Francoise Bezerra
Research Subjects
Research Interests
Francoise Bezerra has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Marine Ruffenach
Centre National dEtudes Spatiales (CNES), Toulouse, France
5 shared publications - Hugo Cintas
Institute of Experimental and Applied Physics, Czech Technical University in Prague, 110 00 Prague, Czech Republic
4 shared publications - Julien Mekki
Centre National dEtudes Spatiales (CNES), Toulouse, France
4 shared publications - Sophie Duzellier
French Aerospace Laboratory (ONERA), Toulouse, France
3 shared publications - Athina Varotsou
TRAD Tests and Radiations, Labge, France
2 shared publications - Frederic Wrobel
Institut d’Électronique et des Systèmes (IES), UMR-CNRS 5214, University of Montpellier, Montpellier, France
2 shared publications
Latest Publications
- Open Access
- 1 March 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (03) , C03011
Evaluation of Timepix2 in adaptive gain mode for stopped and penetrating position-sensitive ion spectroscopy
We present the study of the response of a Timepix2 detector (256 × 256 pixels, pixel pitch 55 µm) with a 500 µm thick silicon sensor in laboratory measurements with α sources, charged particle beams of relativistic ion fragments at the Super-Proton-Synchrotron at CERN and in short-ranged heavy ion beams at the Heavy Ion Facility of UCLouvain in Belgium: 22Ne, 53Cr and 103Rh of 238, 505 and 957 MeV, respectively. The Timepix2 detector was used in adaptive gain mode, and calibrated using previously developed methodology using protons with energies in the range from 500 keV to 2 MeV and α-particles of 5.5 MeV from 241Am source prior to the testing. In a laboratory experiment, the detector was irradiated with α-particle from a 239Pu241Am244Cm source. α-particles of higher energy (∼ 9 MeV) were obtained through a measurement of naturally occurring decays of radon and its daughters while the detector was left running in the laboratory for two weeks. In both cases, an energy resolution of 2% was achieved. In the stopped ion beam measurement, the proper ion energy determination was hindered by the per-pixel saturation of 3.2 MeV. Still, due to an increase of measured energy with increasing charge deposition, the different ion species were separable. In the last study, the dE/dX spectra were obtained in a mixed relativistic particle beam and used to evaluate the capability of determining the beam composition. The spectrum stripping technique using iterative Landau curve fitting was applied to the spectra allowing for ion charge determination up to Z = 13. The per-pixel saturation was mitigated by placing the detector at an angle of 70 degrees with respect to the sensor normal.
- 1 March 2025
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 20 (03) , C03011
Open AccessEvaluation of Timepix2 in adaptive gain mode for stopped and penetrating position-sensitive ion spectroscopy
We present the study of the response of a Timepix2 detector (256 × 256 pixels, pixel pitch 55 µm) with a 500 µm thick silicon sensor in laboratory measurements with α sources, charged particle beams of relativistic ion fragments at the Super-Proton-Synchrotron at CERN and in short-ranged heavy ion beams at the Heavy Ion Facility of UCLouvain in Belgium: 22Ne, 53Cr and 103Rh of 238, 505 and 957 MeV, respectively. The Timepix2 detector was used in adaptive gain mode, and calibrated using previously developed methodology using protons with energies in the range from 500 keV to 2 MeV and α-particles of 5.5 MeV from 241Am source prior to the testing. In a laboratory experiment, the detector was irradiated with α-particle from a 239Pu241Am244Cm source. α-particles of higher energy (∼ 9 MeV) were obtained through a measurement of naturally occurring decays of radon and its daughters while the detector was left running in the laboratory for two weeks. In both cases, an energy resolution of 2% was achieved. In the stopped ion beam measurement, the proper ion energy determination was hindered by the per-pixel saturation of 3.2 MeV. Still, due to an increase of measured energy with increasing charge deposition, the different ion species were separable. In the last study, the dE/dX spectra were obtained in a mixed relativistic particle beam and used to evaluate the capability of determining the beam composition. The spectrum stripping technique using iterative Landau curve fitting was applied to the spectra allowing for ion charge determination up to Z = 13. The per-pixel saturation was mitigated by placing the detector at an angle of 70 degrees with respect to the sensor normal.
