Luke Arabskyj
Luke Arabskyj has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Christopher J. Chunnilall
National Physical Laboratory, Teddington, U.K.
4 shared publications - Marco Lucamarini
University of York
3 shared publications - Philip R. Dolan
National Physical Laboratory
3 shared publications - Ted Silva Santana
National Physical Laboratory 1 , Hampton Road, Teddington TW11 0LW
3 shared publications - Benyam Dejen
National Physical Laboratory 1 , Hampton Road, Teddington TW11 0LW
2 shared publications - A. Vaquero-Stainer
National Physical Laboratory 1 , Hampton Road, Teddington TW11 0LW
1 shared publication
Latest Publications
- Open Access
- 19 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (5) , 1815-1821
Characterisation of a Low-Noise Tuneable Silicon Single-Photon Avalanche Diode
Silicon single-photon avalanche diodes (Si-SPADs) are widely used in lightwave applications such as quantum communication, medical imaging, time-of-flight systems and quantum optical metrology, due to their sensitivity, accuracy, compactness and cost-effectiveness. The most important performance metric depends on its intended application. Each metric has a dependence on operating parameters such as bias voltage and operating temperature. Some metrics, e.g. detection efficiency and timing precision, exhibit performance trade-offs with noise. However, plug-and-play Si-SPADs typically have fixed bias voltage and operating temperature, which significantly limits user control, adaptability, and performance. In this study, a recently developed commercially available free-space Si-SPAD with adjustable bias voltage, temperature control, an integrated frequency counter and a large sensing area was evaluated. Key performance metrics were traceably measured as functions of bias voltage and temperature, including dark count rate, dead time, timing precision, afterpulse probability and photon detection efficiency at 852 nm. Results are benchmarked against existing reports of other commercially available Si-SPAD detectors. Notable strengths include low dark count rates (4 to 10 s-1), a large sensing area (diameter = 500 μm), and high timing precision (163 to 212ps), whilst maintaining a detection efficiency greater than 40%. These characteristics make the detector a strong candidate for deployment across a range of applications, particularly those operating outside of lab conditions where operational flexibility is essential.
- 19 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 44 (5) , 1815-1821
Open AccessCharacterisation of a Low-Noise Tuneable Silicon Single-Photon Avalanche Diode
Silicon single-photon avalanche diodes (Si-SPADs) are widely used in lightwave applications such as quantum communication, medical imaging, time-of-flight systems and quantum optical metrology, due to their sensitivity, accuracy, compactness and cost-effectiveness. The most important performance metric depends on its intended application. Each metric has a dependence on operating parameters such as bias voltage and operating temperature. Some metrics, e.g. detection efficiency and timing precision, exhibit performance trade-offs with noise. However, plug-and-play Si-SPADs typically have fixed bias voltage and operating temperature, which significantly limits user control, adaptability, and performance. In this study, a recently developed commercially available free-space Si-SPAD with adjustable bias voltage, temperature control, an integrated frequency counter and a large sensing area was evaluated. Key performance metrics were traceably measured as functions of bias voltage and temperature, including dark count rate, dead time, timing precision, afterpulse probability and photon detection efficiency at 852 nm. Results are benchmarked against existing reports of other commercially available Si-SPAD detectors. Notable strengths include low dark count rates (4 to 10 s-1), a large sensing area (diameter = 500 μm), and high timing precision (163 to 212ps), whilst maintaining a detection efficiency greater than 40%. These characteristics make the detector a strong candidate for deployment across a range of applications, particularly those operating outside of lab conditions where operational flexibility is essential.
- Open Access
- 4 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (19)
Interference effects in commercially available free-space silicon single-photon avalanche diodes
Single-photon avalanche diodes (SPADs) are essential for photon-based measurements and metrology, enabling measurement comparisons at the few-photon level and facilitating global traceability to the SI. A spatially uniform detector response is crucial for these applications. Here, we report on interference effects in commercially available silicon SPADs that are detrimental to their spatial uniformity. Contrasts as high as 18% are observed, posing problems for metrology and general applications that utilize coherent light and require stable detection efficiencies. We eliminate the device optical window as a contributing interface, isolating likely causes to anti-reflective coatings, the semiconductor surface, and the SPAD's internal structure. We also present results where we leverage this sub-optimal behavior by aligning an incident beam with the position of maximum constructive interference, yielding an effective detection efficiency of 51.1(1.7)% compared to the normal value of 44.3(1)% obtained with the interference suppressed. We anticipate that this work will significantly impact the continuing development of these devices, the methods for characterizing them, and their use in accurate measurements.
- 4 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (19)
Open AccessInterference effects in commercially available free-space silicon single-photon avalanche diodes
Single-photon avalanche diodes (SPADs) are essential for photon-based measurements and metrology, enabling measurement comparisons at the few-photon level and facilitating global traceability to the SI. A spatially uniform detector response is crucial for these applications. Here, we report on interference effects in commercially available silicon SPADs that are detrimental to their spatial uniformity. Contrasts as high as 18% are observed, posing problems for metrology and general applications that utilize coherent light and require stable detection efficiencies. We eliminate the device optical window as a contributing interface, isolating likely causes to anti-reflective coatings, the semiconductor surface, and the SPAD's internal structure. We also present results where we leverage this sub-optimal behavior by aligning an incident beam with the position of maximum constructive interference, yielding an effective detection efficiency of 51.1(1.7)% compared to the normal value of 44.3(1)% obtained with the interference suppressed. We anticipate that this work will significantly impact the continuing development of these devices, the methods for characterizing them, and their use in accurate measurements.
