Adam J. Morgan
Adam J. Morgan has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Woongje Sung
University at Albany
4 shared publications - Dinuth C.Y.B. Yapa Mudiyanselage
University at Albany, State University of New York
2 shared publications - Seung Yup Jang
University at Albany
2 shared publications - Skylar Deboer
University at Albany
2 shared publications - Stephen A. Mancini
University at Albany
2 shared publications - Anant K. Agarwal
Department of Electrical & Computer Engineering, The Ohio State University, Columbus, OH 43210, USA
1 shared publication
Latest Publications
- Open Access
- 19 May 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1055, 37-44
Comparative Study of 1.2kV 4H-SiC Bi-Directional MOSFET (BiD-MOS) Design Approaches: 2-Chip vs Monolithic Integration
Several 1.2kV 4H-SiC Bi-Directional MOSFETs (BiD-MOS) design approaches were successfully fabricated and evaluated based on their electrical characteristics. Both monolithic integration design approaches exhibited negligible differences in conduction, blocking, and switching characteristics when compared to their 2-Chip counterpart. However, during the short-circuit withstand time testing, severe gate oscillations were observed in the 2-Chip design, which was not an issue present in either monolithic configuration. As a result of its robust electrical behavior, monolithic integration emerges as a promising design approach for developing efficient and reliable Bi-Directional Switches.
- 19 May 2026
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1055, 37-44
Open AccessComparative Study of 1.2kV 4H-SiC Bi-Directional MOSFET (BiD-MOS) Design Approaches: 2-Chip vs Monolithic Integration
Several 1.2kV 4H-SiC Bi-Directional MOSFETs (BiD-MOS) design approaches were successfully fabricated and evaluated based on their electrical characteristics. Both monolithic integration design approaches exhibited negligible differences in conduction, blocking, and switching characteristics when compared to their 2-Chip counterpart. However, during the short-circuit withstand time testing, severe gate oscillations were observed in the 2-Chip design, which was not an issue present in either monolithic configuration. As a result of its robust electrical behavior, monolithic integration emerges as a promising design approach for developing efficient and reliable Bi-Directional Switches.
- Open Access
- 19 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1191, 81-88
Effect of Varying N+ Source Implantation Depth on the Electrical Characteristics of 1.2 kV 4H-SiC MOSFETs
The heavily doped N+ source region in 4H-SiC MOSFETs is a critical design parameter, as its depth and the profile strongly influence contact resistivity and conduction efficiency. This work investigates the impact of varying N+ implantation depth on the electrical performances of 1.2 kV MOSFETs in both Nominal (linear cell) and Hexagonal (HEXFET) architectures. By varying implantation energy at a fixed dose, three junction depths were obtained: 0.22 µm (shallow), 0.24 µm (moderate), and 0.27 µm (deep). Transfer Length Method (TLM) measurements revealed a significant reduction in source contact resistivity with increasing depth, from 3.91×10⁻ 5 Ω·cm² (shallow) to 1.22×10⁻ 6 Ω·cm² (deep). For Nominal MOSFET design, electrical measurements confirmed a corresponding decrease in specific on-resistance (R on,sp ), from 3.05 to 2.89 mΩ·cm². However, deeper implants introduced greater lateral straggle, shortening the effective channel length and reducing the threshold voltage (V th ) from 2.25 V to 1.96 V. The channel barrier potential lowering associated with lateral straggle increased leakage current in the blocking mode, resulting in reduced breakdown voltage (BV). For Nominal MOSFETs, BV decreased from 1610 V in the shallow split to 1470 V in the deep split, while HEXFETs exhibited sharper BV degradation due to their higher channel density. To address this limitation, optimized JFET doping was introduced, restoring the BV of the deep split to 1560 V in the Nominal architecture. These results demonstrate that although increased N+ depth improves conduction by lowering contact resistance, careful co-optimization with P-well and JFET design is necessary to suppress high leakage current during blocking mode.
- 19 May 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1191, 81-88
Open AccessEffect of Varying N+ Source Implantation Depth on the Electrical Characteristics of 1.2 kV 4H-SiC MOSFETs
The heavily doped N+ source region in 4H-SiC MOSFETs is a critical design parameter, as its depth and the profile strongly influence contact resistivity and conduction efficiency. This work investigates the impact of varying N+ implantation depth on the electrical performances of 1.2 kV MOSFETs in both Nominal (linear cell) and Hexagonal (HEXFET) architectures. By varying implantation energy at a fixed dose, three junction depths were obtained: 0.22 µm (shallow), 0.24 µm (moderate), and 0.27 µm (deep). Transfer Length Method (TLM) measurements revealed a significant reduction in source contact resistivity with increasing depth, from 3.91×10⁻ 5 Ω·cm² (shallow) to 1.22×10⁻ 6 Ω·cm² (deep). For Nominal MOSFET design, electrical measurements confirmed a corresponding decrease in specific on-resistance (R on,sp ), from 3.05 to 2.89 mΩ·cm². However, deeper implants introduced greater lateral straggle, shortening the effective channel length and reducing the threshold voltage (V th ) from 2.25 V to 1.96 V. The channel barrier potential lowering associated with lateral straggle increased leakage current in the blocking mode, resulting in reduced breakdown voltage (BV). For Nominal MOSFETs, BV decreased from 1610 V in the shallow split to 1470 V in the deep split, while HEXFETs exhibited sharper BV degradation due to their higher channel density. To address this limitation, optimized JFET doping was introduced, restoring the BV of the deep split to 1560 V in the Nominal architecture. These results demonstrate that although increased N+ depth improves conduction by lowering contact resistance, careful co-optimization with P-well and JFET design is necessary to suppress high leakage current during blocking mode.
