İbRahim Pazarkaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
İbRahim Pazarkaya has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Mehmet Yazar
Çanakkale Onsekiz Mart Üniversitesi
6 shared publications - Ahmet Özdemir
Gazi Üniversitesi
3 shared publications - Mithat Yanıkören
Bilecik Şeyh Edebali Üniversitesi
2 shared publications - Musa Kaya
Atatürk Mesleki ve Teknik Anadolu Lisesi Müdürlüğü
2 shared publications - Nihat Döngel
Gazi Üniversitesi
2 shared publications - Ramazan Bülbül
Gazi Üniversitesi
2 shared publications
Latest Publications
- 28 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Tribological performance and wear prediction of spur gears lubricated with palm oil and lithium grease: A hybrid physics-informed machine learning approach
Gear wear prediction and sustainable lubrication are critical for Industry 4.0 predictive maintenance. In this study, spur gear wear under lubrication with palm oil and a lithium complex grease was evaluated using a Taguchi L32 design and ANOVA. Results showed palm oil outperformed grease, yielding lower mass losses (6–17 mg vs. 9–18 mg), with minimum loss (6–8 mg) at 192 rpm. Vibration analysis revealed lower Root Mean Square (RMS) values for palm oil at 480 rpm (0.0017–0.0081 mm) than grease (0.0033–0.0119 mm), while grease reached Peak-to-Peak amplitudes up to 0.034 mm. Taguchi S/N ratio analysis identified optimal conditions (palm oil, 192 rpm, 40 min) with palm oil achieving a higher mean S/N ratio (39.7 vs. 37.5). ANOVA indicated significant contributions from duration (20.96%, p = 0.037) and lubricant type (16.76%, p = 0.009). In contrast, 50.54% unexplained error highlighted complex interactions. To address data constraints, 32 physical samples were augmented using the Archard equation, yielding a total of 192 samples. A CatBoost model trained via 5-fold GroupKFold cross-validation achieved high accuracy in the LOW wear regime (mean R 2 logK = 0.7198, linear R 2 K = 0.6994, MSE logK = 0.0092, linear RMSE K = 6.9 × 10 −9 ). Conversely, the HIGH wear regime exhibited non-linear instability (mean R 2 logK = −2.7017, linear R 2 K = −11.7590). Feature importance confirmed regime-dependent behavior: revolutions (∼28%) and duration (∼22%) dominated in the LOW regime, whereas sliding distance (∼90%) dominated in the HIGH regime. Overall, this hybrid physics-informed ML approach robustly predicts gear wear under stable operating conditions while identifying critical wear-transition boundaries.
- 28 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
Tribological performance and wear prediction of spur gears lubricated with palm oil and lithium grease: A hybrid physics-informed machine learning approach
Gear wear prediction and sustainable lubrication are critical for Industry 4.0 predictive maintenance. In this study, spur gear wear under lubrication with palm oil and a lithium complex grease was evaluated using a Taguchi L32 design and ANOVA. Results showed palm oil outperformed grease, yielding lower mass losses (6–17 mg vs. 9–18 mg), with minimum loss (6–8 mg) at 192 rpm. Vibration analysis revealed lower Root Mean Square (RMS) values for palm oil at 480 rpm (0.0017–0.0081 mm) than grease (0.0033–0.0119 mm), while grease reached Peak-to-Peak amplitudes up to 0.034 mm. Taguchi S/N ratio analysis identified optimal conditions (palm oil, 192 rpm, 40 min) with palm oil achieving a higher mean S/N ratio (39.7 vs. 37.5). ANOVA indicated significant contributions from duration (20.96%, p = 0.037) and lubricant type (16.76%, p = 0.009). In contrast, 50.54% unexplained error highlighted complex interactions. To address data constraints, 32 physical samples were augmented using the Archard equation, yielding a total of 192 samples. A CatBoost model trained via 5-fold GroupKFold cross-validation achieved high accuracy in the LOW wear regime (mean R 2 logK = 0.7198, linear R 2 K = 0.6994, MSE logK = 0.0092, linear RMSE K = 6.9 × 10 −9 ). Conversely, the HIGH wear regime exhibited non-linear instability (mean R 2 logK = −2.7017, linear R 2 K = −11.7590). Feature importance confirmed regime-dependent behavior: revolutions (∼28%) and duration (∼22%) dominated in the LOW regime, whereas sliding distance (∼90%) dominated in the HIGH regime. Overall, this hybrid physics-informed ML approach robustly predicts gear wear under stable operating conditions while identifying critical wear-transition boundaries.
