SASaleh Sobhy Abdelhady

Saleh Sobhy Abdelhady

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Saleh Sobhy Abdelhady has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development of hybrid glass fiber/epoxy nanocomposites strengthened with ceramic nanoparticles: mechanical and dynamic mechanical performance

    by Saleh S. Abdelhady, Asmaa M. Kassab, Mohamed Ragab, Shaimaa M. Mohamed

    Composite materials are used in a wide range of contemporary applications. Consequently, the development of high-performance hybrid nanocomposites for advanced engineering applications continues to depend critically on the optimization of nanoparticle content and processing conditions. The present work investigates the significance of incorporating SiO 2 and TiO 2 nanoparticles on an epoxy matrix reinforced with different E-glass fiber layers in terms of its tensile, flexural, impact strength, and dynamic mechanical performance. The mechanical and dynamic mechanical performance of hybrid woven glass fiber/epoxy nanocomposites reinforced with TiO 2 and SiO 2 ceramic nanoparticles was developed and evaluated. Based on results from experiments, the stiffness, toughness, and structural integrity of the composites were considerably improved by increasing the number of woven glass fiber layers from 6 to 9 layers. As the number of fiber layers and nanoparticle incorporation increased, it was found that the mechanical performance improved. The greatest improvement was observed in 0.5 wt% TiO₂-reinforced composites, which achieved a 66% increase in tensile strength (262 MPa) compared with neat 9 layers of glass fiber/epoxy composites (157 MPa). The flexural strength of the nanocomposites increased by 28%, from 309 MPa for nine layers of glass fiber/epoxy composites to 398 MPa. Furthermore, the impact strength of the composites reinforced with TiO₂ nanoparticles (G6T and G9T) was significantly higher than that of the neat and SiO₂-filled composites. E-glass fiber /epoxy laminates with two distinct fiber-layer structures, single and hybrid TiO₂/SiO₂ nanoparticle reinforcements, are compared. The use of SiO₂ or TiO₂ nanoparticles in epoxy composites makes it novel. The combined effect of dual nanoparticle reinforcement led to significant improvements in mechanical and dynamic mechanical properties in hybrid TiO₂/SiO₂ reinforced composites. To improve resistance to crack propagation and boost load transfer capability, ceramic nanoparticles were added to the epoxy matrix and glass fibers to strengthen the interfacial bond.

  • Optimization of electrospun polyamide 6,6/polyvinyl alcohol nanofibril composite through response surface methodology and neural networks

    by Saleh S. Abdelhady, Shaimaa M. Mohamed, Asmaa M. Kassab

    The present investigation employs artificial neural networks (ANN) and response surface methodology (RSM) to model the diameter of a polyamide-6,6 (PA66)/polyvinyl alcohol (PVA) nanofibril composite. For modelling the average diameter of nanofibers, RSM approach based on four parameters (PA66/PVA (wt.%), high voltage (kV), needle tip to collector distance (cm) and flow rate (mL/h)) in five levels was compared to ANN technique. Central composite design (CCD) was employed in the RSM approach to ascertain the individual and combined effects of the parameters on the average diameter of nanofibril composite. The network topology of 4-10-1 has good predictability for analyzing factors impacting PA66/PVA fiber diameter, as demonstrated by the strong correlation between the experimental and predicted PA66/PVA fiber diameters using an artificial neural network. ANN predicts PA66/PVA nanofibril composite diameter with an average absolute relative error of 1.149%, which is marginally lower than RSM’s result of 1.639%. The high regression coefficient between the variables and the response (R 2 = 0.991) shows a good second-order polynomial regression model for evaluating experimental data. The R 2 value was 0.989, indicating that the ANN model was good fit with the experimental results. The RSM model determined optimum conditions for electrospinning PA66/PVA nanofiber that can produce fine, reliable, and high-quality nanofibers: PA66/PVA concentration of 50/50 wt.%, high voltage of 19 kV, needle tip to collector distance of 12 cm, and flow rate of 0.1 mL/h. This investigation is novel in that it uses ANN and RSM to compute and model the effects of electrospinning parameters for increasing nanofiber diameter. The investigation will help practitioners, researchers, and engineers create nanofibers using electrospinning machines, which is the scientific application of this investigation.

  • Open Access

    Tensile performance modeling and process optimization of AA6061-T6/WC surface nanocomposites developed via friction stir processing