- Open Access
- 12 September 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1024, 57-64
Device Performance and Reliability of SiC CMOS up to 400°C
This study evaluates the performance and reliability of SiC n-and p-MOSFETs across a temperature range from room temperature up to 400°C, focusing on field effect (FE) mobility and threshold voltage variations under high thermal and bias stress conditions. By analyzing the variations in field effect mobility and threshold voltage under different stress conditions, our study illustrates distinct behaviors between devices with thermally grown oxides and those with chemical vapor deposited (CVD) oxide layers, underscoring significant differences in long term performance. Results indicate that while n-MOSFETs maintain threshold voltage shifts below 3% and exhibit robust characteristics up to 400°C, p-MOSFETs exhibit permanent threshold voltage shifts of up to 10% and mobility reductions of 15% particularly above 300°C DC stress. The 2 nm ultrathin thermal (UT) followed by 40nm CVD SiO2, outperform thermal oxides, sustaining less degradation in mobility and less shift in threshold voltage under bias temperature instability (BTI) conditions at voltages up to ±25V and temperatures as high as 400°C. This research advances SiC CMOS technology by confirming that SiC n-MOSFETs are ready for high-temperature circuit applications, while highlighting the need for further improvement in p-MOSFETs to enhance their reliability under extreme conditions.
- 12 September 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1024, 57-64
Open AccessDevice Performance and Reliability of SiC CMOS up to 400°C
This study evaluates the performance and reliability of SiC n-and p-MOSFETs across a temperature range from room temperature up to 400°C, focusing on field effect (FE) mobility and threshold voltage variations under high thermal and bias stress conditions. By analyzing the variations in field effect mobility and threshold voltage under different stress conditions, our study illustrates distinct behaviors between devices with thermally grown oxides and those with chemical vapor deposited (CVD) oxide layers, underscoring significant differences in long term performance. Results indicate that while n-MOSFETs maintain threshold voltage shifts below 3% and exhibit robust characteristics up to 400°C, p-MOSFETs exhibit permanent threshold voltage shifts of up to 10% and mobility reductions of 15% particularly above 300°C DC stress. The 2 nm ultrathin thermal (UT) followed by 40nm CVD SiO2, outperform thermal oxides, sustaining less degradation in mobility and less shift in threshold voltage under bias temperature instability (BTI) conditions at voltages up to ±25V and temperatures as high as 400°C. This research advances SiC CMOS technology by confirming that SiC n-MOSFETs are ready for high-temperature circuit applications, while highlighting the need for further improvement in p-MOSFETs to enhance their reliability under extreme conditions.
- Open Access
- 10 September 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1023, 21-27
A Novel 'Ladder' Design for Improved Channel Density for 1.2kV 4H-SiC MOSFETs
A novel topological layout was developed to enhance the channel density of 1.2kV 4H-SiC MOSFETs. The innovative "Ladder" MOSFET incorporates an additional JFET and channel region, arranged orthogonally within the layout. To ensure a fair comparison, identical design rules were applied to both the Nominal and Ladder MOSFETs, resulting in calculated channel densities of 0.30 and 0.41, respectively. Comparative analysis was conducted using Synopsys Sentaurus TCAD simulations, where three dimensional (3D) structures for both designs were generated under the same implantation and process conditions, followed by simulations of static electrical characteristics. The results indicate that the Ladder MOSFET achieved approximately 10% reduction in specific on-resistance (Ron,sp) compared to the Nominal MOSFET. Both MOSFET designs were subsequently fabricated, packaged, and evaluated, with the Ladder MOSFET demonstrating a 12.94% reduction in Ron,sp when comparing the best-performing devices from each design.
- 10 September 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1023, 21-27
Open AccessA Novel 'Ladder' Design for Improved Channel Density for 1.2kV 4H-SiC MOSFETs
A novel topological layout was developed to enhance the channel density of 1.2kV 4H-SiC MOSFETs. The innovative "Ladder" MOSFET incorporates an additional JFET and channel region, arranged orthogonally within the layout. To ensure a fair comparison, identical design rules were applied to both the Nominal and Ladder MOSFETs, resulting in calculated channel densities of 0.30 and 0.41, respectively. Comparative analysis was conducted using Synopsys Sentaurus TCAD simulations, where three dimensional (3D) structures for both designs were generated under the same implantation and process conditions, followed by simulations of static electrical characteristics. The results indicate that the Ladder MOSFET achieved approximately 10% reduction in specific on-resistance (Ron,sp) compared to the Nominal MOSFET. Both MOSFET designs were subsequently fabricated, packaged, and evaluated, with the Ladder MOSFET demonstrating a 12.94% reduction in Ron,sp when comparing the best-performing devices from each design.