- 1 March 2026
- Published by Igdir University in Journal of the Institute of Science and Technology
- Vol. 16 (1) , 270-282
Design, Modal Analysis, Additive Manufacturing, and Flow Performance of An Elliptical Gear Hydraulic Pump
In this study, the design, manufacturing, modal analysis and flow performance of hydraulic pumps with elliptical and spur gear profiles are compared experimentally. Firstly, both gear types are modeled in a computer-aided design (CAD) environment and their natural frequencies and mode shapes are analyzed using the finite element method (FEM). As a result of modal analyses performed on four different thermoplastic materials, ABS, PC, PETG and PLA, PLA material is preferred due to its high frequency resistance and production suitability. In line with the selected geometry and material, gear pairs were produced by additive manufacturing (3D printing) method and prototype pumps are assembled. Both pump systems are tested at rotational speeds ranging from 1000 to 3000 rpm to measure volumetric flow performance. Experimental results showed that, at all speeds, the elliptical gear pump delivered a higher and more stable flow rate compared to the spur gear pump. At the highest test speed of 3000 rpm, the elliptical gear pump achieved an average flow rate of 23.6 L/min, whereas the spur gear pump produced only 4.9 L/min. Similarly, at the lowest test speed of 1500 rpm, the elliptical gear pump generated 8.29 L/min, while the spur gear pump delivered 2.05 L/min. These findings indicate that the elliptical gear geometry can improve pump performance by approximately fourfold, offering a compact and highly efficient alternative for hydraulic systems.
- 1 March 2026
- Published by Igdir University in Journal of the Institute of Science and Technology
- Vol. 16 (1) , 270-282
Design, Modal Analysis, Additive Manufacturing, and Flow Performance of An Elliptical Gear Hydraulic Pump
In this study, the design, manufacturing, modal analysis and flow performance of hydraulic pumps with elliptical and spur gear profiles are compared experimentally. Firstly, both gear types are modeled in a computer-aided design (CAD) environment and their natural frequencies and mode shapes are analyzed using the finite element method (FEM). As a result of modal analyses performed on four different thermoplastic materials, ABS, PC, PETG and PLA, PLA material is preferred due to its high frequency resistance and production suitability. In line with the selected geometry and material, gear pairs were produced by additive manufacturing (3D printing) method and prototype pumps are assembled. Both pump systems are tested at rotational speeds ranging from 1000 to 3000 rpm to measure volumetric flow performance. Experimental results showed that, at all speeds, the elliptical gear pump delivered a higher and more stable flow rate compared to the spur gear pump. At the highest test speed of 3000 rpm, the elliptical gear pump achieved an average flow rate of 23.6 L/min, whereas the spur gear pump produced only 4.9 L/min. Similarly, at the lowest test speed of 1500 rpm, the elliptical gear pump generated 8.29 L/min, while the spur gear pump delivered 2.05 L/min. These findings indicate that the elliptical gear geometry can improve pump performance by approximately fourfold, offering a compact and highly efficient alternative for hydraulic systems.