- Open Access
- 4 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (19)
A refined method for characterizing afterpulse probability in single-photon avalanche diodes
Single-photon avalanche diodes (SPADs) are critical components in low-light-level sensing and photonic quantum information applications. For these, it is often necessary that a full characterization of the SPAD is performed, for which a key metric is the afterpulse probability. This study provides a detailed comparison of the common synchronized and non-synchronized methods used to measure afterpulse probability. Measurements on a single SPAD reveal inconsistencies between the afterpulse probabilities obtained by the two methods. By re-deriving the equations from first principles, the discrepancy is traced to the analysis approach for the non-synchronized experiment. An improved analysis approach is presented, leading to better agreement between the non-synchronized and synchronized methods. The study also provides guidance on the experimental conditions required for the valid application of both methods, along with a detailed analysis of the limitations of the non-synchronized method under high photon flux. These findings offer a more accurate approach for characterizing afterpulse probability and for reconciling the results of two methods, which enables better quantification of SPAD performance.
- 4 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (19)
Open AccessA refined method for characterizing afterpulse probability in single-photon avalanche diodes
Single-photon avalanche diodes (SPADs) are critical components in low-light-level sensing and photonic quantum information applications. For these, it is often necessary that a full characterization of the SPAD is performed, for which a key metric is the afterpulse probability. This study provides a detailed comparison of the common synchronized and non-synchronized methods used to measure afterpulse probability. Measurements on a single SPAD reveal inconsistencies between the afterpulse probabilities obtained by the two methods. By re-deriving the equations from first principles, the discrepancy is traced to the analysis approach for the non-synchronized experiment. An improved analysis approach is presented, leading to better agreement between the non-synchronized and synchronized methods. The study also provides guidance on the experimental conditions required for the valid application of both methods, along with a detailed analysis of the limitations of the non-synchronized method under high photon flux. These findings offer a more accurate approach for characterizing afterpulse probability and for reconciling the results of two methods, which enables better quantification of SPAD performance.
- Open Access
- 9 September 2024
- Published by IOP Publishing in Metrologia
- Vol. 61 (5) , 055008
Traceable characterisation of fibre-coupled single-photon detectors
The detection of single photons plays an essential role in advancing single-photon science and technologies. Yet, within the visible/near-infrared spectral region, accurate fibre-based optical power measurements at the few-photon level are not yet well-established. In this study, we report on a fibre-based setup, enabling traceable optical power measurements at the few-photon level in this spectral region. The setup was used to calibrate the detection efficiency (DE) of four single-photon avalanche diode (SPAD) detectors. The relative standard uncertainties on the mean DE values obtained from repeat fibre-to-detector couplings ranged from 0.67% to 0.81% (k = 2). However, the relative standard deviation of DE values, which ranged from 1.38% to 3.20% (k = 2), poses a challenge for the metrology of these devices and applications that require high accuracy and repeatability. We investigated the source of these variations by spatially mapping the response of a detector’s fibre connector port, using a focused free-space beam, allowing us to estimate the detector’s spatial non-uniformity. In addition, we realise a novel calibration approach for fibre-coupled SPADs in a free-space configuration, enabling a direct comparison between the fibre-based setup and the National Physical Laboratory’s established free-space facility using a single SPAD. Finally, we investigated alternative coupling methods, testing the repeatability of different fibre-to-fibre connectors in addition to direct fibre-to-detector couplings: SPADs from three manufacturers were tested, with both single-mode and multi-mode fibre.
- 9 September 2024
- Published by IOP Publishing in Metrologia
- Vol. 61 (5) , 055008
Open AccessTraceable characterisation of fibre-coupled single-photon detectors
The detection of single photons plays an essential role in advancing single-photon science and technologies. Yet, within the visible/near-infrared spectral region, accurate fibre-based optical power measurements at the few-photon level are not yet well-established. In this study, we report on a fibre-based setup, enabling traceable optical power measurements at the few-photon level in this spectral region. The setup was used to calibrate the detection efficiency (DE) of four single-photon avalanche diode (SPAD) detectors. The relative standard uncertainties on the mean DE values obtained from repeat fibre-to-detector couplings ranged from 0.67% to 0.81% (k = 2). However, the relative standard deviation of DE values, which ranged from 1.38% to 3.20% (k = 2), poses a challenge for the metrology of these devices and applications that require high accuracy and repeatability. We investigated the source of these variations by spatially mapping the response of a detector’s fibre connector port, using a focused free-space beam, allowing us to estimate the detector’s spatial non-uniformity. In addition, we realise a novel calibration approach for fibre-coupled SPADs in a free-space configuration, enabling a direct comparison between the fibre-based setup and the National Physical Laboratory’s established free-space facility using a single SPAD. Finally, we investigated alternative coupling methods, testing the repeatability of different fibre-to-fibre connectors in addition to direct fibre-to-detector couplings: SPADs from three manufacturers were tested, with both single-mode and multi-mode fibre.