Yuchao Zhao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuchao Zhao has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Qudong Wang
National Engineering Research Center of Light Alloy Net Forming, State Key Laboratory of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
7 shared publications - Mahmoud Ebrahimi
University of Maragheh
5 shared publications - Qiang Lu
National Engineering Research Center of Light Alloy Net Forming, State Key Laboratory of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
3 shared publications - Shokouh Attarilar
Department of Materials Engineering, Faculty of Engineering, University of Maragheh, Maragheh 83111-55181, Iran
3 shared publications - Dezhi Li
Warwick Manufacturing Group, University of Warwick, Coventry CV4 7AL, UK
2 shared publications - Huisheng Cai
School of Material Science and Engineering, Inner Mongolia University of Technology, Hohhot 010051, China
2 shared publications
Latest Publications
- Open Access
Tailoring Interfacial Bonding and Tensile Properties in Cu/Al/Cu Laminated Composites by Adjusting Thickness Ratio
The design of the overall thickness and thickness ratio in multilayered composites is vital because it affects interfacial microstructures and mechanical properties. These elements are significant in the application of multilayered composites in diverse scenarios. This study systematically investigated the interfacial microstructure, mechanical properties, and fracture mechanisms of Cu/Al/Cu trilayered composites with varying overall thicknesses and copper thickness ratios. The microstructure results showed that the distribution and thickness of intermetallic compounds (IMCs) at the Cu/Al interface changed significantly with different thickness designs. As the Cu thickness ratio increased from 20% to 35%, the intermetallic layer transitioned from a continuous structure to a fragmented one in both the 1 mm and 2 mm composites. Additionally, the bonding mechanism evolved from primarily metallurgical bonding to a combination of metallurgical and mechanical bonding. In the 4 mm composite with a 35% Cu thickness ratio, the interfacial intermetallic layer comprised three sublayers identified as Al4Cu9, AlCu, and Al2Cu. Tensile results indicated that increasing the Cu thickness ratio markedly enhanced strength and ductility: the 1 mm composite showed increases of 22.3% in ultimate tensile strength and 70.9% in elongation, while the 2 mm composite exhibited increases of 32.4% and 38.7%, respectively. In contrast, increasing the overall thickness had only a limited effect. Fractography revealed ductile fracture features in both the Al and Cu layers, characterized by more compact interfaces, deeper dimples, and more pronounced tear ridges at higher Cu thickness ratios. These findings demonstrate that optimizing the Cu thickness ratio is an effective strategy for enhancing interfacial bonding strength and overall mechanical performance in Cu/Al/Cu composites.
Open AccessTailoring Interfacial Bonding and Tensile Properties in Cu/Al/Cu Laminated Composites by Adjusting Thickness Ratio
The design of the overall thickness and thickness ratio in multilayered composites is vital because it affects interfacial microstructures and mechanical properties. These elements are significant in the application of multilayered composites in diverse scenarios. This study systematically investigated the interfacial microstructure, mechanical properties, and fracture mechanisms of Cu/Al/Cu trilayered composites with varying overall thicknesses and copper thickness ratios. The microstructure results showed that the distribution and thickness of intermetallic compounds (IMCs) at the Cu/Al interface changed significantly with different thickness designs. As the Cu thickness ratio increased from 20% to 35%, the intermetallic layer transitioned from a continuous structure to a fragmented one in both the 1 mm and 2 mm composites. Additionally, the bonding mechanism evolved from primarily metallurgical bonding to a combination of metallurgical and mechanical bonding. In the 4 mm composite with a 35% Cu thickness ratio, the interfacial intermetallic layer comprised three sublayers identified as Al4Cu9, AlCu, and Al2Cu. Tensile results indicated that increasing the Cu thickness ratio markedly enhanced strength and ductility: the 1 mm composite showed increases of 22.3% in ultimate tensile strength and 70.9% in elongation, while the 2 mm composite exhibited increases of 32.4% and 38.7%, respectively. In contrast, increasing the overall thickness had only a limited effect. Fractography revealed ductile fracture features in both the Al and Cu layers, characterized by more compact interfaces, deeper dimples, and more pronounced tear ridges at higher Cu thickness ratios. These findings demonstrate that optimizing the Cu thickness ratio is an effective strategy for enhancing interfacial bonding strength and overall mechanical performance in Cu/Al/Cu composites.
