Sylvie Durand
Sylvie Durand has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Sofiane Guessasma
UR1268 Biopolymères Interactions Assemblages, INRAE, F-44316 Nantes, France
5 shared publications - Sofiane Belhabib
Université de Nantes, Oniris, CNRS, GEPEA, UMR 6144, F-44000 Nantes, France
4 shared publications - Nicolas Stephant
Institut des Matériaux de Nantes Jean Rouxel (IMN), Nantes Université, UMR 6502 CNRS, Nantes, 44322 France
3 shared publications - Lotfi Hedjazi
Institut de Recherche ESTP 28 Avenue du Président Wilson F-94230 Cachan France
2 shared publications Alain Bourmaud
1 shared publication- Alain Bourmaud
IRDL Laboratory, UMR CNRS 6027, Université Bretagne Sud, 56100 Lorient, France
1 shared publication
Latest Publications
- Open Access
Digital Light Processing Route for 3D Printing of Acrylate-Modified PLA/Lignin Blends: Microstructure and Mechanical Performance
In this study, digital light processing (DLP) was utilized to generate 3D-printed blends composed of photosensitive acrylate-modified polylactic acid (PLA) resin mixed with varying weight ratios of lignin extracted from softwood, typically ranging from 5 wt% to 30 wt%. The microstructure of these 3D-printed blends was examined through X-ray microtomography. Additionally, the tensile mechanical properties of all blends were assessed in relation to the weight ratio and post-curing treatment. The results suggest that post-curing significantly influences the tensile properties of the 3D-printed composites, especially in modulating the brittleness of the prints. Furthermore, an optimal weight ratio was identified to be around 5 wt%, beyond which UV light photopolymerization experiences compromises. These findings regarding acrylate-modified PLA/lignin blends offer a cost-effective alternative for producing 3D-printed bio-sourced components, maintaining technical performance in reasonable-cost, low-temperature 3D printing, and with a low environmental footprint.
Open AccessDigital Light Processing Route for 3D Printing of Acrylate-Modified PLA/Lignin Blends: Microstructure and Mechanical Performance
In this study, digital light processing (DLP) was utilized to generate 3D-printed blends composed of photosensitive acrylate-modified polylactic acid (PLA) resin mixed with varying weight ratios of lignin extracted from softwood, typically ranging from 5 wt% to 30 wt%. The microstructure of these 3D-printed blends was examined through X-ray microtomography. Additionally, the tensile mechanical properties of all blends were assessed in relation to the weight ratio and post-curing treatment. The results suggest that post-curing significantly influences the tensile properties of the 3D-printed composites, especially in modulating the brittleness of the prints. Furthermore, an optimal weight ratio was identified to be around 5 wt%, beyond which UV light photopolymerization experiences compromises. These findings regarding acrylate-modified PLA/lignin blends offer a cost-effective alternative for producing 3D-printed bio-sourced components, maintaining technical performance in reasonable-cost, low-temperature 3D printing, and with a low environmental footprint.
- Open Access
Effects of Microstructural Arrangement on the Mechanical Behavior of 3D Printed Polyamide
This study aims to relate the microstructural arrangement, in particular the symmetry materialized by filament sequencing in the fused filament fabrication process, to the mechanical behavior of printed polyamide. Dog-bone structures were printed using various printing temperatures ranging from 250 °C to 280 °C, which were combined with part orientation including vertical, horizontal, and lateral configurations and raster angles (0°, 15°, 30°, and 45°) that represent the in-plane and out-of-plane symmetrical arrangement of the filament. Mechanical testing was conducted on both as-received filaments and printed structures to derive the effects of filament arrangement symmetry and process-generated defects on mechanical loss. In addition, a microstructural analysis using scanning electron microscopy was used to share more light on the filament arrangements and their consequence on the deformation mechanisms with respect to the printing conditions. The results showed that the 3D printed polyamide-based materials exhibited remarkable tensile performance with strain stiffening behavior and large elongation at break due to their particular filament layout. Among the considered printing conditions, the part orientation was found to have the largest influence on the tensile behavior, which modulates the behavior from complete restoration of the filament performance to mechanical loss.
