LIL. C. Ingesson

L. C. Ingesson

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


L. C. Ingesson has a total of 62 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effects of neutral gas pressure on calibration parameters of resistive bolometer sensors in fusion devices

    by H. Meister, S. Jahanbakhsh, D. Zhang, L.C. Ingesson, A. Pataki

    Ambient pressure may influence the thermal path between the absorber and heat sink of resistive bolometers and thus impact the calibration parameters. This effect is investigated for metal resistive bolometer sensors as used in bolometer diagnostics on fusion experiments. Measurements in the test facility IBOVAC indicate that pressure has no effect up to 10−3 mbar. However, a significant change in the cooling time constant is observed for pressures above 10−2 mbar, a reduction up to a factor of three at 1 mbar. The measurements performed in N2 and He atmospheres and simulations in H2 indicate no difference between the results from different gas species up to 10−3 mbar and less than 10 % up to 0.1 mbar. A model based on the thermal conductivity of the surrounding gas combined with the geometry of the sensor holder successfully demonstrates that the additional cooling path through the gas, which may vary between the measurement and reference absorbers, can explain the measurement results. Applying the model to the geometry of a sensor holder designed for port-mounted bolometer cameras in ITER led to design modifications that should help reduce the impact of high environmental pressures on the bolometer measurements. Similarly, it can be assumed that applying the model to the geometries and sensors of operating bolometer diagnostics can help correct the measurements and improve the understanding of plasma radiation in the case of high pressures at the location of bolometer sensors.


  • Open Access

    Optimizing ITER Bolometer Cameras in View of Internal Reflections and Crosstalk Between Channels

    by H. Meister, I. Kudashev, M. Brank, L. C. Ingesson

    Bolometer cameras in ITER (lat.: the way) are designed as pinhole and collimator cameras, optimizing the requirements from available physical space, constraints in design options and desired line-of-sight (LOS) distribution. While for both camera types of internal reflections can be significant and lead to an increase in the effective viewing cone, collimator cameras may also suffer from crosstalk of light between channels in case internal apertures are not optimized. The concepts and simulations employed to optimize bolometer collimator cameras are presented. They are based on geometrical considerations for choosing the number and distribution of internal apertures, using the desired viewing cones as input. In the second step, ray-tracing simulations based on the Raysect packages are applied to assess internal reflections as a function of wavelength in the range IR to X-rays for the chosen geometry as well as to assess the impact of choices for material and material finishings (e.g., roughness). Examples presented focus on port-mounted bolometer cameras. The results allow us to improve the geometrical description of bolometer cameras in the ITER database of synthetic diagnostics and thus support performance assessments and studies in the preparation of tomographic reconstructions of plasma radiation. For example, the calculated measurements for LOS assuming standard radiation distributions for ITER are presented.


  • Generic approach to assess the measuring performance of total-radiated power quantities by multi-channel resistive bolometer diagnostics on fusion experiments

    by L. C. Ingesson, A. Doblas, A. Gandhi, S. Jahanbakhsh, H. Meister

    On present-day magnetic-confinement fusion experiments, the performance of multi-channel bolometer diagnostics has typically evolved over time through experience with earlier versions of the diagnostic and experimental results obtained. For future large-scale fusion experiments and reactors, it is necessary to be able to predict the performance as a function of design decisions and constraints. A methodology has been developed to predict the accuracy with which the volume-integrated total radiated power can be estimated from the measurements by a resistive bolometer diagnostic, considering, in particular, its line-of-sight geometry, étendues of individual lines of sight, bolometer-sensor characteristics, and the expected noise level that can be obtained with its electronics and signal chain. The methodology depends on a number of assumptions in order to arrive at analytical expressions but does not restrict the final implementation of data-processing of the diagnostic measurements. The methodology allows us to predict the performance in terms of accuracy, total-radiated power level, and frequency or time resolution and to optimize bolometer-sensor characteristics for a set of performance requirements. This is illustrated for the bolometer diagnostic that is being designed for the ITER experiment. The reasonableness, consequences, and limitations of the assumptions are discussed in detail.


  • Open Access

    Final design of the ITER bolometer first plasma component: cable installation template

    by F. Penzel, A. Pataki, H. Meister, L.C. Ingesson, U. Walach, M.A. Villarejo, A. Gandhi, E. Fresquet, M. Majewski, R. Reichle, et al.

    The ITER bolometer cable installation template is a first plasma component which main function is to provide a temporary fixation of the mineral insulated cables and to protect them through first plasma operation inside the vacuum vessel until the final bolometer cameras are installed in the second assembly phase. In this paper, the final design of the cable installation template will be presented, the assembly procedures and important functional design details in order to be compliant with its interfaces, the vacuum vessel, the flux loops, the electrical services, the first plasma components and the assembly. Requirements that drive the design will be explained, along with the technical solutions chosen to fulfill them. Important sub-components will be presented in more detail, such as the boss fixation, which will compensate geometrical uncertainties of the as-built boss positioning, as well as the mineral insulated cable holder, which will prepare the electrical termination and facilitate the installation of final vacuum vessel cameras during the second assembly phase of ITER. Additionally, the step-by-step assembly plan agreed with the team of ITER machine assembly and tooling will be described. A custom developed boss welding tool will be described as well. The system load specifications applicable for this first plasma component will be presented as well and an overview of the structural integrity analysis report will be given. It will be shown that most loads on the component are very limited and there is no risk of structural failure or loss of relevant system functions. The paper concludes with a summary of the work and an overview of the procurement and delivery status to ITER.


  • Open Access

    Flexible vacuum vessel bolometer camera design in ITER to adapt to the final position of the gaps between Blanket Modules

    by A. Pataki, D. Hermann, L.C. Ingesson, H. Meister, G. Nadasi, F. Penzel, R. Reichle, J. Sanchez, U. Walach


  • Heating, current drive and energetic particle studies on JET in preparation of ITER operation

    by J.-M Noterdaeme, R Budny, A Cardinali, C Castaldo, R Cesario, F Crisanti, J Degrassie, D.A D'Ippolito, F Durodi, A Ekedahl, et al.


  • Observation of detachment in the JET MkIIGB divertor using CCD camera tomography

    by K. Itami, P. Coad, W. Fundamenski, C. Ingesson, J. Lingertat, G.F. Matthews, A. Tabasso


  • Characterization of geometrical detection-system properties for two-dimensional tomography

    by L. C. Ingesson, C. F. Maggi, R. Reichle

    Quantities that characterize the three-dimensional geometrical properties of detection systems for two-dimensional tomography are reviewed and compared. It is discussed how the quantities can be calculated and how they can be measured, including a measuring technique that uses a parallel laser beam. In many detection systems the finite detector size and the finite sizes of bounding apertures are not negligible, and these result in instrument functions with finite widths. Line-integral measurements are referred to as ideal measurements, whereas measurements by systems with instrument functions with finite width are nonideal. The quantities discussed make it possible to take into account these finite sizes in several tomography algorithms. If the spacing between adjacent lines of sight is much smaller than the widths of the instrument functions, the ideal measurements can be approximately reconstructed from the nonideal measurements. Such a reconstruction has been applied to bolometer measurements in a high plasma-density discharge in the Joint European Torus tokamak by sweeping the plasma in front of the bolometer detectors. The sweeping creates many extra virtual lines of sight and thus increases the resolution of the measurements close to the X point, where in high-density plasmas a peak in the radiation is found.