- 23 February 2026
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 14 (1) , 447-458
C45E malzemenin Tornalama İşleminde Oluşan Kesme Kuvvetlerinin Makine Öğrenmesi Modelleriyle Tahmini: DNN ve XGBoost Modellerinin Performans Karşılaştırması
Günümüzde bilgisayar ve yazılım alanındaki gelişmelerle birlikte yapay zeka ve makine öğrenmesi alanında önemli gelişmeler olduğu bilinmektedir. Bu çalışmada, Vladimir Mitrović ve arkadaşlarının oluşturduğu, silindirik tornalama işlemi sırasında oluşan kesme kuvvetlerini barındıran veri seti kullanılarak derin öğrenme (DNN) ve XGBoost makine öğrenmesi modellerinin kesme kuvveti tahmin yetenekleri karşılaştırılmıştır. Teğetsel kesme kuvveti (Ft) ele alındığında DNN ve XGBoost modelin sırasıyla %99,71 ve %99,89 R2 değeriyle birbirlerine oldukça yakın tahmin yetenekleri olduğu görülmüştür. Benzer şekilde eksenel kuvvet (Fa) tahminlerinde ise DNN modelin R2 = %98,65, XGBoost modelin R2 = %99,60 oranında tahmin yeteneğine sahip olduğu tespit edilmiştir. Radyal kuvvet (Fr) incelendiğinde XGBoost modelin, DNN modele göre %5,94 oranında daha iyi tahmin yapabildiği sonucuna varılmıştır. Genel olarak XGBoost modelin, DNN modele göre daha performanslı olduğu belirlenmiştir. Ayrıca XGBoost modelde iterasyon sayısı olmadığından DNN modele göre hızlı hesap yapabildiği görülmüştür.
- 23 February 2026
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 14 (1) , 447-458
C45E malzemenin Tornalama İşleminde Oluşan Kesme Kuvvetlerinin Makine Öğrenmesi Modelleriyle Tahmini: DNN ve XGBoost Modellerinin Performans Karşılaştırması
Günümüzde bilgisayar ve yazılım alanındaki gelişmelerle birlikte yapay zeka ve makine öğrenmesi alanında önemli gelişmeler olduğu bilinmektedir. Bu çalışmada, Vladimir Mitrović ve arkadaşlarının oluşturduğu, silindirik tornalama işlemi sırasında oluşan kesme kuvvetlerini barındıran veri seti kullanılarak derin öğrenme (DNN) ve XGBoost makine öğrenmesi modellerinin kesme kuvveti tahmin yetenekleri karşılaştırılmıştır. Teğetsel kesme kuvveti (Ft) ele alındığında DNN ve XGBoost modelin sırasıyla %99,71 ve %99,89 R2 değeriyle birbirlerine oldukça yakın tahmin yetenekleri olduğu görülmüştür. Benzer şekilde eksenel kuvvet (Fa) tahminlerinde ise DNN modelin R2 = %98,65, XGBoost modelin R2 = %99,60 oranında tahmin yeteneğine sahip olduğu tespit edilmiştir. Radyal kuvvet (Fr) incelendiğinde XGBoost modelin, DNN modele göre %5,94 oranında daha iyi tahmin yapabildiği sonucuna varılmıştır. Genel olarak XGBoost modelin, DNN modele göre daha performanslı olduğu belirlenmiştir. Ayrıca XGBoost modelde iterasyon sayısı olmadığından DNN modele göre hızlı hesap yapabildiği görülmüştür.