Open AccessEffects of Microstructural Arrangement on the Mechanical Behavior of 3D Printed Polyamide
This study aims to relate the microstructural arrangement, in particular the symmetry materialized by filament sequencing in the fused filament fabrication process, to the mechanical behavior of printed polyamide. Dog-bone structures were printed using various printing temperatures ranging from 250 °C to 280 °C, which were combined with part orientation including vertical, horizontal, and lateral configurations and raster angles (0°, 15°, 30°, and 45°) that represent the in-plane and out-of-plane symmetrical arrangement of the filament. Mechanical testing was conducted on both as-received filaments and printed structures to derive the effects of filament arrangement symmetry and process-generated defects on mechanical loss. In addition, a microstructural analysis using scanning electron microscopy was used to share more light on the filament arrangements and their consequence on the deformation mechanisms with respect to the printing conditions. The results showed that the 3D printed polyamide-based materials exhibited remarkable tensile performance with strain stiffening behavior and large elongation at break due to their particular filament layout. Among the considered printing conditions, the part orientation was found to have the largest influence on the tensile behavior, which modulates the behavior from complete restoration of the filament performance to mechanical loss.
- Open Access
- 8 November 2023
- Published by MDPI AG in Preprints.org
Effect of Microstructural Arrangement on Mechanical Behaviour of 3D Printed Polyamide
This study aims at relating the microstructural arrangement, in particular the symmetry materialised by filament sequencing in fused filament fabrication process on mechanical behaviour of printed polyamide. Dogbone structures are printed using various printing temperatures, which are combined with part orientation and raster angle that represent the in-plane and out-of-plane symmetrical arrangement of filament. Mechanical testing is conducted on both as-received filaments and printed structures to derive the effect of filament arrangement symmetry and process-generated defects on mechanical loss. In addition, microstructural analysis using scanning electron microscopy is used to share more light on the filament arrangement and their consequence on deformation mechanisms with respect to the printing conditions. The results show that 3D printed polyamide-based material exhibit remarkable tensile performance with strain stiffening behaviour and large elongation at break thanks to particular filament layout. Among the considered printing conditions, the part orientation is found to have the largest influence on tensile behaviour, which modulates the behaviour from complete restoration of the filament performance to mechanical loss.
- 8 November 2023
- Published by MDPI AG in Preprints.org
Open AccessEffect of Microstructural Arrangement on Mechanical Behaviour of 3D Printed Polyamide
This study aims at relating the microstructural arrangement, in particular the symmetry materialised by filament sequencing in fused filament fabrication process on mechanical behaviour of printed polyamide. Dogbone structures are printed using various printing temperatures, which are combined with part orientation and raster angle that represent the in-plane and out-of-plane symmetrical arrangement of filament. Mechanical testing is conducted on both as-received filaments and printed structures to derive the effect of filament arrangement symmetry and process-generated defects on mechanical loss. In addition, microstructural analysis using scanning electron microscopy is used to share more light on the filament arrangement and their consequence on deformation mechanisms with respect to the printing conditions. The results show that 3D printed polyamide-based material exhibit remarkable tensile performance with strain stiffening behaviour and large elongation at break thanks to particular filament layout. Among the considered printing conditions, the part orientation is found to have the largest influence on tensile behaviour, which modulates the behaviour from complete restoration of the filament performance to mechanical loss.
- Open Access
- 5 July 2023
- Published by Elsevier in Composites Part C: Open Access
- Vol. 12
Combining infrared and Raman spectra to assess MDI localization in novel flax-reinforced automotive composites
- 5 July 2023
- Published by Elsevier in Composites Part C: Open Access
- Vol. 12
Open AccessCombining infrared and Raman spectra to assess MDI localization in novel flax-reinforced automotive composites
- Open Access
Synthesis of a Starchy Photosensitive Material for Additive Manufacturing of Composites Using Digital Light Processing
In this study, digital light processing (DLP) was used to achieve 3D-printed composite materials containing photosensitive resin blended with starch and hemp fibers. The synthesis of 3D-printed composites was performed without heating, according to various material combinations ranging from pure photosensitive resin to a mixture of three phases, including resin, starch, and hemp fibers, with the weight content for each reinforcing phase reaching up to a third of the formulation. The morphology, composition, and structure of the 3D-printed composites were assessed using infrared spectroscopy, laser granulometry, X-ray diffraction, and optical and scanning electron microscopy. In addition, thermal behavior and mechanical performance were studied using calorimetry, differential scanning calorimetry, and tensile testing combined with high-speed optical imaging. The results showed that the post-curing step is a leading factor for improving the mechanical performance of the 3D-printed composites. In addition, hemp fiber or starch did not alter the tensile strength. However, the largest reinforcing effect in terms of stiffness improvement was obtained with starch. Additionally, starchy composites demonstrated the strongest dependence of heat capacity on operating temperature.
