Deokhyun Han
Research Subjects
Deokhyun Han has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Byungmin Ahn
Department of Materials Science and Engineering, Ajou University, Suwon, Republic of Korea
3 shared publications - Dae-Weon Kim
Advanced Materials and Processing Center Institute for Advanced Engineering ( IAE) 17180 Yongin Korea
1 shared publication - Donhee Lee
Department of Material Science and Engineering Korea Aerospace University 10540 Goyang Republic of Korea
1 shared publication - Du Hong Kang
Department of Material Science and Engineering Korea Aerospace University 10540 Goyang Republic of Korea
1 shared publication Geon-Hong Kim
1 shared publication- Hang-Chul Jung
Institute for Advanced Engineering (IAE), Yongin, Korea
1 shared publication
Latest Publications
- Open Access
- 31 August 2026
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 33 (4) , 291-298
Effect of Milling-Time-Dependent Zirconia Contamination on the Microstructure and Mechanical Properties of Mechanically Alloyed Multicomponent Nb-Si-Ti Sintered Alloys
Multicomponent Nb-15Si-23Ti-3Cr-2Sn-2Al-2Hf-1B-0.5Y alloy powders were synthesized by high-energy ball milling using a zirconia chamber and balls for milling times of 0.5–12 h, and the effects of milling time on powder evolution, contamination behavior, and the resulting microstructure and mechanical properties of hot-pressed sintered specimens were systematically investigated. The dominant deformation mechanism shifted from flattening to cold welding and then to a fracture-dominated steady state with increasing milling time, and the particle size decreased sharply up to 4 h before stabilizing. Yield and composition analyses showed that zirconia contamination remained limited up to 4 h but increased sharply beyond 6 h owing to severe wear of the milling chamber and balls. Sintered specimens from powder milled for 4 h exhibited a homogeneous microstructure with finely and stably dispersed Nb5Si3 intermetallic phases and moderate hardness, whereas insufficient milling for 2 h left coarse, unreacted phases, and excessive milling for 12 h introduced substantial zirconia contamination that lowered density while raising hardness. These results indicate that a milling time in the range of 4–6 h offers a favorable balance between alloying efficiency and contamination control among the conditions examined, with 4 h being preferred owing to its comparatively minimal zirconia contamination, for multicomponent Nb-Si-Ti alloy powders processed with zirconia milling media.
- 31 August 2026
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 33 (4) , 291-298
Open AccessEffect of Milling-Time-Dependent Zirconia Contamination on the Microstructure and Mechanical Properties of Mechanically Alloyed Multicomponent Nb-Si-Ti Sintered Alloys
Multicomponent Nb-15Si-23Ti-3Cr-2Sn-2Al-2Hf-1B-0.5Y alloy powders were synthesized by high-energy ball milling using a zirconia chamber and balls for milling times of 0.5–12 h, and the effects of milling time on powder evolution, contamination behavior, and the resulting microstructure and mechanical properties of hot-pressed sintered specimens were systematically investigated. The dominant deformation mechanism shifted from flattening to cold welding and then to a fracture-dominated steady state with increasing milling time, and the particle size decreased sharply up to 4 h before stabilizing. Yield and composition analyses showed that zirconia contamination remained limited up to 4 h but increased sharply beyond 6 h owing to severe wear of the milling chamber and balls. Sintered specimens from powder milled for 4 h exhibited a homogeneous microstructure with finely and stably dispersed Nb5Si3 intermetallic phases and moderate hardness, whereas insufficient milling for 2 h left coarse, unreacted phases, and excessive milling for 12 h introduced substantial zirconia contamination that lowered density while raising hardness. These results indicate that a milling time in the range of 4–6 h offers a favorable balance between alloying efficiency and contamination control among the conditions examined, with 4 h being preferred owing to its comparatively minimal zirconia contamination, for multicomponent Nb-Si-Ti alloy powders processed with zirconia milling media.
- Open Access
- 27 October 2025
- Published by The Materials Research Society of Korea in Korean Journal of Materials Research
- Vol. 35 (10) , 473-478
Effect of Cl2 Gas Exposure on the Surface Properties of Electropolished STS316L
In this study, the surface characteristics-including roughness, oxide layer thickness, and composition-of the electropolished layer on STS316L steel tubes subjected to double melting via the VIM/VAR process were investigated after exposure to Cl 2 gas. The tubes were exposed to Cl 2 gas for 1 to 13 d to simulate semiconductor conditions. Surface roughness increased with Cl 2 exposure time, showing values of 0.01, 0.04, 0.04 and 0.03 µm after 0, 1, 5 and 9 d, respectively. At the same time, the oxide layer thickness on EPed STS316L, which was initially 8.2 nm, decreased to 3.18, 2.58 after 1, 5 d of Cl 2 exposure, approaching the initial thickness of 2.38 nm observed on non-EPed STS316L. After 9 d, the thickness further decreased to 0.51 nm, with no significant change was observed thereafter. Before Cl 2 exposure, the CrO/FeO ratio was 2.26. After 1, 5, and 9 d of exposure, the ratio decreased to 2.06, 1.75, and 1.27, respectively. In addition, the penetration depth of Cl into the oxide layer increased with longer exposure time. These results suggest that the formation of chromium chlorides led to the breakdown of the stable Cr 2 O 3 layer.