- 19 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1638-1644
Proton, Electron, and Photon Flux Measurement and Simulation During Stratospheric Balloon Flights
This paper compares three models of the atmospheric radiative environment: MAIRE (Model of Atmospheric Ionizing Radiative Effects), EXPACS (Excel-based Program for calculating Atmospheric Cosmic-ray Spectrum) and RAMSEES (Radiation Atmospheric Model for Single Event Effect Simulation) to experimental fluxes measured at different altitudes. The PIX CNES (Centre National d’Etudes Spatiales) instrument recorded the fluxes during five stratospheric flights. There is no standard way to model the atmospheric radiative environment today. Each model uses its own Monte Carlo toolkit, modeling the atmosphere and primary particles. The Radiations Atmospheric Model for SEE Simulation (RAMSEES) was created by Geant4 simulation of the Extensive Air Shower (EAS) phenomenon generated by highly energetic Galactic Cosmic Rays (GCR) in 100 km of atmosphere. By using PIX fluxes, this paper aims to benchmark the models with experimental data at multiple altitudes. Three integral fluxes were used in this paper at a comparison point: photons >0.823 MeV, electrons >10.27 MeV, and protons >80 MeV. MAIRE shows good agreement with all the experimental fluxes from 5 to 40 km. MAIRE predictions show remarkable agreement with the PIX photon fluxes. EXPACS predictions are in a magnitude order of PIX measurements but tend to underestimate the fluxes. Finally, RAMSEES predictions agree with PIX fluxes for protons, electrons, and photons at altitudes of 5 to 32.5 km. Moreover, RAMSEES shows a significant agreement with PIX proton fluxes.
- 19 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1638-1644
Proton, Electron, and Photon Flux Measurement and Simulation During Stratospheric Balloon Flights
This paper compares three models of the atmospheric radiative environment: MAIRE (Model of Atmospheric Ionizing Radiative Effects), EXPACS (Excel-based Program for calculating Atmospheric Cosmic-ray Spectrum) and RAMSEES (Radiation Atmospheric Model for Single Event Effect Simulation) to experimental fluxes measured at different altitudes. The PIX CNES (Centre National d’Etudes Spatiales) instrument recorded the fluxes during five stratospheric flights. There is no standard way to model the atmospheric radiative environment today. Each model uses its own Monte Carlo toolkit, modeling the atmosphere and primary particles. The Radiations Atmospheric Model for SEE Simulation (RAMSEES) was created by Geant4 simulation of the Extensive Air Shower (EAS) phenomenon generated by highly energetic Galactic Cosmic Rays (GCR) in 100 km of atmosphere. By using PIX fluxes, this paper aims to benchmark the models with experimental data at multiple altitudes. Three integral fluxes were used in this paper at a comparison point: photons >0.823 MeV, electrons >10.27 MeV, and protons >80 MeV. MAIRE shows good agreement with all the experimental fluxes from 5 to 40 km. MAIRE predictions show remarkable agreement with the PIX photon fluxes. EXPACS predictions are in a magnitude order of PIX measurements but tend to underestimate the fluxes. Finally, RAMSEES predictions agree with PIX fluxes for protons, electrons, and photons at altitudes of 5 to 32.5 km. Moreover, RAMSEES shows a significant agreement with PIX proton fluxes.