- Open Access
- 9 February 2026
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
- Vol. 69 (217)
Investigation of the Effect of Perforations Applied to the İnner Layers of Cross-Laminated Timber (CLT) Panels on Thermal Insulation Performance by Experimental and Finite Element Methods
In this study, perforations at rates of 10% and 20% were applied to the inner layers of cross-laminated timber (CLT) panels, manufactured from fir and oak wood, with thicknesses of 51 mm for three-layer panels and 85 mm for five-layer panels, in order to improve their thermal insulation properties. The thermal conductivity and thermal transmittance coefficients of both groups of CLT panels with perforations were determined using both experimental methods and the Finite Element Method (FEM). According to the results obtained from the experiments, the perforation process applied to the inner layers of the CLT panels was found to cause reductions in both the thermal conductivity and thermal transmittance coefficients. The greatest decrease in the thermal conductivity coefficient was observed in the panels with 20% perforation, showing a reduction of 10.8%, while the thermal transmittance coefficient decreased by 8.7% in the same panels. Furthermore, it was observed that the results obtained from the Finite Element Method (FEM) analyses showed similarity to those obtained through experimental methods. In conclusion, the study demonstrated that the use of different wood species and varying perforation rates in the production of CLT panels have a positive and statistically significant effect on the thermal insulation properties of these panels. Therefore, applying various perforation techniques can be recommended to improve the thermal insulation performance of CLT panels.
- 9 February 2026
- Published by Lukasiewicz Research Network - Poznan Technology Institute in Drewno. Prace Naukowe, Doniesienia, Komunikaty = Wood. Research Papers, Reports, Announcements
- Vol. 69 (217)
Open AccessInvestigation of the Effect of Perforations Applied to the İnner Layers of Cross-Laminated Timber (CLT) Panels on Thermal Insulation Performance by Experimental and Finite Element Methods
In this study, perforations at rates of 10% and 20% were applied to the inner layers of cross-laminated timber (CLT) panels, manufactured from fir and oak wood, with thicknesses of 51 mm for three-layer panels and 85 mm for five-layer panels, in order to improve their thermal insulation properties. The thermal conductivity and thermal transmittance coefficients of both groups of CLT panels with perforations were determined using both experimental methods and the Finite Element Method (FEM). According to the results obtained from the experiments, the perforation process applied to the inner layers of the CLT panels was found to cause reductions in both the thermal conductivity and thermal transmittance coefficients. The greatest decrease in the thermal conductivity coefficient was observed in the panels with 20% perforation, showing a reduction of 10.8%, while the thermal transmittance coefficient decreased by 8.7% in the same panels. Furthermore, it was observed that the results obtained from the Finite Element Method (FEM) analyses showed similarity to those obtained through experimental methods. In conclusion, the study demonstrated that the use of different wood species and varying perforation rates in the production of CLT panels have a positive and statistically significant effect on the thermal insulation properties of these panels. Therefore, applying various perforation techniques can be recommended to improve the thermal insulation performance of CLT panels.
- Open Access
- 28 December 2025
- Published by International Journal of 3D Printing Technologies and Digital Industry in International Journal of 3D Printing Technologies and Digital Industry
- Vol. 9 (3) , 515-526
THE EFFECT OF THICKNESS AND FILAMENT TYPE ON THE MODAL BEHAVIOR OF 3D PRINTED SPUR GEARS
Nowadays, the modal analysis method is effectively employed in the design of low-noise, high-safety machines, the production of comfortable vehicles, and the development of structures resistant to dynamic loads, the establishment of safe operating conditions, and the determination of optimal operating parameters. In this study, modal analyses were conducted on spur gear models produced using four commonly utilized 3D printing filament materials (PLA, ABS, PET-G, and PC) each in four different thicknesses)3 mm, 5 mm, 7 mm, and 9 mm). The analyses were performed using a finite element analysis (FEA)-based simulation software. For each combination of material type and gear thickness, natural frequencies (Hz) and corresponding eigenvalues (1/s²) were obtained across six distinct vibration modes. The results indicate that both frequency and eigenvalue values vary significantly depending on the material type and gear thickness. It was observed that the thickness parameter has a substantial impact on the natural frequency in the lower modes. This comprehensive study graphically compares the vibrational behavior of different materials and thicknesses and provides a scientific basis for identifying the most suitable material–geometry combinations in terms of modal performance.