- Open Access
Tailored Annealing for Interfacial Design and Mechanical Optimization of Cu18150/Al1060/Cu18150 Trilayer Composites
Copper–aluminum layered composites offer a promising combination of high conductivity, light weight, and cost-effectiveness, making them attractive for applications in electric vehicles, electronics, and power transmission. However, achieving reliable interfacial bonding while avoiding excessive work hardening and brittle intermetallic formation remains a significant challenge. In this study, a Cu18150/Al1060/Cu18150 trilayer composite was fabricated through a three-stage high-temperature oxygen-free rolling process. Subsequently, the produced composite was subjected to annealing treatments to systematically investigate the effects of rolling passes, annealing temperature/time on interfacial evolution and mechanical behavior. Results indicate that rolling passes primarily influence interfacial topography and defect distribution. Fewer passes lead to wavy, mechanically bonded interfaces, while more passes improve flatness but reduce intermetallic continuity. Annealing temperature critically governs diffusion kinetics; temperatures up to 400 °C promote the formation of a uniform Al2Cu layer, whereas 450 °C accelerates the growth of brittle Al4Cu9, thickening the intermetallic layer to 18 μm and compromising toughness. Annealing duration further modulates diffusion mechanisms, with short-term (0.5 h) treatments favoring defect-assisted diffusion, resulting in a porous, rapidly thickened layer. In contrast, longer annealing (≥1 h) shifts toward lattice diffusion, which densifies the interface but risks excessive brittle phase formation if prolonged. Mechanical performance evolves accordingly; as-rolled strength increases with the number of rolling passes, but at the expense of ductility. Annealing transforms bonding from a mechanical to a metallurgical condition, shifting fracture from delamination to collaborative failure. The identified optimal process, single-pass rolling followed by annealing at 420 °C for 1 h, yields a balanced interfacial structure of Al2Cu, AlCu, and Al4Cu9 phases, achieving a tensile strength of 258.9 MPa and an elongation of 28.2%, thereby satisfying the target performance criteria (≥220 MPa and ≥20%).
Open AccessTailored Annealing for Interfacial Design and Mechanical Optimization of Cu18150/Al1060/Cu18150 Trilayer Composites
Copper–aluminum layered composites offer a promising combination of high conductivity, light weight, and cost-effectiveness, making them attractive for applications in electric vehicles, electronics, and power transmission. However, achieving reliable interfacial bonding while avoiding excessive work hardening and brittle intermetallic formation remains a significant challenge. In this study, a Cu18150/Al1060/Cu18150 trilayer composite was fabricated through a three-stage high-temperature oxygen-free rolling process. Subsequently, the produced composite was subjected to annealing treatments to systematically investigate the effects of rolling passes, annealing temperature/time on interfacial evolution and mechanical behavior. Results indicate that rolling passes primarily influence interfacial topography and defect distribution. Fewer passes lead to wavy, mechanically bonded interfaces, while more passes improve flatness but reduce intermetallic continuity. Annealing temperature critically governs diffusion kinetics; temperatures up to 400 °C promote the formation of a uniform Al2Cu layer, whereas 450 °C accelerates the growth of brittle Al4Cu9, thickening the intermetallic layer to 18 μm and compromising toughness. Annealing duration further modulates diffusion mechanisms, with short-term (0.5 h) treatments favoring defect-assisted diffusion, resulting in a porous, rapidly thickened layer. In contrast, longer annealing (≥1 h) shifts toward lattice diffusion, which densifies the interface but risks excessive brittle phase formation if prolonged. Mechanical performance evolves accordingly; as-rolled strength increases with the number of rolling passes, but at the expense of ductility. Annealing transforms bonding from a mechanical to a metallurgical condition, shifting fracture from delamination to collaborative failure. The identified optimal process, single-pass rolling followed by annealing at 420 °C for 1 h, yields a balanced interfacial structure of Al2Cu, AlCu, and Al4Cu9 phases, achieving a tensile strength of 258.9 MPa and an elongation of 28.2%, thereby satisfying the target performance criteria (≥220 MPa and ≥20%).
