JFJana Forkun

Jana Forkun

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jana Forkun has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • DETERMINING THE OPTIMUM POWER OF AN ABSORPTION HEAT PUMP WHEN IT INTEGRATING TO PT-60/70-130/13 THERMAL SCHEME

    by Олександр Леонідович Шубенко, Oleksandr Usatyi, Микола Юрійович Бабак, Yana Forkun, Oleksandr Senetskyi, Яна Борисівна Форкун

    The problem of determining the optimal thermal power of an absorption heat pump with steam heating at one-stage regeneration (COP = 1.71) is solved. The heat pump is integrated into the thermal scheme of PT-60/70-130/13 steam turbine. The heat supply schedule for this steam turbine cycle is 150/70 °С. The installation also produces steam for technological needs. The thermal and flow rate characteristics of an absorption heat pump are determined using the constructed and proposed approximation mathematical model. Based on the analysis and existing experience, an optimization problem was formulated. The goal function is to select the integrated absorption heat optimal power pump with the condition of optimal energy fuel consumption. The search for the optimal thermal power of an absorption heat pump was carried out under the condition of steam release through a controlled production turbine extraction with parameters of 1.296 MPa, 280 °C. Options for variable steam consumption for process needs (0, 20, 50 and 80 t/h) were considered. The condition was constancy of consumption throughout the year. The results obtained showed that, relative to all considered turbine loading modes, the optimal power value of the absorption heat pump is identical and amounts to ~ 17.25 MW. Calculation studies have shown that at a cost of electricity of 0.13 USD/(kWh) and equivalent fuel of 309 USD/t, a power unit with PT-60/70-130/13 turbine and an integrated absorption heat pump (thermal power 15–18 MW) with a production load of more than 20 t/h of steam, as well as a consumption of recycled network water for heat supply of more than ~ 1550 t/h, the payback of the energy saving project will be achieved in less than 3 years. The next positive effect is that fuel savings can reduce CO2 emissions by 9321 tons and NOx by 48 tons. According to research results, we observe a positive environmental effect from the integration of an absorption heat pump into the existing thermal scheme. Вирішується задача визначення оптимальної теплової потужності абсорбційного теплового насоса з паровим нагріванням при одноступеневій регенерації (СОР = 1,71). Розглядуваний тепловий насос інтегрований в теплову схему парової турбіни ПТ-60/70-130/13. Графік теплопостачання для даного паротурбінного циклу становить 150/70 °С. Також установкою виробляється пар на технологічні потреби. Визначення теплових та витратних характеристик абсорбційного теплового насоса здійснюється з використанням побудованої та запропонованої апроксимаційної математичної моделі. На підставі проведеного аналізу та наявного досвіду сформульовано оптимізаційну задачу. Функцією мети є вибір оптимальної потужності інтегрованого абсорбційного теплового насоса за умови оптимальної витрати енергетичного палива. Пошук оптимальної теплової потужності абсорбційного теплового насоса здійснювався за умови відпуску пари через регульований виробничий відбір турбіни з параметрами 1,296 МПа, 280 °С. Були розглянуті варіанти для змінної витрати пари на технологічні потреби (0, 20, 50 та 80 т/год). Умовою була постійність витрати протягом року. Отримані результати показали, що щодо всіх розглянутих режимів завантаження турбіни, оптимальне значення потужності абсорбційного теплового насоса є ідентичним і становить ~ 17,25 МВт. Розрахункові дослідження показали, що за вартості електроенергії 0,13 дол./(кВт·ч) та умовного палива 309 дол./т енергоблок з турбіною ПТ-60/70-130/13 та інтегрований абсорбційний тепловий насос (тепловою потужністю 15–18 МВт) при виробничому навантаженні понад 20 т/год пари, а також витраті оборотної мережної води на теплопостачання понад 1550 т/год дозволить отримати окупність проекту енергозбереження менше 3 років. Наступним позитивним ефектом є те, що економія палива дозволяє знизити викиди СО2 на 9321 т і NOx на 48 т. За результатами досліджень спостерігаємо позитивний екологічний ефект від інтеграції абсорбційного теплового насоса в існуючу теплову схему.


  • Open Access

    INDUCTION WIND GENERATOR USING EXCITATION CAPACITORS

    by Oleksiy Iegorov, Olga Iegorova, Marina Glebova, Jana Forkun

    The development of autonomous energy is characterized by a growing need for autonomous sources of electricity of various capacities, increased requirements for the quality of electrical energy, reliability and efficiency. In this regard, the design and cr

  • Open Access

    FEATURES CALCULATIONS OF DYNAMIC MODES OF THE ELECTRICAL SYSTEM

    by Oleksiy Iegorov, Olga Iegorova, Marina Glebova, Jana Forkun

    The purpose of the study is to consider modeling the modes of local objects on a single information model within the framework of an automated system for controlling the modes of electrical systems. A mathematical model of the electrical system is propose

  • Open Access

    DETERMINATION OF DEVIATIONS OF THE PARAMETERS OF THE MAGNET WIRES OF ELECTRIC MACHINES

    by Oleksiy Iegorov, Olga Iegorova, Marina Glebova, Jana Forkun

    The paper considers the principles and conditions of modeling the cores of electric machines with damage. The feasibility of using the finite element method in the analysis of electromagnetic processes and fields of electric machines is justified and the

  • Open Access

    Dependence of starting characteristics on the shape of rotor slots

    by Oleksiy Iegorov, Marina Glebova, Jana Forkun

    At present, induction motors with a squirrel-cage rotor drive based on them are widely used. The breadth of the field of use of induction electric motors is so great due to the large power range, simple design, reliability and high technical and economic indicators, the possibility of producing these machines with various degrees of protection, which allows them to be used both under normal operating conditions and under harsh environmental conditions. The review of technical literature was carried out and various forms of stator and rotor slots were considered. The calculations of an induction electric motor with a squirrel-cage rotor are considered in two different ways: using the technique presented in [1], and using the ANSYS finite element analysis program Maxwell.