- 28 December 2025
- Published by International Journal of 3D Printing Technologies and Digital Industry in International Journal of 3D Printing Technologies and Digital Industry
- Vol. 9 (3) , 515-526
Open AccessTHE EFFECT OF THICKNESS AND FILAMENT TYPE ON THE MODAL BEHAVIOR OF 3D PRINTED SPUR GEARS
Nowadays, the modal analysis method is effectively employed in the design of low-noise, high-safety machines, the production of comfortable vehicles, and the development of structures resistant to dynamic loads, the establishment of safe operating conditions, and the determination of optimal operating parameters. In this study, modal analyses were conducted on spur gear models produced using four commonly utilized 3D printing filament materials (PLA, ABS, PET-G, and PC) each in four different thicknesses)3 mm, 5 mm, 7 mm, and 9 mm). The analyses were performed using a finite element analysis (FEA)-based simulation software. For each combination of material type and gear thickness, natural frequencies (Hz) and corresponding eigenvalues (1/s²) were obtained across six distinct vibration modes. The results indicate that both frequency and eigenvalue values vary significantly depending on the material type and gear thickness. It was observed that the thickness parameter has a substantial impact on the natural frequency in the lower modes. This comprehensive study graphically compares the vibrational behavior of different materials and thicknesses and provides a scientific basis for identifying the most suitable material–geometry combinations in terms of modal performance.
- 16 December 2025
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- No. Advanced O
Lepleme İşlemi Üzerine Bilimsel Yayınların Bibliyometrik Analizi
Hassas ölçü ve geometrik tamlığın önem kazandığı günümüzde çeşitli imalat yöntemleri uygulanmaktadır. Bu imalat yöntemlerinden birisi de “lepleme” işlemidir. Bu çalışmada, Web of Science (WOS) veri tabanında taranan lepleme işlemiyle ilgili makaleleri araştırılmış ve 602 adet çalışmaya erişilmiştir. Makaleler, 15.08.2025 tarihinde “lapping” kelimesi aratılarak ve sadece makine mühendisliğini ilgilendiren alanlar dahil edilerek bibliyometrik analiz yapılmıştır. En fazla makalenin 2023 yılında 43 adet ve en fazla çalışma yayımlanan alanın ise 258 adetle imalat mühendisliği alanında yapıldığı görülmüştür. En etkin makale 952 atıfla Bıfano, TG “Ductile-Regime Grinding - A New Technology For Machining Brittle Materials” isimli çalışmasıdır. Ancak Bıfano, TG sadece 1 makale yayınlamıştır. En fazla makale üreten yazar 14 makale ve 129 atıfla Kang Renke’dir. Lepleme işlemiyle ilgili 83 adetle en fazla çalışma yayımlayan dergi “International Journal of Advanced Manufacturing Technology”, 1352 atıfla en fazla atıf alan dergiyse “International Journal of Machine Tools Manufacture” dergisidir. En fazla tercih edilen anahtar kelimeyse “lepleme (lapping)” ve yüzey pürüzlülüğü (surface roughness) kelimeleridir. En fazla çalışmayı üreten ülke 228 makale, 2795 atıfla Çin Halk Cumhuriyetidir. Türkiye ise sadece 3 makale üretmiştir. En fazla çalışmayı gerçekleştiren kurum 15 makale, 354 atıfla Harbin Teknoloji Enstitüsü’dür. Türkiye’de leplemeyle ilgili Ankara Üniversitesi, Çanakkale Onsekiz Mart Üniversitesi, Gazi Üniversitesi, Gaziantep Üniversitesi ve Hacettepe Üniversitesi çalışma yapmıştır.