- Open Access
- 2 January 2026
- Published by MDPI AG in Preprints.org
Interfacial Design and Mechanical Optimization of Cu18150/Al1060/Cu18150 Trilayer Metallic Composites via Tailored Annealing after High-Temperature Oxygen-Free Rolling
Copper-aluminum layered composites offer a promising combination of high conductivity, light weight, and cost-effectiveness, making them attractive for applications in electric vehicles, electronics, and power transmission. However, achieving reliable interfacial bonding while avoiding excessive work hardening and brittle intermetallic formation remains a significant challenge. In this study, a Cu18150/Al1060/Cu18150 trilayer composite was fabricated through a three-stage high-temperature oxygen-free rolling process. Subsequently, the produced composite was subjected to annealing treatments to systematically investigate the effects of rolling passes, annealing temperature/time on interfacial evolution and mechanical behavior. Results indicate that rolling passes primarily influence interfacial topography and defect distribution. Fewer passes lead to wavy, mechanically bonded interfaces, while more passes improve flatness but reduce intermetallic continuity. Annealing temperature critically governs diffusion kinetics; temperatures up to 400 °C promote the formation of a uniform Al2Cu layer, whereas 450 °C accelerates the growth of brittle Al4Cu9, thickening the intermetallic layer to 18 μm and compromising toughness. Annealing duration further modulates diffusion mechanisms, with short-term (0.5 h) treatments favoring defect-assisted diffusion, resulting in a porous, rapidly thickened layer. In contrast, longer annealing (≥1 h) shifts toward lattice diffusion, which densifies the interface but risks excessive brittle phase formation if prolonged. Mechanical performance evolves accordingly; as-rolled strength increases with the number of rolling passes, but at the expense of ductility. Annealing transforms bonding from a mechanical to a metallurgical condition, shifting fracture from delamination to collaborative failure. The identified optimal process, single-pass rolling followed by annealing at 420°C for 1 hour, yields a balanced interfacial structure of Al2Cu, AlCu, and Al4Cu9 phases, achieving a tensile strength of 258.9 MPa and an elongation of 28.2%, thereby satisfying the target performance criteria (≥220 MPa and ≥20%).
- 2 January 2026
- Published by MDPI AG in Preprints.org
Open AccessInterfacial Design and Mechanical Optimization of Cu18150/Al1060/Cu18150 Trilayer Metallic Composites via Tailored Annealing after High-Temperature Oxygen-Free Rolling
Copper-aluminum layered composites offer a promising combination of high conductivity, light weight, and cost-effectiveness, making them attractive for applications in electric vehicles, electronics, and power transmission. However, achieving reliable interfacial bonding while avoiding excessive work hardening and brittle intermetallic formation remains a significant challenge. In this study, a Cu18150/Al1060/Cu18150 trilayer composite was fabricated through a three-stage high-temperature oxygen-free rolling process. Subsequently, the produced composite was subjected to annealing treatments to systematically investigate the effects of rolling passes, annealing temperature/time on interfacial evolution and mechanical behavior. Results indicate that rolling passes primarily influence interfacial topography and defect distribution. Fewer passes lead to wavy, mechanically bonded interfaces, while more passes improve flatness but reduce intermetallic continuity. Annealing temperature critically governs diffusion kinetics; temperatures up to 400 °C promote the formation of a uniform Al2Cu layer, whereas 450 °C accelerates the growth of brittle Al4Cu9, thickening the intermetallic layer to 18 μm and compromising toughness. Annealing duration further modulates diffusion mechanisms, with short-term (0.5 h) treatments favoring defect-assisted diffusion, resulting in a porous, rapidly thickened layer. In contrast, longer annealing (≥1 h) shifts toward lattice diffusion, which densifies the interface but risks excessive brittle phase formation if prolonged. Mechanical performance evolves accordingly; as-rolled strength increases with the number of rolling passes, but at the expense of ductility. Annealing transforms bonding from a mechanical to a metallurgical condition, shifting fracture from delamination to collaborative failure. The identified optimal process, single-pass rolling followed by annealing at 420°C for 1 hour, yields a balanced interfacial structure of Al2Cu, AlCu, and Al4Cu9 phases, achieving a tensile strength of 258.9 MPa and an elongation of 28.2%, thereby satisfying the target performance criteria (≥220 MPa and ≥20%).
