Valle Chozas Ligero
Research Subjects
Valle Chozas Ligero has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Rafael Ruiz
Laboratorio de Estructuras Universidad Politécnica de Madrid, E.T.S. Ingenieros de Caminos, Canales y Puertos Madrid Spain
3 shared publications - Hugo Corres
Universidad Politécnica de Madrid
2 shared publications - Leonardo Todisco
E.T.S. Ingenieros de Caminos, Canales y Puertos, Laboratorio de Estructuras Universidad Politécnica de Madrid Madrid Spain
2 shared publications - Elisabete R. Teixeira
University of Minho
1 shared publication - Joaquim Tinoco
Department of Civil Engineering, University of Minho, ISISE, 4800-058 Guimarães, Portugal
1 shared publication - Jose Campose Matos
Department of Civil Engineering, ISISE, ARISE, University of Minho, 4800-058 Guimarães, Portugal
1 shared publication
Latest Publications
- Open Access
- 18 November 2026
- Published by Springer Nature
- p. 890-897
Life Cycle Assessment of Geopolymer Precast Slab for the Road Pavements: A Comparative Study with a Conventional Concrete Precast Slab
Road infrastructure plays a vital role in supporting economic development, but it also generates significant environmental and social implications that must be carefully managed. Consequently, identifying sustainable alternatives to conventional concrete is critical in the development of the environmentally responsible road infrastructure. This study investigates geopolymer precast slabs made from activated fly ash (FA) and Ground Granulated Blast-furnace Slag (GGBS) as a substitute for conventional Ordinary Portland Cement (OPC) slabs. A life cycle assessment (LCA) was conducted on the slabs using the CML methodology in SimaPro with a ‘cradle-to-site’ approach. Results show that geopolymer slabs reduce CO 2 emissions by 44% per slab compared to conventional slabs, and by nearly 78% at the concrete level. While transportation of materials increases emissions relative to conventional slabs, the overall environmental impact of geopolymer slabs remains lower Despite this, geopolymer solutions offer advantages such as enhanced durability, chemical resistance, and lower water consumption, highlighting their potential as a sustainable alternative. Optimizing supply chains and using locally available precursors could further improve overall sustainability.
- 18 November 2026
- Published by Springer Nature
- p. 890-897
Open AccessLife Cycle Assessment of Geopolymer Precast Slab for the Road Pavements: A Comparative Study with a Conventional Concrete Precast Slab
Road infrastructure plays a vital role in supporting economic development, but it also generates significant environmental and social implications that must be carefully managed. Consequently, identifying sustainable alternatives to conventional concrete is critical in the development of the environmentally responsible road infrastructure. This study investigates geopolymer precast slabs made from activated fly ash (FA) and Ground Granulated Blast-furnace Slag (GGBS) as a substitute for conventional Ordinary Portland Cement (OPC) slabs. A life cycle assessment (LCA) was conducted on the slabs using the CML methodology in SimaPro with a ‘cradle-to-site’ approach. Results show that geopolymer slabs reduce CO 2 emissions by 44% per slab compared to conventional slabs, and by nearly 78% at the concrete level. While transportation of materials increases emissions relative to conventional slabs, the overall environmental impact of geopolymer slabs remains lower Despite this, geopolymer solutions offer advantages such as enhanced durability, chemical resistance, and lower water consumption, highlighting their potential as a sustainable alternative. Optimizing supply chains and using locally available precursors could further improve overall sustainability.
- 29 December 2024
- Published by Springer Nature
- p. 120-127
Reducing Embodied Carbon and Enhancing Performance in Bridge Construction Using High-Performance Steel Fibre Reinforced Concrete
- 29 December 2024
- Published by Springer Nature
- p. 120-127
Reducing Embodied Carbon and Enhancing Performance in Bridge Construction Using High-Performance Steel Fibre Reinforced Concrete
- Open Access
- 4 February 2024
- Published by Wiley in Structural Concrete
- Vol. 25 (2) , 935-955
Experimental characterization of a cost‐competitive tailor‐made HPFRC mix design for wide application in precast girder of roadway bridges
This paper presents a comprehensive study on the development of a cost‐effective, high‐performance fiber reinforced concrete (HPFRC) for the construction of a 60 m‐span U‐girder roadway bridge without stirrups in the webs, meeting the design requirements of fck ≥ 100 MPa and the post‐cracking flexural strength fR3k ≈ 8–10 MPa. The main objective of this research is to develop a F5 workability class HPFRC that meets the specified design criteria without exceeding 2.5–3.0 times the cost of a C70/85. To achieve this goal, the concrete mix was obtained using 500 kg/m3 of cement and 50 kg/m3 of silica fume. This mix was investigated with nine different combinations of fibers and fiber contents, resulting that 80 kg/m3 of 4D‐fibers (lf = 60 mm) provided the optimal fR3k without compromising workability and cost. Subsequently, an extensive experimental campaign was conducted to cast the U‐girder following the conventional casting techniques involving casting prismatic samples, L‐shaped and rectangular‐shaped panels to represent different parts of the U‐girder. Innovative techniques were used to study the effect of different waiting times between concrete pours. Results from the testing of the prismatic specimens evidenced the need of stitching by means of a poker vibrator planes between successive concrete layers. Furthermore, the study of the panels evidenced that a waiting time of 90 min allows the HPFRC to achieve enough bending and compressive strength to bear internal vibration of the element without liquefying and, at the same time, avoiding cold joints. The results confirm the applicability of the developed HPFRC for the structural element under study following conventional casting techniques.
- 4 February 2024
- Published by Wiley in Structural Concrete
- Vol. 25 (2) , 935-955
Open AccessExperimental characterization of a cost‐competitive tailor‐made HPFRC mix design for wide application in precast girder of roadway bridges
This paper presents a comprehensive study on the development of a cost‐effective, high‐performance fiber reinforced concrete (HPFRC) for the construction of a 60 m‐span U‐girder roadway bridge without stirrups in the webs, meeting the design requirements of fck ≥ 100 MPa and the post‐cracking flexural strength fR3k ≈ 8–10 MPa. The main objective of this research is to develop a F5 workability class HPFRC that meets the specified design criteria without exceeding 2.5–3.0 times the cost of a C70/85. To achieve this goal, the concrete mix was obtained using 500 kg/m3 of cement and 50 kg/m3 of silica fume. This mix was investigated with nine different combinations of fibers and fiber contents, resulting that 80 kg/m3 of 4D‐fibers (lf = 60 mm) provided the optimal fR3k without compromising workability and cost. Subsequently, an extensive experimental campaign was conducted to cast the U‐girder following the conventional casting techniques involving casting prismatic samples, L‐shaped and rectangular‐shaped panels to represent different parts of the U‐girder. Innovative techniques were used to study the effect of different waiting times between concrete pours. Results from the testing of the prismatic specimens evidenced the need of stitching by means of a poker vibrator planes between successive concrete layers. Furthermore, the study of the panels evidenced that a waiting time of 90 min allows the HPFRC to achieve enough bending and compressive strength to bear internal vibration of the element without liquefying and, at the same time, avoiding cold joints. The results confirm the applicability of the developed HPFRC for the structural element under study following conventional casting techniques.