WSWoongje Sung

Woongje Sung

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Woongje Sung has a total of 38 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Impact of Active Cell Geometry on the Static Performance of 10-kV 4H-SiC JBS (Junction Barrier Schottky) Diodes

    by Hojung Lee, Justin Lynch, Stephen A. Mancini, Skylar Deboer, Miguel Hinojosa, Aivars Lelis, Woongje Sung

    This study investigates the influence of active cell geometry on the static performance of 10-kV 4H-Silicon Carbide (SiC) Junction Barrier Schottky (JBS) diodes. Two types of diodes were fabricated and characterized, one with a hexagonal cell and the other with a stripe cell. While forward conduction characteristics were comparable, the reverse leakage current of the hexagonal cell was more than two orders of magnitude lower than that of the stripe cell at 8 kV. 3D TCAD simulations revealed that this discrepancy stems from strong electric field concentrations both at the bottom corners of the P + junctions and at the center of the Schottky contact in the stripe structure. These localized fields reduce the Schottky barrier height and enhance electron injection. In contrast, the hexagonal cell exhibited a more uniform electric field distribution in both regions, effectively suppressing leakage current. These findings underscore the critical role of active cell geometry in achieving robust reverse blocking performance in ultra-high-voltage SiC JBS diodes by clarifying the physical mechanisms contributing to leakage current behavior.

  • Open Access

    Design Optimization of 600V 4H-SiC Lateral Bi-Directional MOSFET (L-BiD-MOSFET) with 3D TCAD Simulation

    by Seung Yup Jang, Skylar Deboer, Woongje Sung

    This paper presents the fabrication and characterization of a cell-to-cell integrated SiC lateral bi-directional MOSFET (L-BiD-MOSFET), with blocking performance analyzed through correlation of experimental results and 3D TCAD simulations. The fabricated devices exhibit a breakdown voltage of 600 V, notably lower than the 900 V predicted by 2D simulations. To address this discrepancy, 3D TCAD simulations were performed, which identified electric field crowding at the finger edges as the dominant factor limiting the breakdown voltage. To mitigate this effect, an extended P-top edge design was introduced, which increases the simulated breakdown voltage by more than 10%. Experimental results on devices incorporating the proposed design confirm improved breakdown capability, demonstrating good agreement with simulations. These results highlight the importance of accurate 3D simulation for edge effects in lateral structures. Overall, the proposed design strategy provides valuable guidance for the development of high-performance lateral bi-directional SiC power devices.

  • Open Access

    Comparative Study of 1.2kV 4H-SiC Bi-Directional MOSFET (BiD-MOS) Design Approaches: 2-Chip vs Monolithic Integration

    by Stephen A. Mancini, Dai Xin Chen, Seung Yup Jang, Andrew Binder, Richard Floyd, Robert Kaplar, Jack Flicker, Adam Morgan, Xiao Qing Song, Woongje Sung

    Several 1.2kV 4H-SiC Bi-Directional MOSFETs (BiD-MOS) design approaches were successfully fabricated and evaluated based on their electrical characteristics. Both monolithic integration design approaches exhibited negligible differences in conduction, blocking, and switching characteristics when compared to their 2-Chip counterpart. However, during the short-circuit withstand time testing, severe gate oscillations were observed in the 2-Chip design, which was not an issue present in either monolithic configuration. As a result of its robust electrical behavior, monolithic integration emerges as a promising design approach for developing efficient and reliable Bi-Directional Switches.

  • Open Access

    High-Voltage Performance Evaluation of 6.5 kV 4H-SiC JBSFET Architectures and MOSFET with Enhanced 3rd Quadrant Conduction

    by Shariare Hossain Rabbi, Justin Lynch, Stephen A. Mancini, Woongje Sung

    This paper reports on the comparative analysis of several 6.5 kV-rated 4H-SiC Junction Barrier Schottky integrated MOSFETs (JBSFETs) and 4H-SiC MOSFET to assess their forward conduction, 3 rd quadrant behavior, and blocking characteristics. Among different JBSFET architectures, the Island P+ JBSFET achieved nearly identical specific on-resistance (R on,sp ) to the nominal MOSFET while delivering superior 3 rd quadrant conduction and maintaining a high breakdown voltage. Further optimization of Schottky width demonstrated a trade-off between leakage suppression and 3 rd quadrant conduction efficiency that underscores the Island P+ JBSFET’s potential as a reliable high-voltage SiC power device for next-generation applications.