- Open Access
Layer Thickness Effects on Residual Stress, Microstructure, and Tensile Properties of Cu18150/Al1060/Cu18150 Multilayered Composites: An Integrated EBSD-KAM Approach
This study examines the influence of layer thickness (0.9, 1.6, 2.4, and 4 mm) on the distribution of residual stress, microstructural evolution, and tensile properties of Cu18150/Al1060/Cu18150 multilayered composites fabricated via a combined cast-rolling and hot-rolling technique. The grain refinement, dislocation density, and residual stress gradients across the interfaces were characterized and analyzed using integrated electron backscatter diffraction and kernel average misorientation mapping. The results demonstrated that specimens with a lower layer thickness (0.9–1.6 mm) possess a significantly improved tensile strength of 351 MPa, which is mainly due to the significant grain refinement and the presence of compressive residual stresses at the region of the Al/Cu interfaces. However, tensile strength decreased to 261 MPa in specimens with thicker layers (4 mm), accompanied by improved ductility, e.g., elongation of 30%. This is associated with a reduction in the degrees of interfacial constraint and the formation of more homogeneous deformation structures that accommodate a larger strain. The intermediate layer thickness of 2.4 mm offers an optimal compromise, achieving a tensile strength of 317 MPa while maintaining balanced mechanical performance. These results emphasize the importance of layer thickness in controlling such stress profiles and optimizing the mechanical behavior of hybrid metal composites, providing useful guidance on the design and fabrication of superior structural-form materials.
Open AccessLayer Thickness Effects on Residual Stress, Microstructure, and Tensile Properties of Cu18150/Al1060/Cu18150 Multilayered Composites: An Integrated EBSD-KAM Approach
This study examines the influence of layer thickness (0.9, 1.6, 2.4, and 4 mm) on the distribution of residual stress, microstructural evolution, and tensile properties of Cu18150/Al1060/Cu18150 multilayered composites fabricated via a combined cast-rolling and hot-rolling technique. The grain refinement, dislocation density, and residual stress gradients across the interfaces were characterized and analyzed using integrated electron backscatter diffraction and kernel average misorientation mapping. The results demonstrated that specimens with a lower layer thickness (0.9–1.6 mm) possess a significantly improved tensile strength of 351 MPa, which is mainly due to the significant grain refinement and the presence of compressive residual stresses at the region of the Al/Cu interfaces. However, tensile strength decreased to 261 MPa in specimens with thicker layers (4 mm), accompanied by improved ductility, e.g., elongation of 30%. This is associated with a reduction in the degrees of interfacial constraint and the formation of more homogeneous deformation structures that accommodate a larger strain. The intermediate layer thickness of 2.4 mm offers an optimal compromise, achieving a tensile strength of 317 MPa while maintaining balanced mechanical performance. These results emphasize the importance of layer thickness in controlling such stress profiles and optimizing the mechanical behavior of hybrid metal composites, providing useful guidance on the design and fabrication of superior structural-form materials.
