Zhuobin Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zhuobin Zhao has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jun Li
Institute of Turbomachinery, School of Energy & Power Engineering, Xi'an Jiaotong University , Xi'an 710049, China
2 shared publications - Qinghua Deng
Xi'an Jiaotong University, China
2 shared publications - Zhenping Feng
School of Energy and Power Engineering, Xi'an Jiaotong University , Xi'an 710049, China
2 shared publications - Bing Tang
Nanjing Engineering Institute of Aircraft Systems, AVIC, Nanjing 211106, China
1 shared publication - Jianxin Liao
Dongfang Turbine Co., Ltd., Dongfang Electric Corporation, Deyang 618000, China
1 shared publication - Lehao Hu
Shaanxi Engineering Laboratory of Turbomachinery and Power Equipment, Institute of Turbomachinery, School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication
Latest Publications
- Open Access
- 27 March 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (7) , 3678
Windage and Leakage Losses in Impeller Back Gap and Labyrinth Seal Cavities of Supercritical CO2 Centrifugal Compressors
The windage loss in impeller back gap and labyrinth seal cavities significantly impacts the aerodynamic performances of supercritical carbon dioxide (sCO2) compressors. To accurately calculate windage loss, essential factors affecting the skin friction coefficients Cf,d (disk-type gap) and Cf,s (shaft-type gap), including Reynolds number Re, pressure ratio π, and radius ratio η, are investigated in this paper. The flow characteristics of the gap are analyzed and prediction models are proposed. The results indicate that both Cf,d and Cf,s decrease with increasing Re and grow with π and η, attributable to expanded high-vorticity regions caused by enhanced flow instability and larger vortices. The leakage flow rate m is unchanged for Re < 106 since the fluid can flow into the impeller back gap, and slightly decreases for Re ≥ 106 due to the centrifugal force and the inhibition effect of the vortices filling inlet regions. Moreover, the m grows with π and η due to a larger pressure difference and through-flow area. Maximal relative deviations of 6.23% and 6.83% can satisfy the requirements for calculating accurate windage loss in the impeller back gap and labyrinth seal cavities, which help the primary design of sCO2 compressors.
- 27 March 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (7) , 3678
Open AccessWindage and Leakage Losses in Impeller Back Gap and Labyrinth Seal Cavities of Supercritical CO2 Centrifugal Compressors
The windage loss in impeller back gap and labyrinth seal cavities significantly impacts the aerodynamic performances of supercritical carbon dioxide (sCO2) compressors. To accurately calculate windage loss, essential factors affecting the skin friction coefficients Cf,d (disk-type gap) and Cf,s (shaft-type gap), including Reynolds number Re, pressure ratio π, and radius ratio η, are investigated in this paper. The flow characteristics of the gap are analyzed and prediction models are proposed. The results indicate that both Cf,d and Cf,s decrease with increasing Re and grow with π and η, attributable to expanded high-vorticity regions caused by enhanced flow instability and larger vortices. The leakage flow rate m is unchanged for Re < 106 since the fluid can flow into the impeller back gap, and slightly decreases for Re ≥ 106 due to the centrifugal force and the inhibition effect of the vortices filling inlet regions. Moreover, the m grows with π and η due to a larger pressure difference and through-flow area. Maximal relative deviations of 6.23% and 6.83% can satisfy the requirements for calculating accurate windage loss in the impeller back gap and labyrinth seal cavities, which help the primary design of sCO2 compressors.
- Open Access
- 15 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10354
Skin-Friction Coefficient Model Verification and Flow Characteristics Analysis in Disk-Type Gap for Radial Turbomachinery
Under the conditions of high speed and density flow, the windage loss in the gap behind an impeller has an important influence on its thermal power conversion efficiency. Daily and Nece took the relative gap and Reynolds number as the characteristic parameters and divided the flow of a rotating disk in a closed chamber into four flow regions through laminar flow, turbulent flow and state of boundary layers. In this paper, the skin-friction coefficient model of Regio III and IV was verified by a numerical method under conditions corresponding to the typical Reynolds number range for a radial impeller. The results show that when the relative gap increases, the relative deviation between the numerical calculation and the model prediction results decreases, and the maximum deviation is −12.4%. With the increase of Reynolds number, the Region IV model is more accurate. Region III has the flow state of boundary layers merging and separation at the same time. Both models have good prediction accuracy with different mediums of air, water-liquid and critical CO2. The deviation in Region III is larger and shows a decreasing trend with respect to Region IV, Based on the two models, a method for predicting the optimal gap is proposed. The method is verified to be reliable and can minimize windage loss.
- 15 September 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (18) , 10354
Open AccessSkin-Friction Coefficient Model Verification and Flow Characteristics Analysis in Disk-Type Gap for Radial Turbomachinery
Under the conditions of high speed and density flow, the windage loss in the gap behind an impeller has an important influence on its thermal power conversion efficiency. Daily and Nece took the relative gap and Reynolds number as the characteristic parameters and divided the flow of a rotating disk in a closed chamber into four flow regions through laminar flow, turbulent flow and state of boundary layers. In this paper, the skin-friction coefficient model of Regio III and IV was verified by a numerical method under conditions corresponding to the typical Reynolds number range for a radial impeller. The results show that when the relative gap increases, the relative deviation between the numerical calculation and the model prediction results decreases, and the maximum deviation is −12.4%. With the increase of Reynolds number, the Region IV model is more accurate. Region III has the flow state of boundary layers merging and separation at the same time. Both models have good prediction accuracy with different mediums of air, water-liquid and critical CO2. The deviation in Region III is larger and shows a decreasing trend with respect to Region IV, Based on the two models, a method for predicting the optimal gap is proposed. The method is verified to be reliable and can minimize windage loss.