  • Open Access

    Edge Termination Design for Ultra High-Voltage (>10 kV) 4H-SiC Power Devices Using Background Doping Modulation (BDM)

    by Mohamed Torky, Justin Lynch, Nick Yun, Stephen Mancini, Miguel Hinojosa, Aivars Lelis, Woongje Sung

    Achieving reliable breakdown in ultra-high-voltage (>10 kV) SiC devices is limited by edge termination design, where low epitaxial doping (~4×10¹⁴ cm⁻³) results in lateral straggle to be more prominent, therefore necessitating wider spacing between Aluminum implants in conventional floating field rings (FFRs). This study introduces a background doping modulation (BDM) scheme, incorporating a moderately doped N-type confinement region within P+ rings, enabling tighter spacing without added process complexity for high-voltage MOSFETs. Fabricated BDM-FFRs achieved >13 kV breakdown (30% higher than conventional FFRs), with leakage current <10 nA at 10 kV, while reducing termination area by 18.6%. Therefore, the BDM-FFR demonstrates a scalable, compact, and high-performance edge termination approach for next-generation ultra-high-voltage SiC devices.

  • Open Access

    Effect of Varying N+ Source Implantation Depth on the Electrical Characteristics of 1.2 kV 4H-SiC MOSFETs

    by Dinuth C.Y.B. Yapa Mudiyanselage, Skylar Deboer, Stephen A. Mancini, Justin Lynch, Seung Yup Jang, Adam J. Morgan, Woongje Sung

    The heavily doped N+ source region in 4H-SiC MOSFETs is a critical design parameter, as its depth and the profile strongly influence contact resistivity and conduction efficiency. This work investigates the impact of varying N+ implantation depth on the electrical performances of 1.2 kV MOSFETs in both Nominal (linear cell) and Hexagonal (HEXFET) architectures. By varying implantation energy at a fixed dose, three junction depths were obtained: 0.22 µm (shallow), 0.24 µm (moderate), and 0.27 µm (deep). Transfer Length Method (TLM) measurements revealed a significant reduction in source contact resistivity with increasing depth, from 3.91×10⁻ 5 Ω·cm² (shallow) to 1.22×10⁻ 6 Ω·cm² (deep). For Nominal MOSFET design, electrical measurements confirmed a corresponding decrease in specific on-resistance (R on,sp ), from 3.05 to 2.89 mΩ·cm². However, deeper implants introduced greater lateral straggle, shortening the effective channel length and reducing the threshold voltage (V th ) from 2.25 V to 1.96 V. The channel barrier potential lowering associated with lateral straggle increased leakage current in the blocking mode, resulting in reduced breakdown voltage (BV). For Nominal MOSFETs, BV decreased from 1610 V in the shallow split to 1470 V in the deep split, while HEXFETs exhibited sharper BV degradation due to their higher channel density. To address this limitation, optimized JFET doping was introduced, restoring the BV of the deep split to 1560 V in the Nominal architecture. These results demonstrate that although increased N+ depth improves conduction by lowering contact resistance, careful co-optimization with P-well and JFET design is necessary to suppress high leakage current during blocking mode.

  • Open Access

    Device Performance and Reliability of SiC CMOS up to 400°C

    by Emran K. Ashik, Sundar B. Isukapati, Hua Zhang, Tian Shi Liu, Utsav Gupta, Adam J. Morgan, Veena Misra, Woong Je Sung, Ayman Fayed, Anant K. Agarwal, et al.