Open AccessSynthesis of a Starchy Photosensitive Material for Additive Manufacturing of Composites Using Digital Light Processing
In this study, digital light processing (DLP) was used to achieve 3D-printed composite materials containing photosensitive resin blended with starch and hemp fibers. The synthesis of 3D-printed composites was performed without heating, according to various material combinations ranging from pure photosensitive resin to a mixture of three phases, including resin, starch, and hemp fibers, with the weight content for each reinforcing phase reaching up to a third of the formulation. The morphology, composition, and structure of the 3D-printed composites were assessed using infrared spectroscopy, laser granulometry, X-ray diffraction, and optical and scanning electron microscopy. In addition, thermal behavior and mechanical performance were studied using calorimetry, differential scanning calorimetry, and tensile testing combined with high-speed optical imaging. The results showed that the post-curing step is a leading factor for improving the mechanical performance of the 3D-printed composites. In addition, hemp fiber or starch did not alter the tensile strength. However, the largest reinforcing effect in terms of stiffness improvement was obtained with starch. Additionally, starchy composites demonstrated the strongest dependence of heat capacity on operating temperature.
- 8 April 2022
- Published by Elsevier in Bioresource Technology
- Vol. 353, 127140
Real-time imaging of enzymatic degradation of pretreated maize internodes reveals different cell types have different profiles
- 8 April 2022
- Published by Elsevier in Bioresource Technology
- Vol. 353, 127140
Real-time imaging of enzymatic degradation of pretreated maize internodes reveals different cell types have different profiles
- 1 February 2022
- Published by Elsevier in Carbohydrate Polymers
- Vol. 278, 118942
Structure of heteroxylans from vitreous and floury endosperms of maize grain and impact on the enzymatic degradation
- 1 February 2022
- Published by Elsevier in Carbohydrate Polymers
- Vol. 278, 118942
Structure of heteroxylans from vitreous and floury endosperms of maize grain and impact on the enzymatic degradation
- Open Access
Novel Insight into the Intricate Shape of Flax Fibre Lumen
Plant fibres and especially flax can be distinguished from most synthetic fibres by their intricate shape and intrinsic porosity called lumen, which is usually assumed to be tubular. However, the real shape appears more complex and thus might induce stress concentrations influencing the fibre performance. This study proposes a novel representation of flax fibre lumen and its variations along the fibre, an interpretation of its origin and effect on flax fibre tensile properties. This investigation was conducted at the crossroads of complementary characterization techniques: optical and scanning electron microscopy (SEM), high-resolution X-ray microtomography (µCT) and mechanical tests at the cell-wall and fibre scale by atomic force microscopy (AFM) in Peak-Force Quantitative Nano-Mechanical property mapping (PF-QNM) mode and micromechanical tensile testing. Converging results highlight the difficulty of drawing a single geometric reference for the lumen. AFM and optical microscopy depict central cavities of different sizes and shapes. Porosity contents, varying from 0.4 to 7.2%, are estimated by high-resolution µCT. Furthermore, variations of lumen size are reported along the fibres. This intricate lumen shape might originate from the cell wall thickening and cell death but particular attention should also be paid to the effects of post mortem processes such as drying, retting and mechanical extraction of the fibre as well as sample preparation. Finally, SEM observation following tensile testing demonstrates the combined effect of geometrical inhomogeneities such as defects and intricate lumen porosity to drive the failure of the fibre.
Open AccessNovel Insight into the Intricate Shape of Flax Fibre Lumen
Plant fibres and especially flax can be distinguished from most synthetic fibres by their intricate shape and intrinsic porosity called lumen, which is usually assumed to be tubular. However, the real shape appears more complex and thus might induce stress concentrations influencing the fibre performance. This study proposes a novel representation of flax fibre lumen and its variations along the fibre, an interpretation of its origin and effect on flax fibre tensile properties. This investigation was conducted at the crossroads of complementary characterization techniques: optical and scanning electron microscopy (SEM), high-resolution X-ray microtomography (µCT) and mechanical tests at the cell-wall and fibre scale by atomic force microscopy (AFM) in Peak-Force Quantitative Nano-Mechanical property mapping (PF-QNM) mode and micromechanical tensile testing. Converging results highlight the difficulty of drawing a single geometric reference for the lumen. AFM and optical microscopy depict central cavities of different sizes and shapes. Porosity contents, varying from 0.4 to 7.2%, are estimated by high-resolution µCT. Furthermore, variations of lumen size are reported along the fibres. This intricate lumen shape might originate from the cell wall thickening and cell death but particular attention should also be paid to the effects of post mortem processes such as drying, retting and mechanical extraction of the fibre as well as sample preparation. Finally, SEM observation following tensile testing demonstrates the combined effect of geometrical inhomogeneities such as defects and intricate lumen porosity to drive the failure of the fibre.