- 16 December 2025
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- No. Advanced O
Lepleme İşlemi Üzerine Bilimsel Yayınların Bibliyometrik Analizi
Hassas ölçü ve geometrik tamlığın önem kazandığı günümüzde çeşitli imalat yöntemleri uygulanmaktadır. Bu imalat yöntemlerinden birisi de “lepleme” işlemidir. Bu çalışmada, Web of Science (WOS) veri tabanında taranan lepleme işlemiyle ilgili makaleleri araştırılmış ve 602 adet çalışmaya erişilmiştir. Makaleler, 15.08.2025 tarihinde “lapping” kelimesi aratılarak ve sadece makine mühendisliğini ilgilendiren alanlar dahil edilerek bibliyometrik analiz yapılmıştır. En fazla makalenin 2023 yılında 43 adet ve en fazla çalışma yayımlanan alanın ise 258 adetle imalat mühendisliği alanında yapıldığı görülmüştür. En etkin makale 952 atıfla Bıfano, TG “Ductile-Regime Grinding - A New Technology For Machining Brittle Materials” isimli çalışmasıdır. Ancak Bıfano, TG sadece 1 makale yayınlamıştır. En fazla makale üreten yazar 14 makale ve 129 atıfla Kang Renke’dir. Lepleme işlemiyle ilgili 83 adetle en fazla çalışma yayımlayan dergi “International Journal of Advanced Manufacturing Technology”, 1352 atıfla en fazla atıf alan dergiyse “International Journal of Machine Tools Manufacture” dergisidir. En fazla tercih edilen anahtar kelimeyse “lepleme (lapping)” ve yüzey pürüzlülüğü (surface roughness) kelimeleridir. En fazla çalışmayı üreten ülke 228 makale, 2795 atıfla Çin Halk Cumhuriyetidir. Türkiye ise sadece 3 makale üretmiştir. En fazla çalışmayı gerçekleştiren kurum 15 makale, 354 atıfla Harbin Teknoloji Enstitüsü’dür. Türkiye’de leplemeyle ilgili Ankara Üniversitesi, Çanakkale Onsekiz Mart Üniversitesi, Gazi Üniversitesi, Gaziantep Üniversitesi ve Hacettepe Üniversitesi çalışma yapmıştır.
- Open Access
- 6 November 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (11) , 488
Improving the Surface Finish of Spur Gears Using Palm Oil-Based Lapping: Comparison with Other Industrial Lapping Solutions
Palm oil is among the most produced plant oils in the world and is solid at room temperature. This study aims to produce a palm oil-based lapping solution that contributes to sustainable manufacturing. A palm oil-based lapping solution was compared with grease and industrial lapping solutions. Lapping processes were conducted on cylindrical spur gear wheels following the Taguchi L27 experimental design, utilizing three distinct RPMs and varying times. The average surface roughness value after the lapping procedure diminished by 39.45% with the palm oil lapping solution, demonstrating greater effectiveness than the other treatments. The most significant percentage change among all lapping solutions was −59.06%, achieved with palm oil at 32 rpm for 10 min. On the other hand, the Taguchi L27 signal-to-noise analysis shows that the palm oil lapping solution yielded the optimal outcome at 50 rpm and 16 min. A palm oil-based lapping solution was seen as capable of replacing mineral oil-based lapping solutions.
- 6 November 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (11) , 488
Open AccessImproving the Surface Finish of Spur Gears Using Palm Oil-Based Lapping: Comparison with Other Industrial Lapping Solutions
Palm oil is among the most produced plant oils in the world and is solid at room temperature. This study aims to produce a palm oil-based lapping solution that contributes to sustainable manufacturing. A palm oil-based lapping solution was compared with grease and industrial lapping solutions. Lapping processes were conducted on cylindrical spur gear wheels following the Taguchi L27 experimental design, utilizing three distinct RPMs and varying times. The average surface roughness value after the lapping procedure diminished by 39.45% with the palm oil lapping solution, demonstrating greater effectiveness than the other treatments. The most significant percentage change among all lapping solutions was −59.06%, achieved with palm oil at 32 rpm for 10 min. On the other hand, the Taguchi L27 signal-to-noise analysis shows that the palm oil lapping solution yielded the optimal outcome at 50 rpm and 16 min. A palm oil-based lapping solution was seen as capable of replacing mineral oil-based lapping solutions.
