BFBrenden Ferland

Brenden Ferland

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Brenden Ferland has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Tuning graphene oxide performance across diverse applications by oxidation-extent fractionation of a single batch

    by Harish V. Kumar, Brenden Ferland, Vignesh Vasu, Alessandro Palmieri, William E. Mustain, Laura Gonzalez-Fajardo, Will Dickinson, Hannes C. Schniepp, Xiuling Lu, Sudeep R. Bapat, et al.

    Graphene oxide (GO) produced by Hummers-type methods comprises sheets with varying degrees of oxidation, yet most studies treat GO as being uniform. Here, we fractionate GO via emulsion-based partitioning, with highly oxidized sheets remaining in the aqueous phase (GOw) and less-oxidized sheets stabilizing the oil/water interface (GOe). The resulting fractions exhibit different properties across five tested domains. Contact angles range from 63°(GOw) to 92°(GOee). GOw films transmit 90.2% at 550 nm versus 84.1% for GOee, and microwave reduction decreases GOw transmittance about four times as much as the less-oxidized GOee fraction (4.34% vs 1.07%). PEG-conjugated GOew maintained A549 cell viability above 80% at all dilutions, while GOw and unfractionated GO remained non-cytotoxic at the lower concentrations. GOe-PEG reduced viability at most dilutions. In PVAc composites at 1 wt%, the most-oxidized fraction GOw gave the largest modulus increase (34%), while unfractionated GO and the less-oxidized GOe gave smaller increases that were not statistically separable from each other. In lithium-ion half-cells, GOwww delivers 270 mAh/g at cycle 50, compared with 61 mAh/g for GOeee. Across the fractions generated from a single batch, four of the five property rankings

  • Open Access

    ResistaMet GUI: open-source electrical characterization for Keithley 2400 series sourcemeters

    by Brenden Ferland

    ResistaMet GUI is a desktop application for electrical characterization using Keithley 2400 series source measure units (SMUs) over a GPIB interface. These instruments are commonly used by electrical engineers, materials scientists, and other physical scientists to characterize electrically active devices and materials. This software is benchwritten and tested with 6 primary measurement modes: two-and four-wire resistance, constant-voltage and constantcurrent biasing for long runs (with in-run event annotations), I-V sweep, collinear 4-point probe per ASTM F84, and van der Pauw per ASTM F76 Method A. Each reading carries an instrument uncertainty propagated from the Keithley datasheet’s per-range accuracy specs, all the way through to derived quantities like sheet resistance and resistivity. An in-package Keithley simulator, calibrated against captured SCPI traces from our bench Keithley 2420 and replayed in CI, allows users to test and practice each mode without an SMU, and keeps documented hardware quirks from regressing.

  • Open Access

    Moisture-driven electric power generation using graphene-based hydrogels for sustained power output and self-powered sensing

    by Nishadi M. Bandara, Jinzhou Liu, Brenden Ferland, Mahdad Mahmoudi, Douglas H. Adamson

    Moist electric generators (MEGs) produce electric power from hydration gradients and have been identified as a promising sustainable technology for advanced energy systems. This article reports the fabrication of a graphene-templated poly(acrylic acid) (PAA) hydrogel MEG with a gradient distribution of PAA swelling resulting from variations in polymer confinement. The MEG delivers an open-circuit voltage of 0.78 V for over 120 hours under ambient environmental conditions with a power density of 62 mW m−2. The MEG effectively operates at temperatures as low as −25 °C. A current output of 780 µA has been achieved through a parallel configuration of MEG elements, and an output of 18 V has been achieved using a series configuration. The electric output of the MEGs can be scaled and is shown to power various commercial electronics, including LEDs, an 8-digit calculator, and a humidity sensor with an LCD screen. Additionally, the MEG is shown to perform as a self-powered tactile sensor.


  • Open Access

    Interfacial Self-Assembly of Graphene Networks at 1 vol% Enables Piezoresistive and Electrothermal Silicone Foams

    by Brenden Ferland, Douglas Adamson

    Segregated network composites achieve electrical percolation at minimal filler loadings by localizing conductivity to architectural boundaries. However, achieving this architecture typically requires tedious multi-step processing, often incompatible with scalable manufacturing. Here, we report the single-step synthesis of a silicone composite segregated network composed of self-assembled percolating graphene networks. These networks are templated by graphene-stabilized water-in-oil emulsions, created by spontaneous exfoliation of graphite at oil/water interfaces generated by agitation. After polymerization of the silicone and removal of the dispersed aqueous phase, the resulting foams achieve conductivities of 0.43 S/m at a 1.37 vol% loading of graphene. This is a 12-fold reduction compared to prior interfacial assembly methods, which require 16.5 vol% loading and thousands of hours of processing to achieve comparable electrical conductivity. Architectural segregation decouples mechanical and electrical properties, enabling application-specific modulus tuning. The foams exhibit reversible piezoresistance with a U-shaped strain response, are stable through 5000 cycles, and provide voltage-controlled heating to 143 °C at milliamp current densities, three orders of magnitude lower than those of continuous CVD graphene networks. The low thermal mass of the air-filled foam structure provides rapid thermal response, achieving 28-second de-icing from -17 °C.

  • Transparent conductive PEDOT–graphene films from large-flake graphite

    by Sean T. McDermott, Brenden Ferland, Jinzhou Liu, Prabodha Abeykoon, Michael J. Joyce, Seth Shuster, Steven L. Suib, Douglas H. Adamson


  • Open Access

    Transparent conductive PEDOT–graphene films from large- flake graphite

    by Sean McDermott, Brenden Ferland, Jinzhou Liu, Prabodha Abeykoon, Michael Joyce, Seth Shuster, Steven Suib, Douglas Adamson

    The demand for affordable, flexible, transparent, and robust thin film electrodes in organic electronics has highlighted the limitations of indium tin oxide (ITO), which suffers from fragility and high costs. Poly(3,4- ethylenedioxythiophene) (PEDOT), particularly when doped with poly(styrene sulfonate) (PSS), has emerged as a promising alternative due to its mechanical flexibility, electrical conductivity, and environmental stability. However, PSS's insulating nature, hygroscopicity, and acidity present significant drawbacks. This study explores an alternative approach using large-flake graphene, exfoliated through a solvent interface trapping method (SITM), as a dopant for PEDOT. The resulting PEDOT-graphene films exhibit conductivities reaching 1070 S/cm, surpassing those of previously reported PEDOT-based films. The graphene sheets, acting as templates during vapor-phase polymerization (VPP) of PEDOT, enhance the film's conductivity by increasing electron pathways and crystalline regions within PEDOT. Characterization through SEM, TEM, XRD, Raman spectroscopy, XPS, and UV-Vis spectroscopy confirms the structural and electrical integrity of the films. Additionally, these films demonstrate potential applications in sensing technologies, particularly responsive to volatile organic compounds such as triethylamine. This work presents a scalable method for producing high-conductivity, transparent PEDOT- graphene films, offering a viable alternative to ITO in organic electronic applications.