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1631-1637
Benchmarking Trapped Proton Specification Models Along an EOR Orbit
Eutelsat 7C (E7C), a telecommunication spacecraft, was launched on 21 st of June 2019 and reached geostationary (GEO) orbit four months later after a quasi-equatorial electric orbit raising (EOR) phase. An ICARE-NG (Influence sur les Composant Avancés des Radiations de l’Espace, Nouvelle Génération) radiation monitor was implemented on the spacecraft allowing measurements of electron and proton flux as well as Single Event Upset (SEU) effect affecting various static random access memories (SRAMs) and dynamic random access memories (DRAMs). According to the cruise to GEO profile, two phases could be deduced, a first one where SEU events are dominated by trapped protons and a second one where they are attributed to cosmic rays and solar proton events. In this paper, SEU events attributed to trapped particles as well as proton flux recorded by ICARE-NG are used to benchmark proton specification models, Aerospace Proton version 8 (AP8), Aerospace Proton version 9 (AP9) and Global Radiation Earth ENvironment-proton (GREEN-p). Although, the 3D shielding of the spacecraft and payload is considered to transport accurately the proton environment down to the chip, ground tests to define cross section were not reliable enough to draw clear conclusion on specification model performances along EOR orbits.
- 10 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1631-1637
Benchmarking Trapped Proton Specification Models Along an EOR Orbit
Eutelsat 7C (E7C), a telecommunication spacecraft, was launched on 21 st of June 2019 and reached geostationary (GEO) orbit four months later after a quasi-equatorial electric orbit raising (EOR) phase. An ICARE-NG (Influence sur les Composant Avancés des Radiations de l’Espace, Nouvelle Génération) radiation monitor was implemented on the spacecraft allowing measurements of electron and proton flux as well as Single Event Upset (SEU) effect affecting various static random access memories (SRAMs) and dynamic random access memories (DRAMs). According to the cruise to GEO profile, two phases could be deduced, a first one where SEU events are dominated by trapped protons and a second one where they are attributed to cosmic rays and solar proton events. In this paper, SEU events attributed to trapped particles as well as proton flux recorded by ICARE-NG are used to benchmark proton specification models, Aerospace Proton version 8 (AP8), Aerospace Proton version 9 (AP9) and Global Radiation Earth ENvironment-proton (GREEN-p). Although, the 3D shielding of the spacecraft and payload is considered to transport accurately the proton environment down to the chip, ground tests to define cross section were not reliable enough to draw clear conclusion on specification model performances along EOR orbits.
- 22 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1527-1534
PIX: An Instrument to Measure Atmospheric Ionizing Particles Based on a Single MiniPIX Sensor
This paper presents the PIX instrument based on a raspberry Pi and a MiniPIX device dedicated to make measurements of ionizing particles onboard stratospheric balloons. The hardware part and the software part of the PIX instrument are described. All the characteristics of the instrument are given in this paper. The three flight opportunities are also presented, with the associated measurements. The methodology to calculate fluxes based on measurements is explained. In particular, the calculation of response functions of protons, electrons, and photons by using Monte-Carlo simulations, the identification algorithm based on a neural network trained with simulated data, and the calculation of fluxes from count rates are described. Some measurements performed in different facilities are presented. A part of these experimental tracks have been used to challenge the neural network previously trained with simulated date, to check the robustness of the algorithm. Proton, electron, and photon fluxes are presented and compared to the MAIRE model.
- 22 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 71 (8) , 1527-1534
PIX: An Instrument to Measure Atmospheric Ionizing Particles Based on a Single MiniPIX Sensor
This paper presents the PIX instrument based on a raspberry Pi and a MiniPIX device dedicated to make measurements of ionizing particles onboard stratospheric balloons. The hardware part and the software part of the PIX instrument are described. All the characteristics of the instrument are given in this paper. The three flight opportunities are also presented, with the associated measurements. The methodology to calculate fluxes based on measurements is explained. In particular, the calculation of response functions of protons, electrons, and photons by using Monte-Carlo simulations, the identification algorithm based on a neural network trained with simulated data, and the calculation of fluxes from count rates are described. Some measurements performed in different facilities are presented. A part of these experimental tracks have been used to challenge the neural network previously trained with simulated date, to check the robustness of the algorithm. Proton, electron, and photon fluxes are presented and compared to the MAIRE model.
