Thierry Hubert
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Thierry Hubert has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Amin Khorasani
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
6 shared publications - Bram Vanderborght
Brubotics, Vrije Universiteit Brussel and Imec, Elsene, Belgium
5 shared publications - Muhammad Usman
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
5 shared publications - Tom Verstraten
Robotics and Multibody Mechanics Research Group, Vrije Universiteit Brussel, Brussels, Belgium
5 shared publications - Greet Van de Perre
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
4 shared publications - Raphaël Furnémont
BruBotics, Vrije Universiteit Brussel, Brussels, Belgium
4 shared publications
Latest Publications
- Open Access
- 25 April 2026
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 225
Uncontrolled collision dynamics and the role of dual motor actuators in impact mitigation
- 25 April 2026
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 225
Open AccessUncontrolled collision dynamics and the role of dual motor actuators in impact mitigation
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 145-152
Flexible-Link Velocity-Bounding Proxy Based Sliding Mode Control
This letter proposes a control strategy for flexible link manipulators preserving high tracking accuracy in free motion, while ensuring smooth and safe behavior in scenarios involving physical interaction or large positional errors, based on the VB-PSMC. The scheme is extended to compensate for the manipulator’s flexural dynamics, resulting in a nested control scheme where damping of the induced oscillations is achieved by a model-free proportional strain feedback while gravity induced deflections are counteracted by a feed-forward term based on a quasi-static Euler-Bernoulli beam model. A convergence study on the modified sliding manifold and a stability analysis of the closed-loop system is provided. The performance of the controller was evaluated experimentally and compared against other control strategies such as PSMC and torque limited PD control. The results demonstrate the controller’s accurate end effector tracking in free motion, while achieving compliant behavior during contact, by efficiently handling the link’s inherent flexibility leading up to a 32% reduction in interaction force. In addition, studying the FL-VB-PSMC response after releasing contact demonstrated the smooth and vibration-free recovery even for large position errors.
- 31 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (1) , 145-152
Flexible-Link Velocity-Bounding Proxy Based Sliding Mode Control
This letter proposes a control strategy for flexible link manipulators preserving high tracking accuracy in free motion, while ensuring smooth and safe behavior in scenarios involving physical interaction or large positional errors, based on the VB-PSMC. The scheme is extended to compensate for the manipulator’s flexural dynamics, resulting in a nested control scheme where damping of the induced oscillations is achieved by a model-free proportional strain feedback while gravity induced deflections are counteracted by a feed-forward term based on a quasi-static Euler-Bernoulli beam model. A convergence study on the modified sliding manifold and a stability analysis of the closed-loop system is provided. The performance of the controller was evaluated experimentally and compared against other control strategies such as PSMC and torque limited PD control. The results demonstrate the controller’s accurate end effector tracking in free motion, while achieving compliant behavior during contact, by efficiently handling the link’s inherent flexibility leading up to a 32% reduction in interaction force. In addition, studying the FL-VB-PSMC response after releasing contact demonstrated the smooth and vibration-free recovery even for large position errors.
- Open Access
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 129787-129802
Cobots Designed for Strength, Not Stiffness
Conventional industrial robots are designed to be as stiff as possible to ensure high positioning accuracy. The stiffness of a structure is, however, strongly related to its mass, leading to heavy structures. This paper aims to quantify the potential gain of reducing and eliminating the stiffness constraints, which is of lesser importance for collaborative robots, by investigating the effect of applying different optimization objectives. The resulting optimized designs are quantitatively compared using a set of performance measures and evaluated against the traditional stiffness-designed approach. It was concluded that significant improvements can be made, e.g. the robot’s mass can be reduced up to 74% compared to traditionally stiff-designed robots. The dependency of the payload as well as the structural/actuator mass distribution on the optimized results is investigated and proved to have a significant influence on the potential improvements when allowing reduced structural rigidity. The relationship between structural mass and actuator mass is investigated and compared to commercially available cobots.
- 22 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 129787-129802
Open AccessCobots Designed for Strength, Not Stiffness
Conventional industrial robots are designed to be as stiff as possible to ensure high positioning accuracy. The stiffness of a structure is, however, strongly related to its mass, leading to heavy structures. This paper aims to quantify the potential gain of reducing and eliminating the stiffness constraints, which is of lesser importance for collaborative robots, by investigating the effect of applying different optimization objectives. The resulting optimized designs are quantitatively compared using a set of performance measures and evaluated against the traditional stiffness-designed approach. It was concluded that significant improvements can be made, e.g. the robot’s mass can be reduced up to 74% compared to traditionally stiff-designed robots. The dependency of the payload as well as the structural/actuator mass distribution on the optimized results is investigated and proved to have a significant influence on the potential improvements when allowing reduced structural rigidity. The relationship between structural mass and actuator mass is investigated and compared to commercially available cobots.
- Open Access
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 118547-118564
Vibration Control and Performance Analysis of a 3DOF High-Payload Flexible Link Manipulator
Flexible link manipulators (FLMs) are often praised for their potential advantages in industrial settings, such as being more lightweight, energy-efficient, and allowing higher operation speeds with smaller actuators. Many studies make unrealistic assumptions, like simplistic links, small deflections, low payloads, limited degrees of freedom, and well-defined mode shapes, which limit their real-world applicability. This paper investigates the performance of a flexible link manipulator with three degrees of freedom, designed for high payload capabilities and characterized by complex link shapes and complex vibration modes. An advanced control methodology was developed following the identification of the parameter-varying flexible link manipulator setup to manage the manipulator’s vibrations effectively. Comparative experiments were conducted between the flexible link manipulator and a conventional rigid link manipulator, assessing performance metrics such as repeatability, overshoot, settling time, torque and energy consumption. The results show that the flexible link manipulator, equipped with the advanced control system, achieves a repeatability of 0.14 mm, comparable to that of commercially available rigid robots. Moreover, energy consumption is reduced even with the implementation of active vibration suppression. The study highlights the potential of flexible link manipulators for real-world applications.
