VBValentyn Barannik

Valentyn Barannik

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Valentyn Barannik has a total of 4 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development a computationally efficient method to solve direct and inverse aerodynamic problems related to turbomachines

    by Valery Subotovich, Oleksandr Yudin, Artem Babaiev, Valentyn Barannik, Olena Avdieieva

    This study investigates aerodynamic processes in interblade, axial annular, and radial-axial channels in turbomachines. The task addressed relates to the need to improve the computational efficiency in solving direct and inverse aerodynamic problems when analyzing and designing flow parts of turbomachines. A computationally efficient method for solving direct and inverse aerodynamic problems has been proposed, which provides acceptable accuracy for engineering practice at significantly lower computational costs compared to conventional CFD approaches. The results include a devised single mathematical formulation based on Euler equations for a compressible fluid, written in terms of the flow function. The proposed method makes it possible to consider direct and inverse problems within a common mathematical structure. The system of equations is reduced to a single differential equation and a set of algebraic relations while the global flow problem is decomposed into a set of independent problems for individual cross-sections. The inverse problem is stated as a nonlinear optimization problem based on the mass flow rate agreement condition derived from the energy equation. The computational complexity is reduced by using the flow function and the decomposition of the computational domain. The method combines the capabilities of direct analysis and reconstruction of the flow channel geometry based on the predefined aerodynamic characteristics. Verification by experimental data and direct calculation results demonstrated good agreement between the velocity distributions and the reconstructed geometry; the maximum deviations did not exceed 0.3%. The results could be practically applied to preliminary design, parametric optimization, as well as inverse design of the flow parts in turbomachines

  • Open Access

    Evaluation of Methods for Predicting Deviation Angle in Planar Turbine Cascades

    by Artem Babaiev, Olexander Yudin, Valentyn Barannik, Olena Avdieieva

    This paper presents a review of methods for predicting the flow exit angle from a planar turbine cascade operating with subsonic and transonic flow regimes. An analysis of empirical correlations used to determine the deviation angle is performed, and the advantages and limitations of each approach are discussed. The accuracy of empirical correlations and the CFD approach is evaluated by comparing their predictions with experimental data obtained for the VKI turbine cascade profile under both design and off-design operating conditions. The comparison reveals a low prediction accuracy of empirical correlations for considered regimes. The largest discrepancies are observed at outlet Mach numbers below 0.6. The closest agreement with experimental data is achieved using CFD (AxCFD™). The results show good consistency both in terms of the absolute values of the deviation angle and the trend of its variation under off-design conditions. Additional CFD simulations of three planar turbine cascade configurations demonstrate a significant influence of blade geometry on the predicted deviation angle. The relationship between the kinetic energy loss coefficient and the deviation angle is also discussed. Both CFD and experimental results indicate that the minimum loss condition corresponds to the minimum deviation angle. Furthermore, a consistent trend in the variation of these two parameters is observed across different operating regimes. It is concluded that accurate prediction of the deviation angle is a complex problem requiring consideration of a wide range of geometric and operating parameters of the cascade. Further research in this area is recommended.

  • Design and Operating Modes of Stop and Control Valves of High-Power Steam Turbines

    by Artem Babaiev, Alexander Yudin, Valentyn Barannik, Olena Avdieieva

    The operating modes of stop and control valves of high-pressure and intermediate-pressure (low-pressure) sections of existing steam turbines of thermal and nuclear power plants are discussed in the article. Typical operating modes of the valves are defined depending on their functional purpose within the installation, the steam distribution system, the turbine type, and the method of power control. The flow pattern in angle-type valves with one side steam supply into the steam chest is discussed. It is noted that this design is typical for use in high-power steam turbine units operated in Ukraine. As a result, a classification of stop and control valves into three groups is proposed. For each group, recommendations are provided regarding the design of the valve flow-path elements, specifically the main plug and the seat, which contribute to improving their operational efficiency. In addition, to stabilize the flow, the feasibility of installing a special cylindrical shell inside the steam chest is considered, featuring an impermeable sector oriented toward the valve inlet pipe.