- Open Access
RAMSEES: A Model of the Atmospheric Radiative Environment Based on Geant4 Simulation of Extensive Air Shower
The device downscaling of electronic components has given rise to the need to consider specific failures in onboard airplane electronics. Single Event Effects (SEE) are a kind of failures that occur due to radiation in the atmosphere. For the purpose of ensuring onboard electronic reliability, there is a clear need for new tools to predict the SEE rate, at both avionic altitudes and at ground level. In this work, we develop a new tool: RAMSEES (Radiation Atmospheric Model for SEE Simulation), which simulates the atmospheric radiative environment induced by cosmic rays. This multiscale and multi-physics phenomenon is simulated using the Geant4 toolkit, allowing the creation of a database to characterize the radiation environment in the atmosphere as a function of altitude. We show the need to simulate very high-energy particles such as 100 TeV space protons, because they are the main contributor of radiation at avionic altitudes as well as at ground level. Our approach shows a good agreement with the experimental data, the standards, and other models, and it also points out some discrepancies, especially below 18 km of altitude. RAMSEES can be the basis of the estimation of the SEE rate from ground level to the stratosphere, at any given position and time.
Open AccessRAMSEES: A Model of the Atmospheric Radiative Environment Based on Geant4 Simulation of Extensive Air Shower
The device downscaling of electronic components has given rise to the need to consider specific failures in onboard airplane electronics. Single Event Effects (SEE) are a kind of failures that occur due to radiation in the atmosphere. For the purpose of ensuring onboard electronic reliability, there is a clear need for new tools to predict the SEE rate, at both avionic altitudes and at ground level. In this work, we develop a new tool: RAMSEES (Radiation Atmospheric Model for SEE Simulation), which simulates the atmospheric radiative environment induced by cosmic rays. This multiscale and multi-physics phenomenon is simulated using the Geant4 toolkit, allowing the creation of a database to characterize the radiation environment in the atmosphere as a function of altitude. We show the need to simulate very high-energy particles such as 100 TeV space protons, because they are the main contributor of radiation at avionic altitudes as well as at ground level. Our approach shows a good agreement with the experimental data, the standards, and other models, and it also points out some discrepancies, especially below 18 km of altitude. RAMSEES can be the basis of the estimation of the SEE rate from ground level to the stratosphere, at any given position and time.
- 20 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (8) , 1533-1540
14 Years of In-Flight Experimental Data on CARMEN-MEX
This paper presents in-flight Single Event Effects (SEE), Total Ionizing Dose (TID) and Total Non-Ionizing Dose (TNID) data collected since 2008 by CNES with CARMEN-MEX experiment on board of various satellites placed in Low-Earth Orbit or Geostationary orbits.
- 20 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (8) , 1533-1540
14 Years of In-Flight Experimental Data on CARMEN-MEX
This paper presents in-flight Single Event Effects (SEE), Total Ionizing Dose (TID) and Total Non-Ionizing Dose (TNID) data collected since 2008 by CNES with CARMEN-MEX experiment on board of various satellites placed in Low-Earth Orbit or Geostationary orbits.
- 21 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (8) , 1607-1612
Role of Electron-Induced Coulomb Interactions to the Total SEU Rate During Earth and JUICE Missions
The contribution of Coulomb processes induced by incident electrons in SEU sensitivity is investigated. The case of a 65-nm SOI memory is studied. Several orbits (GPS, JUICE’s orbits) are analyzed. The relative importance to the total SEU rate of electron, proton and gamma environments is compared. SEU induced by electrons are obtained during Earth missions. In the environment of Jupiter, equivalent SEU sensitivities have been obtained between the studied device and the ESA SEU monitor. However, the relative importance of the physical processes involved is very different. Proton-induced SEU rates are estimated about one decade greater than electron-induced SEU rates. The Bremsstrahlung contribution has found negligible in such environment.