- Open Access
- 28 March 2025
- Published by Turkish Journal of Forestry in Turkish Journal of Forestry | Türkiye Ormancılık Dergisi
- Vol. 26 (1) , 45-54
Ağaç İşleri Endüstrisindeki Çatı Makası Elemanlarında Farklı Bağlantı Elamanlarının Araştırılması
Bu çalışmada, geleneksel ahşap çatı sistemlerinde kullanılan mertek ve taban elemanlarının bağlantı noktalarındaki farklı birleştirme açıları (mertekte 90°, tabanda 90° ve açıortay) ile bu bağlantı noktalarının tespit edilmesinde kullanılan farklı bağlantı gereçlerine (Çivi, vida ve bulon) bağlı olarak; çatı makaslarının basınç emniyet gerilmeleri tespit edilmiştir. Yapılan çalışmada hava kurusu rutubet değeri %14, yoğunluk değeri 0.539 g/cm3, eğilme direnci 95.37 N/mm2, Eğilmede elastikiyet modülü değeri 10793,53 N/mm2 ve dinamik eğilme direnci değeri ise 16.142 kJ/m2 olan sedir (Cedrus libani A.Rich.) odunundan üretilen çatı makasındaki elemanların bağlantı noktalarında tespit edilen en yüksek basınç emniyet gerilmesi değerinin; bulon bağlantı gereci ve mertekte uygulanan 90°’lik açıya bağlı olarak 366.77 N/mm² olduğu tespit edilmiştir. En düşük basınç emniyet gerilmesi ise çivi bağlantı gereci ve mertekte uygulanan 90°’lik açıya bağlı olarak 38.93 N/mm² olarak tespit edilmiştir. Ayrıca yapılan çalışmada mertek ya da tabanda uygulanan 90°’lik birleştirme açıları arasında istatistiksel olarak anlamlı bir farkın olmadığı tespit edilmiştir. Elde edilen sonuçlara göre hem geniş açıklıklara ve hem de fazla yük taşıma potansiyeline sahip çatı sistemlerinde; mertek ya da tabanda 90°’lik birleştirme açılarının önemsiz olduğu fakat bağlantı gereci olarak bulon bağlantı gerecinin kullanılması önerilir. Bu çalışmanın diğer bir yönü ise çatı makasında meydana gelen basınç emniyet gerilmesinin tespitine yönelik uygulanan deneysel işlemler sonlu elemanlar metodu (FEM) ile de uygulanmıştır. Bu metoda göre ise vida bağlantılı mertek ve taban birleştirmelerinde kayma gerilmelerinin daha fazla olduğu tespit edilmiştir.
- 28 March 2025
- Published by Turkish Journal of Forestry in Turkish Journal of Forestry | Türkiye Ormancılık Dergisi
- Vol. 26 (1) , 45-54
Open AccessAğaç İşleri Endüstrisindeki Çatı Makası Elemanlarında Farklı Bağlantı Elamanlarının Araştırılması
Bu çalışmada, geleneksel ahşap çatı sistemlerinde kullanılan mertek ve taban elemanlarının bağlantı noktalarındaki farklı birleştirme açıları (mertekte 90°, tabanda 90° ve açıortay) ile bu bağlantı noktalarının tespit edilmesinde kullanılan farklı bağlantı gereçlerine (Çivi, vida ve bulon) bağlı olarak; çatı makaslarının basınç emniyet gerilmeleri tespit edilmiştir. Yapılan çalışmada hava kurusu rutubet değeri %14, yoğunluk değeri 0.539 g/cm3, eğilme direnci 95.37 N/mm2, Eğilmede elastikiyet modülü değeri 10793,53 N/mm2 ve dinamik eğilme direnci değeri ise 16.142 kJ/m2 olan sedir (Cedrus libani A.Rich.) odunundan üretilen çatı makasındaki elemanların bağlantı noktalarında tespit edilen en yüksek basınç emniyet gerilmesi değerinin; bulon bağlantı gereci ve mertekte uygulanan 90°’lik açıya bağlı olarak 366.77 N/mm² olduğu tespit edilmiştir. En düşük basınç emniyet gerilmesi ise çivi bağlantı gereci ve mertekte uygulanan 90°’lik açıya bağlı olarak 38.93 N/mm² olarak tespit edilmiştir. Ayrıca yapılan çalışmada mertek ya da tabanda uygulanan 90°’lik birleştirme açıları arasında istatistiksel olarak anlamlı bir farkın olmadığı tespit edilmiştir. Elde edilen sonuçlara göre hem geniş açıklıklara ve hem de fazla yük taşıma potansiyeline sahip çatı sistemlerinde; mertek ya da tabanda 90°’lik birleştirme açılarının önemsiz olduğu fakat bağlantı gereci olarak bulon bağlantı gerecinin kullanılması önerilir. Bu çalışmanın diğer bir yönü ise çatı makasında meydana gelen basınç emniyet gerilmesinin tespitine yönelik uygulanan deneysel işlemler sonlu elemanlar metodu (FEM) ile de uygulanmıştır. Bu metoda göre ise vida bağlantılı mertek ve taban birleştirmelerinde kayma gerilmelerinin daha fazla olduğu tespit edilmiştir.
