LHLehao Hu

Lehao Hu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lehao Hu has a total of 8 co-authors. Here are the top co-authors by number of shared publications:

  • Qinghua Deng

    Xi'an Jiaotong University, China

    3 shared publications
  • Zhenping Feng

    School of Energy and Power Engineering, Xi'an Jiaotong University , Xi'an 710049, China

    3 shared publications
  • Jun Li

    Institute of Turbomachinery, School of Energy & Power Engineering, Xi'an Jiaotong University , Xi'an 710049, China

    2 shared publications
  • Qi Yuan

    Shaanxi Engineering Laboratory of Turbomachinery and Power Equipment, Institute of Turbomachinery, School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China

    1 shared publication
  • Wenjiao Qi

    Shaanxi Engineering Laboratory of Turbomachinery and Power Equipment, Institute of Turbomachinery, School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China

    1 shared publication
  • Zhinan Chi

    Shaanxi Engineering Laboratory of Turbomachinery and Power Equipment, Institute of Turbomachinery, School of Energy and Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China

    1 shared publication

Latest Publications

  • Open Access

    Skin-Friction Coefficient Model Verification and Flow Characteristics Analysis in Disk-Type Gap for Radial Turbomachinery

    by Zhuobin Zhao, Qinghua Deng, Lehao Hu, Jun Li, Zhenping Feng

    Under the conditions of high speed and density flow, the windage loss in the gap behind an impeller has an important influence on its thermal power conversion efficiency. Daily and Nece took the relative gap and Reynolds number as the characteristic parameters and divided the flow of a rotating disk in a closed chamber into four flow regions through laminar flow, turbulent flow and state of boundary layers. In this paper, the skin-friction coefficient model of Regio III and IV was verified by a numerical method under conditions corresponding to the typical Reynolds number range for a radial impeller. The results show that when the relative gap increases, the relative deviation between the numerical calculation and the model prediction results decreases, and the maximum deviation is −12.4%. With the increase of Reynolds number, the Region IV model is more accurate. Region III has the flow state of boundary layers merging and separation at the same time. Both models have good prediction accuracy with different mediums of air, water-liquid and critical CO2. The deviation in Region III is larger and shows a decreasing trend with respect to Region IV, Based on the two models, a method for predicting the optimal gap is proposed. The method is verified to be reliable and can minimize windage loss.


  • Open Access

    Effects of Surface Roughness on Windage Loss and Flow Characteristics in Shaft-Type Gap with Critical CO2

    by Lehao Hu, Qinghua Deng, Zhouyang Liu, Jun Li, Zhenping Feng

    To investigate the effects of surface roughness on windage loss and flow characteristics in a shaft-type gap, the skin friction coefficient (Cf) and flow versus Reynolds number (Re) at different surface roughness (Ra) and radius ratio (η) values were investigated. The results showed that Cf decreased as Re increased, and the rate of decrease was constant at low Re but reduced at high Re. The growing relative deviations between the coefficients of smooth and rough walls with Ra indicated that Cf was influenced by rough walls when Re > 102. Moreover, Cf and the variation rate increased with η and were easily influenced by Ra for larger η at low Re, since the interaction between wall roughness and fluid influences windage loss. In addition, the flow field implied the flow had transitioned to Taylor-Couette flow, Taylor vortexes occurred when Re > 102, and the number of vortexes increased with increasing Ra and were reduced with increasing η. The velocity was divided into three regions and the pressure rose from the rotational to stationary walls, but decreased with growing η as a whole. This paper improves the research exploring windage loss and will help design smaller supercritical CO2 power devices.


  • Open Access

    Influence of Disc Tip Geometry on the Aerodynamic Performance and Flow Characteristics of Multichannel Tesla Turbines

    by Wenjiao Qi, Qinghua Deng, Zhinan Chi, Lehao Hu, Qi Yuan, Zhenping Feng

    As a competitive small-scale turbomachinery option, Tesla turbines have wide potential in various fields, such as renewable energy generation systems and small power equipment. This paper investigates the influence of disc tip geometry, including its profile and relative height, on the aerodynamic performance and flow characteristics of one-to-one and one-to-many multichannel Tesla turbines. The results indicate that compared to the turbine with blunt tips, the isentropic efficiency of the one-to-one turbine with sharp tips has a little decrease, which is because the relative tangential velocity gradient near the rotational disc walls decreases a little and additional vortices are generated at the rotor inlet, while that of the one-to-many turbine with sharp tips increases significantly, resulting from an increase in the relative tangential velocity in the disc channels and a decrease in the low Mach number and vortex area; for instance the turbine efficiency for the former relatively decreases by 3.6% and that for the latter increases by 13.5% at 30,000 r/min. In addition, the isentropic efficiency of the one-to-many turbine with sharp tips goes up with increasing relative height due to increasing improvement of flow status, and its increment rate slows down. A circular or elliptic tip performs better with lower relative height and a triangular tip behaves better with higher relative height. To sum up, a blunt disc tip is recommended for the one-to-one turbine, and a sharp disc tip is for the one-to-many turbine. The relative height and tip profile of the one-to-many turbine should be determined according to their effects on turbine performance, manufacturing difficulty and mechanical deformation.