QLQifei Li

Qifei Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Qifei Li has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Study on the Correlation Between Unstable Flow and Cavitation Vibration of Pump-Wheel Cascade

    by Ling Li, Qifei Li, Feng Zhou

    In order to deeply reveal the coupling mechanism of flow and cavitation evolution inside the pump–turbine under hump conditions, this paper combines numerical simulation of multiphase flow with high-speed imaging experiments and systematically analyzes the structure of non-constant flow and its induced hydraulic excitation behavior. It is found that as the cavitation number decreases from 0.33 to 0.072, the vacuole morphology in the impeller develops from incipient bright spots to U-shaped cavitation clouds, and vortex cavitation and lamellar cavitation meet at the trailing edge, which triggers a strong perturbation in the flow channel. At the same time, large-scale flow separation develops on the pressure surface, accompanied by intensified vortex structures on the suction surface and a highly non-uniform circumferential velocity distribution at the guide-vane inlet. These flow distortions significantly increase the hydraulic excitation of the system. The three-dimensional connection and asymmetric distribution of the vacuoles exacerbate the load imbalance between the channels, which is the main cause of efficiency loss and structural vibration enhancement. The pressure pulsation spectrum is accompanied by multiple high-frequency and low-frequency excitation peaks, especially in the 20–33 Hz band, which reveals the multi-source coupling mechanism between cavitation behavior, reflux shear, and modal response. The results provide theoretical support for the in-depth understanding of the instability evolution mechanism of the pump–turbine and operation optimization under complex working conditions.

  • Open Access

    Study on the Coupling Characteristics Between Unsteady Flow and Hydrodynamic Loads in the Guide Vane Region of a Pump–Turbine Under Runaway Condition

    by Ling Li, Qifei Li, Xiangyu Chen

    To elucidate the coupling characteristics between unsteady flow and hydrodynamic loads in the guide vane region of a pump–turbine under runaway conditions, a model pump–turbine of a high-head pumped storage power station was selected as the research object. A combined approach of model experiments and three-dimensional unsteady numerical simulations was employed to investigate the guide vane hydraulic torque, flow field structures, pressure distribution, and pressure fluctuation characteristics under different pre-opening guide vane conditions. In the experiments, the hydraulic torque of guide vanes was measured using a guide vane shaft strain testing method at five guide vane openings of 19 mm, 25 mm, 33 mm, 41 mm, and 45 mm. In the numerical simulations, a full-passage unsteady computational model was established based on the SST k-ω turbulence model, and the reliability of the numerical model was validated against experimental results. The results indicate that the guide vane hydraulic torque under runaway conditions exhibits pronounced periodic fluctuations, and the dominant period in the time domain is consistent with the blade passing frequency, demonstrating that rotor–stator interaction between the runner wake and guide vanes is the primary mechanism inducing unsteady hydraulic loads. As the guide vane opening decreases, the flow passage area in the guide vane region is reduced, and the high-speed swirling flow at the runner outlet generates significant jet impingement and local shear layers near the guide vane inlet, resulting in enhanced circumferential non-uniformity of the flow field and a substantial increase in the pressure difference across the guide vane surfaces. Among all operating conditions, the hydraulic torque fluctuation at a0 = 19 mm is the most severe. Under small-opening conditions, flow separation, wake accumulation, and local backflow structures are prone to occur in the vicinity of the guide vanes, accompanied by pronounced high-frequency pressure disturbances and local impulsive pressure peaks. With increasing guide vane opening, the flow attachment behavior and flow field continuity are gradually improved, and the pressure fluctuations evolve from random oscillations to regular periodic pulsations, indicating a significant enhancement in flow stability. The study demonstrates that small guide vane opening conditions produce hydrodynamic load characteristics—specifically, higher-amplitude and more intermittent torque fluctuations, as well as lower minimum pressures—that are indicative of conditions conducive to increased vibration, fatigue accumulation, and cavitation risk; however, direct structural or two-phase cavitation analyses are required to confirm these implications. The present results can provide a theoretical basis for the optimal design of guide vane mechanisms and the safe operation of pump–turbines under runaway conditions, and quantitative coupling analysis reveals that the cross-correlation between inlet pressure and torque decreases from R = 0.87 at a0 = 19 mm to R = 0.72 at a0 = 45 mm, confirming that the flow–load coupling weakens substantially with increasing opening.

