Han Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Han Wang has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Lei Zhang
School of Water Conservancy and Civil Engineering, Northeast Agricultural University, Harbin 150030, China
1 shared publication - Qiang Fu
State Key Laboratory of Rice Biology and Breeding, China National Rice Research Institute, Hangzhou, China
1 shared publication - Ruisen Li
College of Civil Engineering & Architecture, Qingdao Agricultural University, Qingdao 266109, China
1 shared publication - Sheng Li
School of Software Engineering, Jiangxi University of Science and Technology, Nanchang 330013, China
1 shared publication - Wei Wang
School of Civil Engineering, Harbin Institute of Technology, Harbin 150090, China
1 shared publication - Yishu Zhang
Key Laboratory of Structures Dynamic Behaviour and Control of the Ministry of Education, Harbin Institute of Technology, Harbin 150090, China
1 shared publication
Latest Publications
- Open Access
Mechanical Strength and Hydration Characteristic of Multiple Common Waste-Blended Cement-Based Materials Cured by Electric-Induced Heating Curing Under Severely Cold Environments
To address the challenges of concrete construction in polar regions, this study investigates the feasibility of fabricating cement-based materials under severely low temperatures using electric-induced heating curing methods. Cement mortars incorporating fly ash (FA-CM), ground granulated blast furnace slag (GGBS-CM), and metakaolin (MK-CM) were cured at environmental temperatures of −20 °C, −40 °C, and −60 °C. The optimal carbon fiber (CF) contents were determined using the initial electric resistivity to ensure a consistent electric-induced heating curing process. The thermal profiles during curing were monitored, and mechanical strength development was systematically evaluated. Hydration characteristics were elucidated through thermogravimetric analysis (TG), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) to identify phase compositions and reaction products. Results demonstrate that electric-induced heating effectively mitigates the adverse effect caused by the ultra-low temperature constraints, with distinct differences in the strength performance and hydration kinetics among supplementary cementitious materials. MK-CM exhibited superior early strength development with strength increasing rates above 10% compared to the Ref. specimen, which was attributed to the accelerated pozzolanic reactions. Microstructural analyses further verified the macroscopic strength test results that showed that electric-induced heating curing can effectively promote the performance development even under severely cold environments with a higher hydration degree and refined micro-pore structure. This work proposes a viable strategy for polar construction applications.
Open AccessMechanical Strength and Hydration Characteristic of Multiple Common Waste-Blended Cement-Based Materials Cured by Electric-Induced Heating Curing Under Severely Cold Environments
To address the challenges of concrete construction in polar regions, this study investigates the feasibility of fabricating cement-based materials under severely low temperatures using electric-induced heating curing methods. Cement mortars incorporating fly ash (FA-CM), ground granulated blast furnace slag (GGBS-CM), and metakaolin (MK-CM) were cured at environmental temperatures of −20 °C, −40 °C, and −60 °C. The optimal carbon fiber (CF) contents were determined using the initial electric resistivity to ensure a consistent electric-induced heating curing process. The thermal profiles during curing were monitored, and mechanical strength development was systematically evaluated. Hydration characteristics were elucidated through thermogravimetric analysis (TG), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR) to identify phase compositions and reaction products. Results demonstrate that electric-induced heating effectively mitigates the adverse effect caused by the ultra-low temperature constraints, with distinct differences in the strength performance and hydration kinetics among supplementary cementitious materials. MK-CM exhibited superior early strength development with strength increasing rates above 10% compared to the Ref. specimen, which was attributed to the accelerated pozzolanic reactions. Microstructural analyses further verified the macroscopic strength test results that showed that electric-induced heating curing can effectively promote the performance development even under severely cold environments with a higher hydration degree and refined micro-pore structure. This work proposes a viable strategy for polar construction applications.
- Open Access
Performance Improvement of Steel Fiber Reinforced High-Performance Concrete Cured by Electric-Induced Heating Under Negative Temperature by Mix Proportion Optimization
To address the insufficient early strength development of steel-fiber-reinforced high-performance concrete (SF-HPC) under subzero temperatures, this study proposes an electric-induced heating curing method for SF-HPC fabrication at −20 °C. The effects of mix parameters, including steel fiber content, water-to-binder ratio, silica fume dosage, and fine aggregate gradation, on the curing temperature and mechanical properties of SF-HPC were systematically investigated. The optimal mix proportion was identified through the curing temperature and compressive strength development for the specimens. Results revealed that compressive strength initially increased and then decreased with higher silica fume content and fine aggregate replacement ratios, while increased water-to-binder ratios positively influenced curing efficiency and strength development. The optimal mix comprised 2.0 vol% steel fibers, a water-to-binder ratio of 0.22, 20% silica fume, and 60% fine aggregate replacement. Further, comparative analyses of electric-induced heating curing, room-temperature curing, and high-temperature steam curing revealed that electric-induced heating curing can promote the strength formation of SF-HPC in a negative-temperature environment. Microstructural characterization via BET analysis demonstrated that electric-induced heating curing refined the pore structure of SF-HPC. These findings highlight the benefits of electric-induced heating as an efficient strategy for fabricating SF-HPC in cold climates, providing theoretical and practical insights for winter construction.
Open AccessPerformance Improvement of Steel Fiber Reinforced High-Performance Concrete Cured by Electric-Induced Heating Under Negative Temperature by Mix Proportion Optimization
To address the insufficient early strength development of steel-fiber-reinforced high-performance concrete (SF-HPC) under subzero temperatures, this study proposes an electric-induced heating curing method for SF-HPC fabrication at −20 °C. The effects of mix parameters, including steel fiber content, water-to-binder ratio, silica fume dosage, and fine aggregate gradation, on the curing temperature and mechanical properties of SF-HPC were systematically investigated. The optimal mix proportion was identified through the curing temperature and compressive strength development for the specimens. Results revealed that compressive strength initially increased and then decreased with higher silica fume content and fine aggregate replacement ratios, while increased water-to-binder ratios positively influenced curing efficiency and strength development. The optimal mix comprised 2.0 vol% steel fibers, a water-to-binder ratio of 0.22, 20% silica fume, and 60% fine aggregate replacement. Further, comparative analyses of electric-induced heating curing, room-temperature curing, and high-temperature steam curing revealed that electric-induced heating curing can promote the strength formation of SF-HPC in a negative-temperature environment. Microstructural characterization via BET analysis demonstrated that electric-induced heating curing refined the pore structure of SF-HPC. These findings highlight the benefits of electric-induced heating as an efficient strategy for fabricating SF-HPC in cold climates, providing theoretical and practical insights for winter construction.