Abdullah S. AlOwaysi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Abdullah S. AlOwaysi has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Abdulrahman Alaskar
Department of Chemistry, National Measurement and Calibration Center, Saudi Standards, Metrology and Quality Organization (SASO), Riyadh 11471, Kingdom of Saudi Arabia
2 shared publications - Adel Shehata
Department of Chemistry, National Measurement and Calibration Center, Saudi Standards, Metrology and Quality Organization (SASO), Riyadh 11471, Kingdom of Saudi Arabia
2 shared publications - Najjy Alyami
Saudi Standards Metrology and Quality Org
1 shared publication
Latest Publications
- Open Access
- 9 October 2026
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 38 (10) , 2559-2566
Preparation and Certification of Propane in Nitrogen as Reference Material for Ensuring Traceability of Hydrocarbon Emission Measurements
Propane in nitrogen (C3H8/N2) gas mixtures are widely used as calibration standards for hydrocarbon measurements in environmental monitoring, energy production and industrial process control. Five C3H8/N2 gas mixtures, covering the range of 804.8148-12053.8148 µmol/mol, were gravimetrically prepared according to ISO 6142 using a two-step dilution approach with high-purity propane and nitrogen. The prepared mixtures were validated by gas chromatography with flame ionization detection (GC-FID) in accordance with ISO 6143. The GC-FID results showed good agreement with the gravimetric values, confirming the validity of the preparation method. The certified values determined by gravimetry were established for 4 mixtures (B, C, D, E) as 12053.81 ± 97.49, 9013.23 ± 78.11, 5998.011 ± 57.72 and 2987.29 ± 66.91 µmol/mol, respectively. The mole fraction of the mixture F, 804.81 ± 35.97 µmol/mol was considered an information value since it was associated with large uncertainty of 7.016%. The performance of the produced certified reference materials (CRMs) was checked by using them to calibrate the GC-FID, then measure a CRM sample of 8010 µmol/mol as an unknown. The precision (%RSD) and accuracy of the measured results were found to be 0.12% and 99.75%, respectively. These results confirm that the prepared C3H8/N2 mixtures meet the criteria for certified reference materials and are suitable as calibrants for hydrocarbon emission measurement instruments in industrial gas analysis and environmental monitoring.
- 9 October 2026
- Published by Asian Publication Corporation in Asian Journal of Chemistry
- Vol. 38 (10) , 2559-2566
Open AccessPreparation and Certification of Propane in Nitrogen as Reference Material for Ensuring Traceability of Hydrocarbon Emission Measurements
Propane in nitrogen (C3H8/N2) gas mixtures are widely used as calibration standards for hydrocarbon measurements in environmental monitoring, energy production and industrial process control. Five C3H8/N2 gas mixtures, covering the range of 804.8148-12053.8148 µmol/mol, were gravimetrically prepared according to ISO 6142 using a two-step dilution approach with high-purity propane and nitrogen. The prepared mixtures were validated by gas chromatography with flame ionization detection (GC-FID) in accordance with ISO 6143. The GC-FID results showed good agreement with the gravimetric values, confirming the validity of the preparation method. The certified values determined by gravimetry were established for 4 mixtures (B, C, D, E) as 12053.81 ± 97.49, 9013.23 ± 78.11, 5998.011 ± 57.72 and 2987.29 ± 66.91 µmol/mol, respectively. The mole fraction of the mixture F, 804.81 ± 35.97 µmol/mol was considered an information value since it was associated with large uncertainty of 7.016%. The performance of the produced certified reference materials (CRMs) was checked by using them to calibrate the GC-FID, then measure a CRM sample of 8010 µmol/mol as an unknown. The precision (%RSD) and accuracy of the measured results were found to be 0.12% and 99.75%, respectively. These results confirm that the prepared C3H8/N2 mixtures meet the criteria for certified reference materials and are suitable as calibrants for hydrocarbon emission measurement instruments in industrial gas analysis and environmental monitoring.
- 8 June 2021
- Published by ACG Publications in Journal of Chemical Metrology
- Vol. 15 (1) , 11-24
Preparation and certification of carbon monoxide gas reference material for the quality of CO emission measurements
Carbon monoxide emissions in air are toxic and its monitoring is of great concern worldwide. The monitoring activities should rely on traceable measurement results to the SI units. To serve this monitoring purpose in Saudi Arabia, a primary gas mixture (200 mmol/mol) of Carbon monoxide (CO) in nitrogen has been gravimetrically prepared from pure CO and pure N2 in 5L aluminum gas cylinder based on ISO 6142. From this mixture, three diluted mixtures of concentrations 4.99, 7.49 and 10.01 mmol/mol were prepared also in 5L cylinders and the uncertainty of these gravimetric preparations was calculated. The mole fractions of the three mixtures were verified by GC-TCD in accordance with ISO 6143 and the uncertainty of the chromatographic measurements was calculated. The gravimetrically and chromatographically measured mole fractions together with their standard uncertainties were found compatible indicating good quality of the produced primary gas mixtures. Long term stability of the three gas mixtures was monitored along four years, and the results obtained showed very good stability of the gas mixtures. The relative uncertainty of the GC analytical results was found 0.52%, 0.51% and 0.52% which is small enough and advantageous for the calibration of CO emission measuring equipment.
- 8 June 2021
- Published by ACG Publications in Journal of Chemical Metrology
- Vol. 15 (1) , 11-24
Preparation and certification of carbon monoxide gas reference material for the quality of CO emission measurements
Carbon monoxide emissions in air are toxic and its monitoring is of great concern worldwide. The monitoring activities should rely on traceable measurement results to the SI units. To serve this monitoring purpose in Saudi Arabia, a primary gas mixture (200 mmol/mol) of Carbon monoxide (CO) in nitrogen has been gravimetrically prepared from pure CO and pure N2 in 5L aluminum gas cylinder based on ISO 6142. From this mixture, three diluted mixtures of concentrations 4.99, 7.49 and 10.01 mmol/mol were prepared also in 5L cylinders and the uncertainty of these gravimetric preparations was calculated. The mole fractions of the three mixtures were verified by GC-TCD in accordance with ISO 6143 and the uncertainty of the chromatographic measurements was calculated. The gravimetrically and chromatographically measured mole fractions together with their standard uncertainties were found compatible indicating good quality of the produced primary gas mixtures. Long term stability of the three gas mixtures was monitored along four years, and the results obtained showed very good stability of the gas mixtures. The relative uncertainty of the GC analytical results was found 0.52%, 0.51% and 0.52% which is small enough and advantageous for the calibration of CO emission measuring equipment.