FCFeng Cheng

Feng Cheng

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Feng Cheng has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A 15-MHz, 2.7-mm 2 Notch-Free Hybrid Magnetic Current Sensor With Feedforward Ripple Cancellation and ±0.8% Local Gain Non-Uniformity

    by Feng Cheng, Jianlin Xia, Encheng Zhu, Long Zhang, Zhongyuan Fang, Xiaofeng Sun, Dejin Wang, Shaoping Li, Jing Zhu, Yongjia Li, et al.

    This article proposes a hybrid magnetic current sensor achieving a 15-MHz bandwidth within a compact 2.7-mm2 area. To mitigate the pole–zero mismatch inherent in the two-stage integrator topology, a dual-output Gm-C integrator with subtractor-based compensation is proposed, achieving a ±0.8% local gain non-uniformity. A wideband feedforward ripple suppression scheme cancels chopping ripple without bandwidth degradation, achieving 25-dB suppression while avoiding in-band notches common in ripple reduction loop (RRL) schemes. In addition, two active capacitor-boosting techniques enhance the effective capacitance in the DC servo loop (DCSL) and the differential difference amplifier (DDA), realizing significant passive area savings. While the Hall sensitivity drift is compensated by bias current with a positive temperature coefficient (PTC), a negative-temperature-coefficient (NTC) ground technique is proposed to stabilize the Hall-plate common-mode (CM) output. Compared with the state of the art, the proposed sensor achieves $3\times $ higher bandwidth, $1.5\times $ improved gain flatness, and 30% smaller chip area.

  • A 10-MHz, 2.3-mm² Hybrid Magnetic Current Sensor Using Gain–Bandwidth Decoupled DDA and Passive-Aided Bandwidth Extension

    by Yongjia Li, Feng Cheng, Jianlin Xia, Encheng Zhu, Long Zhang, Zhongyuan Fang, Xiaofeng Sun, Dejin Wang, Weifeng Sun

    This paper presents a wide bandwidth hybrid current sensor that incorporates a wideband instrumentation amplifier (IA) in the low-frequency (LF) path and a high gain-bandwidth product (GBW) integrator in the high-frequency (HF) path. The ping-pong switched-capacitor demodulator (PPSCD) in the LF path effectively suppresses ripple while introducing negligible gain non-uniformity. A two-stage integrator topology is adopted in the HF path to extend bandwidth and reduce noise compared to its single-stage counterpart. The implementation of a DC servo loop with an attenuator around the HF integrator minimizes offset with reduced area overhead. Additional area savings are achieved by employing a gain-bandwidth decoupled differential difference amplifier (DDA), which combines signals from the LF Hall path and HF coil path, and incorporates a peripheral passive bypass path for bandwidth enhancement. The proposed design achieves a 10 MHz bandwidth in a compact 2.3 mm² area, representing a 2× bandwidth improvement and 40% area reduction compared to the state-of-the-art.


  • An 8.5 MHz 42 ppm/∘ C Relaxation Oscillator With Charge-Pump Delay Cancellation and Digital Chopping Demodulation

    by Yongjia Li, Jianlin Xia, Feng Cheng, Yifan Cao, Jin Wu, Encheng Zhu, Xiaofeng Sun, Dejin Wang, Long Zhang, Zhongyuan Fang, et al.

    This paper presents an RC oscillator featuring a mixed-signal compensation loop that simultaneously mitigates comparator offset, loop delay, switch on-resistance, and temperature dependency. The oscillator employs an auxiliary comparator, a charge pump and a differential difference amplifier (DDA)-based main comparator to suppress ramping voltage overshoots caused by device and loop imperfections. Moreover, the auxiliary comparator employs chopper and digital demodulation techniques to suppress its own offset, further enhancing the accuracy of the calibration loop. By generating both ramping and reference voltages, the proportional-to-absolute-temperature (PTAT) core ensures that the temperature coefficient (TC) of the oscillation frequency primarily depends on passive RC components. Fabricated in a 0.18 μm BCD process, the design achieves an average frequency TC of 42 ppm/∘C from -20 ∘C to 125 ∘C across 10 samples. Benefiting from the proposed architecture, the oscillator operates at 8.45 MHz with a fast startup calibration time of 50 μs.


  • A 2 MHz Bandwidth Area-Efficient Multipath Hall Sensor With a Residual Ripple of 4.1 μT

    by Yongjia Li, Feng Cheng, Jianlin Xia, Peng Su, Long Zhang, Zhongyuan Fang, Feng Lin, Encheng Zhu, Weifeng Sun

    This paper presents a multipath wide-bandwidth magnetic current sensor based on Hall effect. To simultaneously achieve wide bandwidth, minimal ripple and small area, the system incorporates a non-spun filter-free main path with offset elimination through a continuous-time compact auxiliary path. The auxiliary path cancels the main path offset via feedforward, alleviating the need for area-consuming blocking capacitor or DC servo loop. Therefore, the chip occupies only 1.52 mm2. To suppress ripple in the auxiliary path induced by spinning current, a ping-pong switch-capacitor (PPSC) filter is proposed which mitigates ripple by sampling and averaging in the forward path, with the system achieving a residual ripple of $4.1~{\mu }$ T. Compared with the state-of-the-art Hall sensor, it achieves $5{\times }$ bandwidth improvement, $2{\times }$ ripple reduction while occupying $5{\times }$ less area.