- Open Access
Interfacial Shear Fracture Behavior of C18150Cu/1060Al/C18150Cu Trilayered Composite at Different Temperatures
Interfacial shear fracture behavior of C18150Cu/1060Al/C18150Cu trilayered composite at different temperatures, which was fabricated by high-temperature oxygen-free hot rolling technology. The interfacial microstructure, interfacial shear strength, interfacial shear fracture morphology, and microstructure near the shear fracture were systematically investigated. The results reveal that the composite exhibits a metallurgical and mechanical bonding interface, along with mechanical interlocking between the copper and aluminum. As the testing temperature increases, the interfacial shear strength decreases. At temperatures below 150 °C, the strength remains stable, but it sharply decreases at temperatures above 150 °C. Specifically, the interfacial shear strength is 56.8 MPa at room temperature and 20.9 MPa at 350 °C. When the testing temperature is below 100 °C, the interfacial shear fracture predominantly occurs at the interface between the copper alloy and intermetallics. Also, aluminum is attached to the copper surface of the shear fracture, and the size and quantity of attached aluminum increase with the increase in temperature. When the testing temperature exceeds 100 °C, curled aluminum appears on the copper layer, and a large number of intermetallics are attached to the aluminum surface. This indicates that the bonding strength between intermetallics and aluminum is higher than that between intermetallics and copper.
Open AccessInterfacial Shear Fracture Behavior of C18150Cu/1060Al/C18150Cu Trilayered Composite at Different Temperatures
Interfacial shear fracture behavior of C18150Cu/1060Al/C18150Cu trilayered composite at different temperatures, which was fabricated by high-temperature oxygen-free hot rolling technology. The interfacial microstructure, interfacial shear strength, interfacial shear fracture morphology, and microstructure near the shear fracture were systematically investigated. The results reveal that the composite exhibits a metallurgical and mechanical bonding interface, along with mechanical interlocking between the copper and aluminum. As the testing temperature increases, the interfacial shear strength decreases. At temperatures below 150 °C, the strength remains stable, but it sharply decreases at temperatures above 150 °C. Specifically, the interfacial shear strength is 56.8 MPa at room temperature and 20.9 MPa at 350 °C. When the testing temperature is below 100 °C, the interfacial shear fracture predominantly occurs at the interface between the copper alloy and intermetallics. Also, aluminum is attached to the copper surface of the shear fracture, and the size and quantity of attached aluminum increase with the increase in temperature. When the testing temperature exceeds 100 °C, curled aluminum appears on the copper layer, and a large number of intermetallics are attached to the aluminum surface. This indicates that the bonding strength between intermetallics and aluminum is higher than that between intermetallics and copper.
- Open Access
Corrosion Behavior of Homogenized and Extruded 1100 Aluminum Alloy in Acidic Salt Spray
The 1100 aluminum alloy has been widely used in many industrial fields due to its high specific strength, fracture toughness, excellent thermal conductivity, and corrosion resistance. In this study, the corrosion behavior of the homogenized and hot-extruded 1100 aluminum alloy in acid salt spray environment for different time was studied. The microstructure of the 1100 aluminum alloy before and after corrosion was characterized by an optical microscope (OM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and a laser scanning confocal microscope (LSCM). The difference in corrosion resistance between the homogenized and extruded 1100 aluminum alloy was analyzed via the electrochemical method. The results indicate that after hot extrusion at 400 °C, the microstructure of the 1100 aluminum alloy changes from an equiaxed crystal structure with (111) preferentially distributed in a fibrous structure with (220) preferentially distributed. There was no obvious dynamic recrystallization occurring during extrusion, and the second-phase particles containing Al-Fe-Si were coarse and unevenly distributed. With the increase in corrosion time, corrosion pits appeared on the surface of the 1100 aluminum alloy, and a corrosion product layer was formed on the surface of the homogenized 1100 aluminum alloy, which reduced the corrosion rate. After 96 h of corrosion, the CPR of the extruded samples was 0.619 mm/a, and that of the homogenized samples was 0.442 mm/a. The corrosion resistance of the extruded 1100 aluminum alloy was affected by the microstructure and the second phase, and no protective layer of corrosion products was formed on the surface, resulting in a faster corrosion rate and deeper corrosion pits.