- 12 December 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (10) , 1233-1249
Delamination and thrust force analysis in GLARE: Influence of tool geometry and prediction with machine learning models
The multi-layered (fiber/metal) structure of glass fibre aluminium reinforced epoxy (GLARE) makes it difficult to obtain acceptable damage-free holes that meet aerospace standards. This paper investigated the effects of tool geometry and drilling parameters on reducing delamination damage and uncut fibers at the hole exit surface in drilling GLARE. The hole surfaces were examined by scanning electron microscope (SEM) at various magnifications. In addition, deep neural network (DNN) and long-short-term memory (LSTM) machine learning models were used to predict delamination (F da ), uncut fiber (UCF), and thrust forces using experimental data. No positive contribution of the special geometry tool was observed, while the standard geometry tool was found to be ideal for drilling conditions. Analysis of variance (ANOVA) revealed that feed rate contributed 57.83% to delamination damage, while tool geometry contributed 74.31% and 92.33% for uncut fiber and thrust force, respectively. SEM analysis revealed high deformation zones in the aluminum layers and fiber fracture and separation in the glass fibre reinforced polymer (GFRP) layers. DNN and LSTM models were found to provide accurate predictions with R 2 values greater than 95% and 98%, respectively.
- 12 December 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 59 (10) , 1233-1249
Delamination and thrust force analysis in GLARE: Influence of tool geometry and prediction with machine learning models
The multi-layered (fiber/metal) structure of glass fibre aluminium reinforced epoxy (GLARE) makes it difficult to obtain acceptable damage-free holes that meet aerospace standards. This paper investigated the effects of tool geometry and drilling parameters on reducing delamination damage and uncut fibers at the hole exit surface in drilling GLARE. The hole surfaces were examined by scanning electron microscope (SEM) at various magnifications. In addition, deep neural network (DNN) and long-short-term memory (LSTM) machine learning models were used to predict delamination (F da ), uncut fiber (UCF), and thrust forces using experimental data. No positive contribution of the special geometry tool was observed, while the standard geometry tool was found to be ideal for drilling conditions. Analysis of variance (ANOVA) revealed that feed rate contributed 57.83% to delamination damage, while tool geometry contributed 74.31% and 92.33% for uncut fiber and thrust force, respectively. SEM analysis revealed high deformation zones in the aluminum layers and fiber fracture and separation in the glass fibre reinforced polymer (GFRP) layers. DNN and LSTM models were found to provide accurate predictions with R 2 values greater than 95% and 98%, respectively.