JWJie Wu

Jie Wu

*This is an algorithmically generated author record based on publicly available information.

Jie Wu has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Impact of Diesel Injection Strategy and In-Cylinder Temperature on the Combustion and Emissions of Ammonia/Diesel Dual-Fuel Marine Engine

    by Wei Guan, Songchun Luo, Jie Wu, Hua Lou, Lei Wang, Feng Wu, Li Li, Fuchuan Huang, Haibin He

    This study investigates the impact of different combustion control strategies on marine engine combustion and emission characteristics at a high ammonia energy ratio. Compared to the strategy of maintaining a constant fuel injection duration, the strategy of keeping the fuel injection pressure constant allows the kinetic energy of diesel to remain at a higher level. This results in an increase in combustion efficiency and indicated the thermal efficiency of the engine, while also reducing CO2 and soot emissions. However, when the ammonia energy ratio increases to more than 50%, the indicated thermal efficiency starts to decrease along with the increase in the emissions of N2O and unburned ammonia. To address these issues, one of the potential means is to improve the in-cylinder combustion environment by increasing the in-cylinder gas temperature. This can enhance combustion efficiency and ultimately optimize the performance and emission characteristics of dual-fuel engines, which results in an increase in the combustion efficiency to 98% and indicated thermal efficiency to 54.47% at a relatively high ammonia energy ratio of 60%. Emission results indicate that N2O emissions decrease from 1099 ppm to 25 ppm, while unburned ammonia emissions drop from 16016 ppm to 100 ppm. Eventually, the greenhouse gas emissions were reduced by about 85.3% in comparison with the baseline case.


  • Open Access

    Neural Network-Based Control Optimization for NH3 Leakage and NOx Emissions in SCR Systems

    by Weiqi Li, Jie Wu, Dongwei Yao, Feng Wu, Lei Wang, Hua Lou, Haibin He

    This study proposes a data-driven optimization framework to enhance emission control performance in diesel engine selective catalytic reduction (SCR) systems under transient operating conditions. A one-dimensional SCR model was constructed in GT-Power, and simulation datasets were generated using experimentally measured inputs from the World Harmonized Transient Cycle (WHTC), with representative emission responses obtained by varying fixed ammonia-to-NOx (A/N) ratios. Building on these datasets, a hybrid prediction model combining Long Short-Term Memory (LSTM) networks and multi-head attention mechanisms was developed to accurately forecast SCR outlet NH3 leakage and NOx emissions. The model exhibited high predictive accuracy, achieving R2 values exceeding 0.977 and low RMSE across training, validation, and test sets. Based on the model predictions, a constrained dynamic multi-objective optimization strategy was implemented to adaptively adjust ammonia dosing, aiming to simultaneously minimize NH3 leakage and NOx emissions. The optimized NH3 injection profiles were validated through reapplication in the GT-Power simulation environment. Compared to the baseline fixed-ratio control strategy, the proposed approach reduced NH3 leakage and NOx emissions by 34.40% and 11.15%, respectively, as determined for the transient segment of the WHTC cycle. These results demonstrate the effectiveness of integrating physics-based simulation, deep learning prediction, and dynamic optimization for improving aftertreatment adaptability and emission compliance in real-world diesel engine applications. All reported values are based on a single simulated WHTC cycle without statistical uncertainty analysis.


  • Simulation and analysis of the crankshaft system of the high-power marine engine

    by Huijun Zhao, Jie Wu, Haibin He, Yang Xiao, Lei Wang, Hua Lou, Kaimin Liu, Xiaodong Ruan

    The crankshaft is one of the most important parts of the engine and is likened to the "backbone" of the engine. In this paper, NL9340 high power diesel engine crankshaft system as the research object, the finite element free mode simulation model of crankshaft was established, and the inherent frequency and vibration mode of crankshaft were calculated. Through the rigid-flexible coupling finite element simulation of the crankshaft system, the dynamic and kinematic characteristics of the crankshaft system were analyzed. It was calculated that the load spectrum of each cylinder connecting rod journal and piston pin mainly fluctuated in the range of 20000 kN, in which the maximum exciting forces of the first connecting rod journal and the second connecting rod journal are above 30000 kN. On this basis, the static strength of the crankshaft was simulated and analyzed. The results show that the stress is the greatest and most concentrated at the over-rounded corner between connecting rod journal and crank. The maximum equivalent stress and deformation occur at the second cylinder connecting rod journal, which are 14.103 MPa and 8.3683 e-3 mm respectively.


  • Open Access

    Optimization Analysis of Various Parameters Based on Response Surface Methodology for Enhancing NOx Catalytic Reduction Performance of Urea Selective Catalytic Reduction on Cu-ZSM-13 Catalyst

    by Weiqi Li, Jie Wu, Dongwei Yao, Feng Wu, Lei Wang, Hua Lou, Haibin He, Jingyi Hu

    While selective catalytic reduction (SCR) has long been indispensable for nitrogen oxide (NOx) removal, optimizing its performance remains a significant challenge. This study investigates the combined effects of structural and intake parameters on SCR performance, an aspect often overlooked in previous research. This paper innovatively developed a three-dimensional SCR channel model and employed response surface methodology to conduct an in-depth analysis of multiple key factors. This multidimensional, multi-method approach enables a more comprehensive understanding of SCR system mechanics. Through target optimization, we achieved a simultaneous improvement in three critical indicators: the NOx conversion rate, pressure drop, and ammonia slip. It is worth noting that the NOx conversion rate has been optimized from 17.07% to 98.25%, the pressure drop has been increased from 3454.62 Pa to 2558.74 Pa, and the NH3 slip has been transformed from 122.26 ppm to 17.49 ppm. These results not only advance the theoretical understanding of SCR technology but also provide valuable design insights for practical applications. Our findings pave the way for the development of more efficient and environmentally friendly SCR systems, potentially revolutionizing NOx control in various industries.

  • Open Access

    An Experimental Study on the Flash Boiling Characteristics of Liquid Ammonia Spray in a Constant Volume Chamber under High Injection Pressure

    by Haibin He, Jie Wu, Lei Wang, Hua Lou, Songfeng Li, Lvmeng Huang, Zhanming Chen

    The spray characteristics of liquid ammonia under various ambient pressures and temperatures were analyzed in a constant volume chamber to cover a wide range of superheat degrees. The injection pressure was set as 70 and 80 MPa with ambient pressure ranging from 0.2 to 4 MPa. The ambient temperature was 500 K. The results showed that the higher the injection pressure, the greater the kinetic energy obtained. The droplet fragmentation was enhanced, and the phenomenon of gradual separation of the gas–liquid region occurred with increasing injection pressure. Under flash boiling spray conditions, the spray developed faster than non-flash boiling and transition flash boiling spray under the same injection pressure. In addition, the flash boiling spray tip penetration of the gas and liquid increased more than that of cold spray, and the fluctuation of the late stage of the injection was relatively large. Therefore, the injection pressure has a greater effect on the spray tip penetration of flash boiling spray. Moreover, ambient pressure greatly influences the flare flash boiling spray. The spray resistance phenomenon was found during the spray development in the flare flash boiling condition. With the increase in ambient pressure, the spray tip penetration of flash boiling spray decreases due to the reduction in the pressure difference inside and outside the spray hole and the restriction of ambient gas. Meanwhile, owing to the low ambient pressure and ambient density, the liquid penetration in the initial phase of the flare flash boiling spray will be abnormally shorter than that of the non-flash boiling spray.