Arkadiusz Czarnuch
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Arkadiusz Czarnuch has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Damian Batory
Department of Vehicles and Fundamentals of Machine Design, Lodz University of Technology, 1/15 Stefanowskiego St., 90-924 Lodz, Poland
4 shared publications - Marek Stembalski
Department of Machine Tools and Mechanical Technologies, Wroclaw University of Science and Technology, 50-370 Wrocław, Poland
4 shared publications - Tomasz Szydłowski
Department of Vehicles and Fundamentals of Machine Design, Lodz University of Technology, 90-924 Łódź, Poland
4 shared publications Damian Batory
1 shared publication- Daniel Nycz
Institute of Technology, Jan Grodek State Vocational Academy, Sanok, Poland
1 shared publication Maciej Kaczor
1 shared publication
Latest Publications
- Open Access
- 22 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 14 (1) , 127
Assessment of the Possibility of Validating the Durability Testing Method for Large-Sized Vehicles Based on Changes in Shock Absorber Characteristics—Preliminary Tests
The use of road simulators in vehicle durability tests enables a significant reduction in time related to the implementation of a new product. However, there is still a need to improve the methods of these tests in order to obtain a full correlation between the time of the tests on the simulator with respect to the mileage of the vehicle in real road conditions. The aim of this work is a validation and improvement of the durability testing method for large-sized vehicles. Comparative tests of shock absorbers dismantled from semi-trailers with different mileage and shock absorbers dismantled from semi-trailers after durability tests conducted at the MTS test bench are presented. The relationship between the maximum damping force and the displacement speed of the shock absorber piston was examined. Additionally, the influence of the shock absorber temperature on the damping force was analyzed. As a result of the tests, the dynamic characteristics of the shock absorbers were determined and the relationship between the maximum damping force and the mileage of the trailers was determined. It was found that the load on the trailers during their operation has a significant impact on the change in the characteristics of the shock absorbers. What is new in this publication is the validation of the methodology for conducting durability tests previously proposed by the authors based on the selected component, which is the shock absorber. The authors have not yet encountered in the literature any attempt to validate the methodology for conducting durability tests for large-sized vehicles.
- 22 December 2023
- Published by MDPI AG in Applied Sciences
- Vol. 14 (1) , 127
Open AccessAssessment of the Possibility of Validating the Durability Testing Method for Large-Sized Vehicles Based on Changes in Shock Absorber Characteristics—Preliminary Tests
The use of road simulators in vehicle durability tests enables a significant reduction in time related to the implementation of a new product. However, there is still a need to improve the methods of these tests in order to obtain a full correlation between the time of the tests on the simulator with respect to the mileage of the vehicle in real road conditions. The aim of this work is a validation and improvement of the durability testing method for large-sized vehicles. Comparative tests of shock absorbers dismantled from semi-trailers with different mileage and shock absorbers dismantled from semi-trailers after durability tests conducted at the MTS test bench are presented. The relationship between the maximum damping force and the displacement speed of the shock absorber piston was examined. Additionally, the influence of the shock absorber temperature on the damping force was analyzed. As a result of the tests, the dynamic characteristics of the shock absorbers were determined and the relationship between the maximum damping force and the mileage of the trailers was determined. It was found that the load on the trailers during their operation has a significant impact on the change in the characteristics of the shock absorbers. What is new in this publication is the validation of the methodology for conducting durability tests previously proposed by the authors based on the selected component, which is the shock absorber. The authors have not yet encountered in the literature any attempt to validate the methodology for conducting durability tests for large-sized vehicles.
- Open Access
Analysis of the Correctness of Mapping the Passage of a Semi-Trailer through a Road Obstacle on a Road Simulator
Road simulators enable accelerated durability tests under similar-to-real road conditions. However, the road simulator itself generates the signals with the appropriate strength and amplitude that is adequate to the response registered by the sensors during the real run. Therefore, there is a need for verification of the validity of the representation of vehicle runs on a road simulator in terms of the shape of the generated profile and possible sources of uncertainty. The tests in this study were carried out for a multi-axle vehicle passing an obstacle of known shape. Various signals were registered while the vehicle was passing over the obstacle. The MTS (System Corporation) road simulator’s response to the signal given by the obstacle was then checked. The results showed a 99% correlation between the simulation and the road test results. A numerical model of the vehicle was developed to verify the quality of representation of the real conditions by the road simulator, especially in terms of forces resulting from the road profile. Interestingly, the input signal generated by the road simulator provided a very good accuracy of the vehicle response, as tested with use of the numerical model.