- 27 October 2025
- Published by The Materials Research Society of Korea in Korean Journal of Materials Research
- Vol. 35 (10) , 473-478
Open AccessEffect of Cl2 Gas Exposure on the Surface Properties of Electropolished STS316L
In this study, the surface characteristics-including roughness, oxide layer thickness, and composition-of the electropolished layer on STS316L steel tubes subjected to double melting via the VIM/VAR process were investigated after exposure to Cl 2 gas. The tubes were exposed to Cl 2 gas for 1 to 13 d to simulate semiconductor conditions. Surface roughness increased with Cl 2 exposure time, showing values of 0.01, 0.04, 0.04 and 0.03 µm after 0, 1, 5 and 9 d, respectively. At the same time, the oxide layer thickness on EPed STS316L, which was initially 8.2 nm, decreased to 3.18, 2.58 after 1, 5 d of Cl 2 exposure, approaching the initial thickness of 2.38 nm observed on non-EPed STS316L. After 9 d, the thickness further decreased to 0.51 nm, with no significant change was observed thereafter. Before Cl 2 exposure, the CrO/FeO ratio was 2.26. After 1, 5, and 9 d of exposure, the ratio decreased to 2.06, 1.75, and 1.27, respectively. In addition, the penetration depth of Cl into the oxide layer increased with longer exposure time. These results suggest that the formation of chromium chlorides led to the breakdown of the stable Cr 2 O 3 layer.
- 28 December 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (4) , 987-990
Synthesis of the Nickel-Cobalt-Manganese Cathode Material Using Recycled Nickel as Precursors from Secondary Batteries
As the amount of high-capacity secondary battery waste gradually increased, waste secondary batteries for industry (high-speed train & HEV) were recycled and materialization studies were carried out. The precipitation experiment was carried out with various conditions in the synthesis of LiNi0.6Co0.2Mn0.2O2 material using a Taylor reactor. The raw material used in this study was a leaching solution generated from waste nickel-based batteries. The nickel-cobalt-manganese (NCM) precursor was prepared by the Taylor reaction process. Material analysis indicated that spherical powder was formed, and the particle size of the precursor was decreased as the reaction speed was increased during the preparation of the NCM. The spherical NCM powder having a particle size of 10 µm was synthesized using reaction conditions, stirring speed of 1000 rpm for 24 hours. The NCM precursor prepared by the Taylor reaction was synthesized as a cathode material for the LIB, and then a coin-cell was manufactured to perform the capacity evaluation.
- 28 December 2021
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 66 (4) , 987-990
Synthesis of the Nickel-Cobalt-Manganese Cathode Material Using Recycled Nickel as Precursors from Secondary Batteries
As the amount of high-capacity secondary battery waste gradually increased, waste secondary batteries for industry (high-speed train & HEV) were recycled and materialization studies were carried out. The precipitation experiment was carried out with various conditions in the synthesis of LiNi0.6Co0.2Mn0.2O2 material using a Taylor reactor. The raw material used in this study was a leaching solution generated from waste nickel-based batteries. The nickel-cobalt-manganese (NCM) precursor was prepared by the Taylor reaction process. Material analysis indicated that spherical powder was formed, and the particle size of the precursor was decreased as the reaction speed was increased during the preparation of the NCM. The spherical NCM powder having a particle size of 10 µm was synthesized using reaction conditions, stirring speed of 1000 rpm for 24 hours. The NCM precursor prepared by the Taylor reaction was synthesized as a cathode material for the LIB, and then a coin-cell was manufactured to perform the capacity evaluation.
- 8 July 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 65 (3) , 1019-1022
Effect of Al/Cu Weight Fraction on the Mechanical and Electrical Properties of Al-Cu Conductors for Overhead Transmission Lines
In the past few years, overhead copper transmission lines have been replaced by lightweight aluminum transmission lines to minimize the cost and prevent the sagging of heavier copper transmission lines. High strength aluminum alloys are used as the core of the overhead transmission lines because of the low strength of the conductor line. However, alloying copper with aluminum causes a reduction in electrical conductivity due to the solid solution of each component. Therefore, in this study, the authors attempt to study the effect of various Al/Cu ratios (9:1, 7:3, 5:5) to obtain a high strength Al-Cu alloy without a significant loss in its conductivity through powder metallurgy. Low-temperature extrusion of Al/Cu powder was done at 350ºC to minimize the alloying reactions. The as-extruded microstructure was analyzed and various phases (Cu9Al4, CuAl2) were determined. The tensile strength and electrical conductivity of different mixing ratios of Al and Cu powders were studied. The results suggest that the tensile strength of samples is improved considerably while the conductivity falls slightly but lies within the limits of applications.
- 8 July 2020
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 65 (3) , 1019-1022
Effect of Al/Cu Weight Fraction on the Mechanical and Electrical Properties of Al-Cu Conductors for Overhead Transmission Lines
In the past few years, overhead copper transmission lines have been replaced by lightweight aluminum transmission lines to minimize the cost and prevent the sagging of heavier copper transmission lines. High strength aluminum alloys are used as the core of the overhead transmission lines because of the low strength of the conductor line. However, alloying copper with aluminum causes a reduction in electrical conductivity due to the solid solution of each component. Therefore, in this study, the authors attempt to study the effect of various Al/Cu ratios (9:1, 7:3, 5:5) to obtain a high strength Al-Cu alloy without a significant loss in its conductivity through powder metallurgy. Low-temperature extrusion of Al/Cu powder was done at 350ºC to minimize the alloying reactions. The as-extruded microstructure was analyzed and various phases (Cu9Al4, CuAl2) were determined. The tensile strength and electrical conductivity of different mixing ratios of Al and Cu powders were studied. The results suggest that the tensile strength of samples is improved considerably while the conductivity falls slightly but lies within the limits of applications.