  • Open Access

    Coupling Mechanisms Between Vortex Rope Evolution and Cavitation Within the Draft Tube of Pump-turbines

    by L. Xin, Q. Li, S. Zhang

    A technique integrating numerical simulations with experimental observations was hereby employed to elucidate the flow instability mechanisms during transient processes in pump-turbines, and a reversible pump-turbine was investigated for in-depth insights. Concurrently, the coupling phenomena between vortex rope and cavitation under transient conditions were systematically analysed. The results indicate that rotational and pressure gradients predominantly drive the vortex rope evolution, thereby exerting a substantial influence on cavitation development. The formation and collapse of low-pressure cavities disrupt the vortex structures while intensifying the flow instability. High tangential momentum as well as shear layers contribute to forming alternating vortex structures. Cavitation bubbles are either entrained by the vortex rope or diffuse outward, resulting in pronounced fluctuations in cavity volume. As the vortex structure evolves, it gradually transitions downstream into a more stable, axisymmetric configuration. Pressure fluctuation analysis reveals that low-frequency oscillations within the straight conical section are predominantly induced by vortex rope rotation and cavitation collapse. In the elbow region, localized pressure amplification arises from vortex-wall interactions, while the axial non-uniformity of vortex ropes and cavity distribution governs the spatial variability of pressure pulsations. Collectively, this study establishes a theoretical basis for understanding the coupling between vortex ropes and cavitation. It further offers practical guidance for controlling vortex dynamics and mitigating cavitation in engineering applications.


  • Open Access

    Flow Characteristics of Bulb Tubular Turbine Based on Solid-liquid Two-phase Flow Model

    by Q. Li, F. Zhou, Q. Wang

    This study examines the operational efficiency of a bulb tubular turbine under solid-liquid two-phase (SLTP) flow conditions. By employing the Euler-Euler method, the characteristics of SLTP flow in the turbine with different solid particle diameters were analyzed. The research findings demonstrate that the increase in solid particle diameter from 0.01 mm to 0.15 mm decreases the maximum liquid phase velocity in the XY plane by approximately 0.26%. The introduction of solid particles results in increased likelihood of cavitation and vortices in the draft tube region, leading to diminished energy recovery efficiency in this area. Within the impeller domain, regions with high solid particle concentration are predominantly located on the blade front hub and inlet edge, while the blade's rear side exhibits an overall higher concentration. Further analysis reveals a positive correlation between blade velocity/concentration distribution and the diameter of solid particles. Furthermore, particle size has a significant impact on the solid phase trajectory and solid phase velocity in the draft tube area. Particles with larger diameters tend to move in more irregular and chaotic patterns, promoting the formation of vortices in the draft tube region. Notably, while the velocity of the solid phase at the draft tube inlet decreases with increasing particle size, the velocity fluctuations within the draft tube become more pronounced. Among the different flow components of the hydraulic turbine, the wear severity follows a descending order: the blade region experiences the highest wear, followed by the runner chamber, guide vane area, and draft tube region. Additionally, the diameter of the solid phase shows a positive correlation with both the wear area and the maximum wear rate in the runner chamber, blade region, and guide vane area, whereas it demonstrates a negative correlation with wear in the draft tube region.


  • Open Access

    Cavitation Performance Analysis in the Runner Region of a Bulb Turbine

    by Feng Zhou, Qifei Li, Lu Xin, Xiangyu Chen, Shiang Zhang, Yuqian Qiao

    As a core component in renewable energy systems for grid regulation, hydropower units are increasingly exposed to flow conditions that elevate the risk of cavitation and erosion, posing significant challenges to the safe operation of flow-passage components. In this study, model testing and computational fluid dynamics (CFD) simulations are employed to investigate the hydraulic performance and cavitation behavior of a bulb turbine operating under rated head conditions and varying cavitation numbers. The analysis focuses on how changes in cavitation intensity affect flow characteristics and efficiency within the runner region. The results show that as the cavitation number approaches its critical value, the generation, growth, and collapse of vapor cavities increasingly disturb the main flow, causing a marked drop in blade hydraulic performance and overall turbine efficiency. Cavitation predominantly occurs on the blade’s suction side near the trailing edge rim and in the clearance zone near the hub, with bubble coverage expanding as the cavitation number decreases. A periodic inverse correlation between surface pressure and the cavitation area is observed, reflecting the strongly unsteady nature of cavitating flows. Furthermore, lower cavitation numbers lead to intensified pressure pulsations, aggravating flow unsteadiness and raising the risk of vibration.


