russia B.N. Yeltsin
1 shared publication Precision Casting Center Llc
1 shared publication- V. V. V’yUkhin
Ural Federal University named after the first President of Russia B.N. Yeltsin
1 shared publication - Vladimir S. Tsepelev
Ural Federal University named after the first President of Russia B.N. Yeltsin
1 shared publication
Latest Publications
- Open Access
- 8 November 2025
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 68 (5) , 534-542
Physico-chemical analysis of 12Kh18N9TL steel melts for quality control of cast products
The authors studied the behavior of slag inclusions in four samples taken during casting of austenitic corrosion-resistant steel grade 12Kh18N9TL. The samples for the study were taken under production conditions after melting the charge ( 1 ), introducing Ti and FeMn, slag induction and additional loading ( 2 ), re-introducing Ti, slag induction ( 3 ), slag induction ( 4 ). The elemental composition and temperature of the melt were determined under production conditions. The physicochemical properties of the melts obtained from the selected samples were measured under laboratory conditions: surface tension and kinematic viscosity. The measurements were carried out in the temperature range from 1370 to 1760 °C in the mode of heating and subsequent cooling of the sample. When observing the sample during the measurement of surface tension, the release of slag inclusions from the volume of the drop occurs in the heating mode. During subsequent cooling of the formed drop of liquid steel, slag particles flow from the slag bath under the action of the Marangoni force. Analysis of the dependence of the slag particle ascent rate on its size showed that only particles up to 10 μm in size can remain in the melt volume, while larger particles have time to float to the surface of the liquid bath. It was found that slag particles up to 4 mm in size can flow onto the surface of the sample under the action of the Marangoni force. The volume fraction of slag inclusions was determined, and a correlation was established between it and the element composition of the sample. The authors made a conclusion about the effect of Ti additives in the melt as the cause of increase in the volume fraction of slag inclusions in the casting.
- 8 November 2025
- Published by National University of Science and Technology MISiS in Izvestiya. Ferrous Metallurgy
- Vol. 68 (5) , 534-542
Open AccessPhysico-chemical analysis of 12Kh18N9TL steel melts for quality control of cast products
The authors studied the behavior of slag inclusions in four samples taken during casting of austenitic corrosion-resistant steel grade 12Kh18N9TL. The samples for the study were taken under production conditions after melting the charge ( 1 ), introducing Ti and FeMn, slag induction and additional loading ( 2 ), re-introducing Ti, slag induction ( 3 ), slag induction ( 4 ). The elemental composition and temperature of the melt were determined under production conditions. The physicochemical properties of the melts obtained from the selected samples were measured under laboratory conditions: surface tension and kinematic viscosity. The measurements were carried out in the temperature range from 1370 to 1760 °C in the mode of heating and subsequent cooling of the sample. When observing the sample during the measurement of surface tension, the release of slag inclusions from the volume of the drop occurs in the heating mode. During subsequent cooling of the formed drop of liquid steel, slag particles flow from the slag bath under the action of the Marangoni force. Analysis of the dependence of the slag particle ascent rate on its size showed that only particles up to 10 μm in size can remain in the melt volume, while larger particles have time to float to the surface of the liquid bath. It was found that slag particles up to 4 mm in size can flow onto the surface of the sample under the action of the Marangoni force. The volume fraction of slag inclusions was determined, and a correlation was established between it and the element composition of the sample. The authors made a conclusion about the effect of Ti additives in the melt as the cause of increase in the volume fraction of slag inclusions in the casting.
- 1 January 2022
- Published by Russian State Vocational Pedagogical University in Insight
- Vol. 2 (10)
SOFT COMPETENCIES OF A WORKER: A MENTOR'S VIEW
The article reveals the need to define soft competencies of workers in modern production. The article presents a list of necessary soft-competencies and analyzes their key importance in the processes of modernization and introduction of innovations in the enterprise on the basis of mentor’s experience
- 1 January 2022
- Published by Russian State Vocational Pedagogical University in Insight
- Vol. 2 (10)
SOFT COMPETENCIES OF A WORKER: A MENTOR'S VIEW
The article reveals the need to define soft competencies of workers in modern production. The article presents a list of necessary soft-competencies and analyzes their key importance in the processes of modernization and introduction of innovations in the enterprise on the basis of mentor’s experience