    This study evaluates the performance and reliability of SiC n-and p-MOSFETs across a temperature range from room temperature up to 400°C, focusing on field effect (FE) mobility and threshold voltage variations under high thermal and bias stress conditions. By analyzing the variations in field effect mobility and threshold voltage under different stress conditions, our study illustrates distinct behaviors between devices with thermally grown oxides and those with chemical vapor deposited (CVD) oxide layers, underscoring significant differences in long term performance. Results indicate that while n-MOSFETs maintain threshold voltage shifts below 3% and exhibit robust characteristics up to 400°C, p-MOSFETs exhibit permanent threshold voltage shifts of up to 10% and mobility reductions of 15% particularly above 300°C DC stress. The 2 nm ultrathin thermal (UT) followed by 40nm CVD SiO2, outperform thermal oxides, sustaining less degradation in mobility and less shift in threshold voltage under bias temperature instability (BTI) conditions at voltages up to ±25V and temperatures as high as 400°C. This research advances SiC CMOS technology by confirming that SiC n-MOSFETs are ready for high-temperature circuit applications, while highlighting the need for further improvement in p-MOSFETs to enhance their reliability under extreme conditions.

  • Open Access

    Exploring the Influence of Implant Profile and Device Design on Basal Plane Dislocation Generation in 1.2kV 4H-SiC Power MOSFETs

    by Stephen A. Mancini, Seung Yup Jang, Ze Yu Chen, Balaji Raghothamachar, Michael Dudley, Woong Je Sung

    Several 1.2kV 4H-SiC devices of various cell architectures have been successfully fabricated by employing different P+ implantation conditions, resulting in varying levels of Basal Plane Dislocation (BPD) densities across the different device designs. It was found that by utilizing devices designed with an orthogonal P+ source layout as opposed to the traditional P+ stripe pattern, the long-term reliability under sustained 3rd Quadrant current stress conduction can be greatly improved even in devices with medium BPD densities. In addition, the use of the unipolar current of the JBSFET can further enhance long-term reliability under sustained 3rd Quadrant current stress by mitigating stacking fault expansion, even in devices with a high BPD density.


  • Open Access

    A Novel 'Ladder' Design for Improved Channel Density for 1.2kV 4H-SiC MOSFETs

    by Skylar de Boer, Dinuth C.Y.B. Yapa Mudiyanselage, Seung Yup Jang, Adam Morgan, Woong Je Sung

    A novel topological layout was developed to enhance the channel density of 1.2kV 4H-SiC MOSFETs. The innovative "Ladder" MOSFET incorporates an additional JFET and channel region, arranged orthogonally within the layout. To ensure a fair comparison, identical design rules were applied to both the Nominal and Ladder MOSFETs, resulting in calculated channel densities of 0.30 and 0.41, respectively. Comparative analysis was conducted using Synopsys Sentaurus TCAD simulations, where three dimensional (3D) structures for both designs were generated under the same implantation and process conditions, followed by simulations of static electrical characteristics. The results indicate that the Ladder MOSFET achieved approximately 10% reduction in specific on-resistance (Ron,sp) compared to the Nominal MOSFET. Both MOSFET designs were subsequently fabricated, packaged, and evaluated, with the Ladder MOSFET demonstrating a 12.94% reduction in Ron,sp when comparing the best-performing devices from each design.

  • Open Access

    Optimizing 1.2 kV SiC Trench MOSFETs for Enhanced Performance and Manufacturing Efficiency

    by Seung Yup Jang, Dong Young Kim, Dinuth C.Y.B. Yapa Mudiyanselage, Ho Jung Lee, Chung Kwang Lee, Jin Gon Kim, Dong Kyun Kim, Woong Je Sung

    This paper presents the development and optimization of a 1.2 kV Silicon Carbide (SiC) Trench MOSFET with a Bottom P-well (BPW), designed to achieve a compact structure and a simplified fabrication process. By performing the BPW implant before the trench etching process and utilizing it in conjunction with a shallow trench, the process complexity was reduced while maintaining effective corner coverage of the trench gate. Comprehensive simulations and unit process analyses were conducted to evaluate the effects of the hard mask sidewall angle, P-well, and JFET implant doses on device characteristics. Optimal performance was achieved by introducing an additional P+ implant in the P-well region, which significantly enhanced breakdown voltage without affecting channel properties. The optimized device demonstrated a specific on-resistance (Ron,sp) of 2.2 mΩ·cm2, a breakdown voltage (BV) of 1600 V, and a threshold voltage (Vth) of 3 V, with potential further reductions in Ron,sp through substrate thinning.