Clisia Aversa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Clisia Aversa has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- António Bastos Pereira
TEMA—Centre for Mechanical Technology and Automation, Department of Mechanical Engineering, University of Aveiro, Campus de Santiago, 3810-193 Aveiro, Portugal
1 shared publication - Basma Ben Difallah
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
1 shared publication - Faten Nasri
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
1 shared publication - Fida Harabi
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
1 shared publication - Massimiliano Barletta
Dipartimento di Ingegneria Industriale, Elettronica e Meccanica, Università degli Studi Roma Tre, Roma, Italy
1 shared publication - Mohamed Kharrat
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
1 shared publication
Latest Publications
- Open Access
- 26 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 100
On the Microstructural and Tribological Investigations of WC-12Co/NiCrFeSiAlBC HVOF Cermet Coatings: Effects of WC-12Co Fraction
Previous research indicates that WC-12Co contents above 60 wt.% in feedstock powders for cermet coatings impair adhesion and wear resistance. This study characterizes NiCrFeSiAlBC coatings—unreinforced or reinforced with 65 wt.% or 85 wt.% WC-12Co—applied via high-velocity oxy-fuel (HVOF) spraying onto stainless steel substrates under controlled parameters. It quantifies the influence of high carbide volume fractions within the NiCrFeSiAlBC matrix on microstructure and tribomechanical performance. Microstructural analysis revealed uniformly distributed cermet layers featuring dissolved reinforcements and WC hard phase formation, with minimal W2C crystallization. Elevated WC-12Co incorporation promoted densification and reduced porosity. Vickers microhardness tests (HV 0.3) demonstrated increased hardness upon WC-12Co addition, attributable to finer particle sizes, lower porosity, and the presence of WC phases alongside crystallographic refinements. Under dry reciprocating sliding conditions, friction coefficients and wear volumes decreased markedly. Consequently, the coating with 85 wt.% WC exhibited the best mechanical and tribological properties.
- 26 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 100
Open AccessOn the Microstructural and Tribological Investigations of WC-12Co/NiCrFeSiAlBC HVOF Cermet Coatings: Effects of WC-12Co Fraction
Previous research indicates that WC-12Co contents above 60 wt.% in feedstock powders for cermet coatings impair adhesion and wear resistance. This study characterizes NiCrFeSiAlBC coatings—unreinforced or reinforced with 65 wt.% or 85 wt.% WC-12Co—applied via high-velocity oxy-fuel (HVOF) spraying onto stainless steel substrates under controlled parameters. It quantifies the influence of high carbide volume fractions within the NiCrFeSiAlBC matrix on microstructure and tribomechanical performance. Microstructural analysis revealed uniformly distributed cermet layers featuring dissolved reinforcements and WC hard phase formation, with minimal W2C crystallization. Elevated WC-12Co incorporation promoted densification and reduced porosity. Vickers microhardness tests (HV 0.3) demonstrated increased hardness upon WC-12Co addition, attributable to finer particle sizes, lower porosity, and the presence of WC phases alongside crystallographic refinements. Under dry reciprocating sliding conditions, friction coefficients and wear volumes decreased markedly. Consequently, the coating with 85 wt.% WC exhibited the best mechanical and tribological properties.