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 118547-118564
Open AccessVibration Control and Performance Analysis of a 3DOF High-Payload Flexible Link Manipulator
Flexible link manipulators (FLMs) are often praised for their potential advantages in industrial settings, such as being more lightweight, energy-efficient, and allowing higher operation speeds with smaller actuators. Many studies make unrealistic assumptions, like simplistic links, small deflections, low payloads, limited degrees of freedom, and well-defined mode shapes, which limit their real-world applicability. This paper investigates the performance of a flexible link manipulator with three degrees of freedom, designed for high payload capabilities and characterized by complex link shapes and complex vibration modes. An advanced control methodology was developed following the identification of the parameter-varying flexible link manipulator setup to manage the manipulator’s vibrations effectively. Comparative experiments were conducted between the flexible link manipulator and a conventional rigid link manipulator, assessing performance metrics such as repeatability, overshoot, settling time, torque and energy consumption. The results show that the flexible link manipulator, equipped with the advanced control system, achieves a repeatability of 0.14 mm, comparable to that of commercially available rigid robots. Moreover, energy consumption is reduced even with the implementation of active vibration suppression. The study highlights the potential of flexible link manipulators for real-world applications.
- Open Access
- 2 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (6) , 5982-5989
Mitigating Collision Forces and Improving Response Performance in Human-Robot Interaction by Using Dual-Motor Actuators
In collaborative robotics, the safety of humans interacting with cobots is crucial. There is a need for collaborative robots that can move quickly while still being safe. This letter introduces the use of a kinematically redundant actuator in impedance control mode to reduce collision forces, aiming to improve both the safety and efficiency of collaborative robots. By distributing power across multiple drive-trains, each with unique properties such as reflected inertia, the actuator's behavior during collisions is optimized, which is key for safe interactions. Using theoretical analysis and practical experiments, we evaluate the response performance of the redundant actuator in various collision situations according to ISO/TS 15066, comparing it with that of a standard single-drive actuator. Our experiments show that the redundant actuator significantly lowers collision forces, with a 44% reduction in peak forces and an 81% decrease in transferred impulses during collisions. The letter concludes by offering a design parameter recommendation for designing actuators with reduced reflected inertia.
- 2 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (6) , 5982-5989
Open AccessMitigating Collision Forces and Improving Response Performance in Human-Robot Interaction by Using Dual-Motor Actuators
In collaborative robotics, the safety of humans interacting with cobots is crucial. There is a need for collaborative robots that can move quickly while still being safe. This letter introduces the use of a kinematically redundant actuator in impedance control mode to reduce collision forces, aiming to improve both the safety and efficiency of collaborative robots. By distributing power across multiple drive-trains, each with unique properties such as reflected inertia, the actuator's behavior during collisions is optimized, which is key for safe interactions. Using theoretical analysis and practical experiments, we evaluate the response performance of the redundant actuator in various collision situations according to ISO/TS 15066, comparing it with that of a standard single-drive actuator. Our experiments show that the redundant actuator significantly lowers collision forces, with a 44% reduction in peak forces and an 81% decrease in transferred impulses during collisions. The letter concludes by offering a design parameter recommendation for designing actuators with reduced reflected inertia.
- Open Access
- 11 April 2024
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 197
Modeling of flexible shaft for robotics applications
- 11 April 2024
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 197
Open AccessModeling of flexible shaft for robotics applications
- Open Access
- 8 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (5) , 4790-4797
Flexible Shaft as Remote and Elastic Transmission for Robot Arms
Research on human-friendly robots focuses on safety through software and hardware. Hardware-based safety offers a significant advantage over software-based safety if an accurate hardware model is integrated into the solution. Design of elastic and off-joint actuation has established safety by hardware, where the inherent qualities of elastic and lightweight nature make the robot safe for interaction. Combining series elastic actuators with cable/belt pulley-based remote transmission offers inherently safe hardware design, albeit with increased design and modeling complexity. This letter introduces remote and elastic actuation as a single-element solution for robot arm design using a flexible shaft. The test-bench approach studies the remote and elastic effects of a flexible shaft-based transmission for a robot. A set of nine flexible shafts, differing in length and diameter, are used for benchmarking as 3-D surface empirical maps to facilitate their optimal selection for robot design. An example 3 Degree Of Freedom (DOF) robot arm using a flexible shaft as a remote and elastic actuator is designed and modeled. A low-level control based on a flexible shaft is proposed, backed by the experimental results.
- 8 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 9 (5) , 4790-4797
Open AccessFlexible Shaft as Remote and Elastic Transmission for Robot Arms
Research on human-friendly robots focuses on safety through software and hardware. Hardware-based safety offers a significant advantage over software-based safety if an accurate hardware model is integrated into the solution. Design of elastic and off-joint actuation has established safety by hardware, where the inherent qualities of elastic and lightweight nature make the robot safe for interaction. Combining series elastic actuators with cable/belt pulley-based remote transmission offers inherently safe hardware design, albeit with increased design and modeling complexity. This letter introduces remote and elastic actuation as a single-element solution for robot arm design using a flexible shaft. The test-bench approach studies the remote and elastic effects of a flexible shaft-based transmission for a robot. A set of nine flexible shafts, differing in length and diameter, are used for benchmarking as 3-D surface empirical maps to facilitate their optimal selection for robot design. An example 3 Degree Of Freedom (DOF) robot arm using a flexible shaft as a remote and elastic actuator is designed and modeled. A low-level control based on a flexible shaft is proposed, backed by the experimental results.