  • Open Access

    A Study on the Transient Flow Characteristics of Pump Turbines Across the Full Operating Range in Turbine Mode

    by Hongqiang Tang, Qifei Li, Xiangyu Chen, Zhanyong Li, Shiwei Li

    The transient operation of pump turbines generates significant flow-induced instabilities, prompting a comprehensive numerical investigation using the SST k−ω turbulence model to examine these instability effects throughout the complete operating range in turbine mode. This study specifically analyzes the evolutionary mechanisms of unsteady flow dynamics under ten characteristic off-design conditions while simultaneously characterizing the pressure fluctuation behavior within the vaneless space (VS). The results demonstrate that under both low-speed conditions and near-zero-discharge conditions, the VS and its adjacent flow domains exhibit pronounced flow instabilities with highly turbulent flow structures, while the pressure fluctuation amplitudes remain relatively small due to insufficient rotational speed or flow rate. Across the entire turbine operating range, the blade passing frequency (BPF) dominates the VS pressure fluctuation spectrum. Significant variations are observed in both low-frequency components (LFCs) and high-frequency, low-amplitude components (HF-LACs) with changing operating conditions. The HF-LACs exhibit relatively stable amplitudes but demonstrate significant variation in the frequency spectrum distribution across different operating conditions, with notably broader frequency dispersion under runaway conditions and adjacent operating points. The LFCs demonstrate significantly higher spectral density and amplitude magnitudes under high-speed, low-discharge operating conditions while exhibiting markedly reduced occurrence and diminished amplitudes in the low-speed, high-flow regime. This systematic investigation provides fundamental insights into the flow physics governing pump-turbine performance under off-design conditions while offering practical implications for optimizing transient operational control methodologies in hydroelectric energy storage systems.


  • Open Access

    Effect of Guide Vane Opening on Flow Distortion and Impeller Stress in a Pump-Turbine Under Extremely Low-Head Conditions

    by Xiangyu Chen, Qifei Li, Lu Xin, Shiang Zhang, Mingjie Cheng, Tianding Han

    Under extremely low-head conditions, the performance and stability of pump-turbine units are strongly influenced by the flow distortion caused by variations in guide vane opening. In this study, a pump-turbine model—representative of a domestic pumped storage power station—was investigated through a combination of experimental observations and three-dimensional unsteady numerical simulations employing the SST k-ω turbulence model. The analysis focused on characterizing the variations in turbulence kinetic energy, pressure pulsations, and impeller force fluctuations as the guide vane opening was altered. The results reveal that, with increasing guide vane opening, the turbulence kinetic energy within the impeller region is notably reduced. This reduction is primarily attributed to a decrease in energy losses along the suction surfaces of the blades and within the straight pipe section of the tailwater tunnel. Simultaneously, pressure pulsations were detected at multiple locations including the volute inlet, the blade-free zone, downstream of the conical pipe, and along the inner surface of the shaft tube. While most regions experienced a decline in pressure pulsation intensity with larger openings, the bladeless zone exhibited a significant increase. Moreover, force analysis at four distinct guide vane settings indicated that an opening of 41 mm resulted in relatively uniform fluctuations in the impeller forces. This uniformity suggests that an optimal guide vane configuration exists, which minimizes uneven stress distributions and enhances the operational stability of the pump-turbine under extremely low-head conditions. These findings offer valuable insights for the design and operational optimization of pump-turbine systems in pumped storage power stations.