- 21 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (8) , 1607-1612
Role of Electron-Induced Coulomb Interactions to the Total SEU Rate During Earth and JUICE Missions
The contribution of Coulomb processes induced by incident electrons in SEU sensitivity is investigated. The case of a 65-nm SOI memory is studied. Several orbits (GPS, JUICE’s orbits) are analyzed. The relative importance to the total SEU rate of electron, proton and gamma environments is compared. SEU induced by electrons are obtained during Earth missions. In the environment of Jupiter, equivalent SEU sensitivities have been obtained between the studied device and the ESA SEU monitor. However, the relative importance of the physical processes involved is very different. Proton-induced SEU rates are estimated about one decade greater than electron-induced SEU rates. The Bremsstrahlung contribution has found negligible in such environment.
- 18 November 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 58 (6) , 2644-2651
In Flight SEU/MCU Sensitivity of Commercial Nanometric SRAMs: Operational Estimations
A method and the corresponding platform devoted to operational SEE-rate prediction are presented and illustrated by experimental results. Predicted error-rates are in well agreement with results issued from the activation of an SRAM platform, in 90 nm technology node, on board stratospheric balloons flights. Direct ionization of protons is investigated for a 65 SRAM memory virtually boarded on the balloon flight.
- 18 November 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 58 (6) , 2644-2651
In Flight SEU/MCU Sensitivity of Commercial Nanometric SRAMs: Operational Estimations
A method and the corresponding platform devoted to operational SEE-rate prediction are presented and illustrated by experimental results. Predicted error-rates are in well agreement with results issued from the activation of an SRAM platform, in 90 nm technology node, on board stratospheric balloons flights. Direct ionization of protons is investigated for a 65 SRAM memory virtually boarded on the balloon flight.
- 9 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 57 (00189499) , 3127-3134
Impact of the Solar Flares on the SER Dynamics on Micro and Nanometric Technologies
The objective of this paper is to study the impact of the solar flares on the single event rate (SER) dynamics investigating the influence of shielding, the technological integration level and the contribution of the direct ionization of protons for a 65 nm technology. This paper proposes a comparison of MUSCA SEP3 calculations and SAC-C satellite in-flight data in terms of SEU “instantaneous” rate and total count.
- 9 November 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 57 (00189499) , 3127-3134
Impact of the Solar Flares on the SER Dynamics on Micro and Nanometric Technologies
The objective of this paper is to study the impact of the solar flares on the single event rate (SER) dynamics investigating the influence of shielding, the technological integration level and the contribution of the direct ionization of protons for a 65 nm technology. This paper proposes a comparison of MUSCA SEP3 calculations and SAC-C satellite in-flight data in terms of SEU “instantaneous” rate and total count.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 03796566,p. 1-7
Probing SET sensitive volumes in linear devices using focused laser beam at different wavelengths
The main objective of the work presented here is to explore the ability of laser irradiations to determine the SET sensitive depths of a linear device by using several wavelengths. Laser testing at two wavelengths allows the estimation of sensitive depths. The approach conducted here is applied for the first time to a linear device with very deep sensitive depth. The 1064 nm wavelength seems to be the most adequate one to reveal all sensitive areas and, when comparing with heavy ion experimental data, shows a reasonable agreement with heavy ion cross section.
- 1 September 2007
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 03796566,p. 1-7
Probing SET sensitive volumes in linear devices using focused laser beam at different wavelengths
The main objective of the work presented here is to explore the ability of laser irradiations to determine the SET sensitive depths of a linear device by using several wavelengths. Laser testing at two wavelengths allows the estimation of sensitive depths. The approach conducted here is applied for the first time to a linear device with very deep sensitive depth. The 1064 nm wavelength seems to be the most adequate one to reveal all sensitive areas and, when comparing with heavy ion experimental data, shows a reasonable agreement with heavy ion cross section.