Open AccessCorrosion Behavior of Homogenized and Extruded 1100 Aluminum Alloy in Acidic Salt Spray
The 1100 aluminum alloy has been widely used in many industrial fields due to its high specific strength, fracture toughness, excellent thermal conductivity, and corrosion resistance. In this study, the corrosion behavior of the homogenized and hot-extruded 1100 aluminum alloy in acid salt spray environment for different time was studied. The microstructure of the 1100 aluminum alloy before and after corrosion was characterized by an optical microscope (OM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and a laser scanning confocal microscope (LSCM). The difference in corrosion resistance between the homogenized and extruded 1100 aluminum alloy was analyzed via the electrochemical method. The results indicate that after hot extrusion at 400 °C, the microstructure of the 1100 aluminum alloy changes from an equiaxed crystal structure with (111) preferentially distributed in a fibrous structure with (220) preferentially distributed. There was no obvious dynamic recrystallization occurring during extrusion, and the second-phase particles containing Al-Fe-Si were coarse and unevenly distributed. With the increase in corrosion time, corrosion pits appeared on the surface of the 1100 aluminum alloy, and a corrosion product layer was formed on the surface of the homogenized 1100 aluminum alloy, which reduced the corrosion rate. After 96 h of corrosion, the CPR of the extruded samples was 0.619 mm/a, and that of the homogenized samples was 0.442 mm/a. The corrosion resistance of the extruded 1100 aluminum alloy was affected by the microstructure and the second phase, and no protective layer of corrosion products was formed on the surface, resulting in a faster corrosion rate and deeper corrosion pits.
- Open Access
Investigation on the Corrosion Resistance of 3003 Aluminum Alloy in Acidic Salt Spray under Different Processing States
3003 aluminum alloy exhibits commendable corrosion resistance, ease of processing, and good formability, rendering it extensively utilized across many industrial sectors. In this study, the corrosion behavior of 3003 aluminum alloy in a homogenized state and after hot extrusion deformation in an acidic salt spray environment for different times was studied. The microstructure of the 3003 aluminum alloy in the homogenized state and after hot extrusion was characterized using scanning electron microscopy (SEM), optical microscope (OM), laser scanning confocal microscope (LSCM) etc., while electrochemical methods were employed to study the difference in corrosion resistance between these two states. The results show that corrosion pits on the surface of the homogenized 3003 aluminum alloy increase with time, and corrosion extends along the second phase arrangement, while the hot extruded 3003 aluminum alloy mainly exhibits corrosion pit extension. The grain size of the homogenized 3003 aluminum alloy is larger than that of the hot extruded state, and the second phase is distributed in a reticular pattern. Hot extrusion deformation ensures not only a uniform distribution of the second phase in the 3003 aluminum alloy but also a reduced grain size, an increased grain boundary density, a heightened electrochemical activity in acidic environments, and an augmented pitting density. Compared with the homogenized 3003 aluminum alloy, the pitting density, maximum pitting depth, and weight loss of the hot extruded state are increased.
Open AccessInvestigation on the Corrosion Resistance of 3003 Aluminum Alloy in Acidic Salt Spray under Different Processing States
3003 aluminum alloy exhibits commendable corrosion resistance, ease of processing, and good formability, rendering it extensively utilized across many industrial sectors. In this study, the corrosion behavior of 3003 aluminum alloy in a homogenized state and after hot extrusion deformation in an acidic salt spray environment for different times was studied. The microstructure of the 3003 aluminum alloy in the homogenized state and after hot extrusion was characterized using scanning electron microscopy (SEM), optical microscope (OM), laser scanning confocal microscope (LSCM) etc., while electrochemical methods were employed to study the difference in corrosion resistance between these two states. The results show that corrosion pits on the surface of the homogenized 3003 aluminum alloy increase with time, and corrosion extends along the second phase arrangement, while the hot extruded 3003 aluminum alloy mainly exhibits corrosion pit extension. The grain size of the homogenized 3003 aluminum alloy is larger than that of the hot extruded state, and the second phase is distributed in a reticular pattern. Hot extrusion deformation ensures not only a uniform distribution of the second phase in the 3003 aluminum alloy but also a reduced grain size, an increased grain boundary density, a heightened electrochemical activity in acidic environments, and an augmented pitting density. Compared with the homogenized 3003 aluminum alloy, the pitting density, maximum pitting depth, and weight loss of the hot extruded state are increased.