Open AccessAnalysis of the Correctness of Mapping the Passage of a Semi-Trailer through a Road Obstacle on a Road Simulator
Road simulators enable accelerated durability tests under similar-to-real road conditions. However, the road simulator itself generates the signals with the appropriate strength and amplitude that is adequate to the response registered by the sensors during the real run. Therefore, there is a need for verification of the validity of the representation of vehicle runs on a road simulator in terms of the shape of the generated profile and possible sources of uncertainty. The tests in this study were carried out for a multi-axle vehicle passing an obstacle of known shape. Various signals were registered while the vehicle was passing over the obstacle. The MTS (System Corporation) road simulator’s response to the signal given by the obstacle was then checked. The results showed a 99% correlation between the simulation and the road test results. A numerical model of the vehicle was developed to verify the quality of representation of the real conditions by the road simulator, especially in terms of forces resulting from the road profile. Interestingly, the input signal generated by the road simulator provided a very good accuracy of the vehicle response, as tested with use of the numerical model.
- 22 February 2023
- Published by Springer Nature
- p. 236-246
Methodology of the Durability Tests of Semi-trailers on the MTS 320 Road Simulator
- 22 February 2023
- Published by Springer Nature
- p. 236-246
Methodology of the Durability Tests of Semi-trailers on the MTS 320 Road Simulator
- 30 September 2021
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 23 (3) , 548-558
Method of reconstructing dynamic load characteristics for durability test Indexed by: of heavy semitrailer under different road conditions
The aim of the article is to present and validate a methodology for collecting road load data on a vehicle, driving on roads and analysis of a drive data signal under the wheel in the time domain, using FRF (Frequency Response Function) and the MTS 320 eight-poster inertia reacted road simulator. The elaborated drive data, was used to control the actuators forcing the movements of the wheels and the coupling part of the semi-trailer during durability tests. The road tests were carried out by registering physical variables in the time domain, by a set of sensors mounted on a vehicle. The data was collected from roads categorized as motorways, national and local roads. Differences between the variability of the parameters, collected on the roads and the variability of the drive data under the wheel, were determined for the particular types of roads, for loaded and unloaded vehicle. The obtained accuracy of reconstruction of the road load data conditions was as high as 97%. Therefore, the proposed method is suitable for reliable durability tests with use of the road simulator.
- 30 September 2021
- Published by Polskie Naukowo-Techniczne Towarzystwo Eksploatacyjne in Eksploatacja i Niezawodność – Maintenance and Reliability
- Vol. 23 (3) , 548-558
Method of reconstructing dynamic load characteristics for durability test Indexed by: of heavy semitrailer under different road conditions
The aim of the article is to present and validate a methodology for collecting road load data on a vehicle, driving on roads and analysis of a drive data signal under the wheel in the time domain, using FRF (Frequency Response Function) and the MTS 320 eight-poster inertia reacted road simulator. The elaborated drive data, was used to control the actuators forcing the movements of the wheels and the coupling part of the semi-trailer during durability tests. The road tests were carried out by registering physical variables in the time domain, by a set of sensors mounted on a vehicle. The data was collected from roads categorized as motorways, national and local roads. Differences between the variability of the parameters, collected on the roads and the variability of the drive data under the wheel, were determined for the particular types of roads, for loaded and unloaded vehicle. The obtained accuracy of reconstruction of the road load data conditions was as high as 97%. Therefore, the proposed method is suitable for reliable durability tests with use of the road simulator.
- Open Access
- 6 February 2017
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- Vol. 90 (2) , 140-143
Design, manufacture and experimental verification of side safety device for Wielton trucks
Presented is a new design-technological solution of a side safety device for Wielton trucks. A side safety device is manufactured of glass-polyester laminates and foam using press technology. Numerical modelling in MSC.Marc system and experimental verification tests were conducted according to Regulations no. 73. A good qualitative and quantitative compatibility of the results, were obtained.
- 6 February 2017
- Published by SIMP Redakcja Mechanik - Agenda Wydawnicza SIMP in Mechanik
- Vol. 90 (2) , 140-143
Open AccessDesign, manufacture and experimental verification of side safety device for Wielton trucks
Presented is a new design-technological solution of a side safety device for Wielton trucks. A side safety device is manufactured of glass-polyester laminates and foam using press technology. Numerical modelling in MSC.Marc system and experimental verification tests were conducted according to Regulations no. 73. A good qualitative and quantitative compatibility of the results, were obtained.