  • Open Access

    Study on the Influence of Reynolds Number on Heat Exchange Performance and Nusselt Number of Spray Coil Heat Exchanger

    by Tianding Han, Qifei Li, Lin Shang, Xiangyu Chen, Feng Zhou, Wangxu Li

    Biomass clean energy is widely used as an alternative to fossil fuels due to its advantages of low carbon emissions, cleanliness, and renewability. Biomass fuel exchangers are important equipment for heat exchange between air and exhaust gasses after biomass combustion, and the air flow rate and structural characteristics of the exchanger have a significant impact on the heat transfer performance. In order to investigate the effect of Reynolds number on the heat transfer performance of the exchanger when air flows through, a serpentine tube heat exchange test bench was constructed, and numerical calculations were performed using the Realizable k-ε turbulence model for the entire channel. By changing the diameter and pitch of the serpentine tube, the effects of geometric parameters on the heat transfer performance were studied, and the flow characteristics of exhaust gasses and air inside the exchanger under various operating conditions were deduced. Subsequently, experimental validation was conducted by referring to the boundary conditions of numerical calculations, obtaining corresponding test data, and comparing the numerical and experimental results, showing that the errors in various physical quantities were within 5%. Through comprehensive analysis of the data, it was found that when the serpentine tube diameter is 80 mm and pitch is 300 mm, the Nusselt number (Nu) increased most significantly with Reynolds number (Re) by 25.17%, indicating the best heat transfer performance. Additionally, reducing tube diameter, increasing serpentine tube pitch, enlarging air-inlet flow velocity can enhance Re, increase fluid disturbance, and improve convective heat transfer intensity, thereby increasing Nu and strengthening the heat transfer performance of the serpentine tube exchanger.


  • Open Access

    Cavitation Performance Analysis of Tip Clearance in a Bulb-Type Hydro Turbine

    by Feng Zhou, Qifei Li, Lu Xin, Shiang Zhang, Yang Liu, Ming Guo

    Bulb-type hydro turbines are commonly used in small- to medium-scale hydropower stations due to their compact design and adaptability to low-head conditions. However, long-term operation often results in wear at the runner rim, increasing tip clearance and triggering leakage flow and cavitation. These effects reduce hydraulic efficiency and accelerate blade surface erosion, posing serious risks to unit safety and operational stability. This study investigates the influence of tip clearance on cavitation performance in a 24 MW prototype bulb turbine. A three-dimensional numerical model is developed to simulate various operating conditions with different tip clearance values (3.0, 4.5, and 6.0 mm) and cavitation numbers (σ = 1.20–1.33). Internal flow characteristics—including pressure distribution, velocity fields, hydraulic efficiency, and pressure pulsation—are analyzed to elucidate the impact of tip clearance on cavitation development. Results show that under σ = 1.2 and a 4.5 mm tip clearance, the pressure pulsation amplitude at the blade tip reaches 4870 Pa—approximately 1.5 times higher than that near the hub. At partial flow conditions, turbine efficiency decreases by up to 6.8% compared to the rated condition. Increasing the tip clearance from 1.5 to 6.0 mm expands the low-pressure area near the blade tip by around 32%, significantly intensifying cavitation. Frequency domain analysis reveals dominant pulsation frequencies between 10–20 Hz, characterized by blade-passing features and a wave-clipping effect. These findings provide theoretical insight and quantitative evidence to support the optimization of tip clearance design and cavitation mitigation strategies in bulb turbines, aiming to improve both efficiency and operational stability.


  • Open Access

    Impact of Outlet Pressure on Internal Flow Characteristics and Energy Loss in Pump-Turbine System Under Pump Operation Conditions

    by Tianding Han, Qifei Li, Licheng Feng, Xiangyu Chen, Feng Zhou, Zhenggui Li

    During pump operation, the pump-turbine system experiences unstable fluctuations in outlet pressure, which induces turbulence and additional energy losses. Understanding the impact of outlet pressure variations on the internal flow field is crucial for the further development of turbine units. This study employs numerical methods to systematically analyze the effects of outlet pressure changes on flow characteristics and energy loss. The results show that a decrease in outlet pressure to P0.9BEP significantly increases entropy production in the double-row stay guide vane region, primarily due to flow separation and vortex formation. In the flow passage, sealing gap, and tailpipe regions, entropy production is mainly driven by wall effects, while secondary flows influence the spiral case. The vortex distribution in the double-row stay guide vane is complex, with different variation trends observed in the active and fixed guide vane regions. Outlet pressure changes affect the interaction between the flow passage blades and the fluid, leading to localized flow separation and directly impacting energy loss in downstream components. Additionally, the rate of change in outlet pressure significantly influences vortex generation and dissipation. This research provides new theoretical insights and research directions for performance optimization and energy loss control in pump-turbine systems.