    by Saleh S. Abdelhady, Rehab E. Elbadawi

    In the present investigation, friction stir processing (FSP) is implemented to develop the tungsten carbide (WC) nanoparticle-reinforced aluminum alloy Al6061-T6. The tensile properties of the Al6061-T6/WC surface nanocomposite were evaluated in relation to the volume fraction of WC nanoparticles, the number of passes, rotation speed, and traverse speed. The experiments were designed using the Box-Behnken Design (BBD) of response surface methodology (RSM). For identifying the significant variables and interaction implications, analysis of variance (ANOVA) was performed. The models generated demonstrate that rotating speed is the most significant variable and transverse speed is of little importance. Heat input to FSP increases as traverse speed decreases and tool rotational speed increases. Increasing the number of FSP passes effectively broke the coarse and dendritic clusters, refined the matrix grains, and dynamic recrystallization (DRX) resulting in equiaxed grains that, through restricted dislocation activity, exhibit tensile behavior. Furthermore, the extreme plastic deformation and heat production during FSP results in the breakage of WC particles and coarse particles, the removal of porous holes, and DRX of an ultrafine grain-sized structure. The optimized surface nanocomposite with the highest tensile strength (315 MPa), yield strength (221 MPa), and elongation (9.7%) was achieved at volume fraction 2%, number of passes 5, rotation speed 1000 rpm, and traverse speed 30 mm/min. The surface composite that developed has been identified as an appropriate material for the automotive, aerospace, marine, defense, and transportation sectors, among others, that require lightweight and improved surface qualities.


  • Open Access

    Enhancement of Epoxy-derived Polymer Nanocomposites Strengthened with Titanium Dioxide (TiO2) and Silicon Oxide (SiO2) Nanoparticles

    by Saleh S. Abdelhady, Said H. Zoalfakar, Rehab E. Elbadawi, Shaimaa M. Mohamed

    This work investigates the mechanical characteristics of epoxy nanocomposites reinforced with titanium dioxide (TiO 2 ) and silicon oxide (SiO 2 ) nanoparticles. The intrinsic brittleness and low impact resistance of neat epoxy resin limit its use in high-performance settings, despite its benefits, which include high stiffness, chemical stability, and thermal resistance. The inclusion of nano-sized reinforcements was investigated as a solution to these constraints, with the objective of improving the impact, tensile, flexural, and compressive qualities of epoxy-based composites. The presence of nanoparticles significantly improved all tested properties, according to mechanical characterization. The tensile strength of the nanocomposites increased from 67 MPa for pure epoxy to 84 MPa for the composite that contained 2 wt.% TiO 2 and 1 wt.% SiO 2 . The flexural strength of the nanocomposites increased by 242.5% (from 73 MPa for pure epoxy to 250 MPa for the composite). The compressive strength and strain tolerance of all nanocomposite samples have significantly improved, and stress increases nearly monotonically with strain. This enhancement is ascribed to improved interfacial bonding between the nanoparticles and matrix, which promoted energy dissipation during fracture. Improved interfacial bonding and particle dispersion in low to moderately filled systems were confirmed by morphological analysis using SEM and EDX, which also showed uniform distribution and little void formation. These improved epoxy nanocomposites are especially well-suited for structural uses in the automotive, marine, and aerospace industries where durability and high strength-to-weight ratios are crucial. They are also perfect for protective coatings and electronic encapsulants in harsh environments due to their enhanced impact resistance and surface hardness.


  • Modeling of wear performance and surface roughness of AA6061-T6/B 4 C composite under dry sliding conditions by RSM

    by Saleh S Abdelhady, Ahmed Nabhan, Said H Zoalfakar, Rehab E Elbadawi

    The present study is an attempt to investigate the tribological behavior of friction stir processing (FSP) AA6061-T6 alloy reinforced with boron carbide (B4C) particles. The surface composites were developed to investigate wear performance and surface roughness under dry sliding conditions. The experiments were conducted using response surface methodology (RSM) to examine the effects of various B4C volume fractions, applied loads, and sliding distances. All combinations of reinforcements in AA6061-T6 hybrid composites show a good improvement in the wear properties. The results show that the wear behavior of composites is significantly impacted by the incorporation of B4C particles. This is mostly owing to the uniformity that the B4C particles developed when they distributed the reinforcements evenly in the AA 6061-T6 matrix. Analysis of variance, main effect and three-dimensional plots were used to quantify the effects of dry sliding parameters on tribological properties. The findings showed that the optimal parameters for the effective reduction of specific wear rate and coefficient of friction were a volume fraction of 10%, an applied load of 20 N, and a sliding distance of 500 m. To minimize surface roughness, the optimal test conditions were found to be 10% volume fraction, 40 N applied load, and 2500 m sliding distance. The wear surface was analyzed using energy dispersive spectroscopy (EDX) and scanning electron microscopy (SEM). The results showed that oxide layer formation was present on the wear surface and adhesive wear was the primary wear mechanism.


  • Central Composite Design and Response Surface Methodology for Optimizing the Diameter of Electrospun Polyamide-6,6 Nanofiber Mat

    by Saleh S. Abdelhady, Ashraf A. Ali, Said H. Zoalfakar, Rehab E. Elbadawi

    Electrospinning is a well-established technique for creating submicron polymer fibers to create distinctive functional nanostructures. Electrospinning parameters including solution concentration, tip-to-collector distance and applied voltage are adjusted to produce nonwovens with variable fiber diameter distributions. This research on the response surface methodology (RSM) is being used to model the diameter of a polyamide-6,6 (PA-6,6) nanofiber mat. The experiments were designed using central composite design (CCD) and RSM, which evaluated the interactions between the operating variables (polymer concentration, applied positive voltage, needle tip to collector distance and spinning angle) on the diameter of the PA-6,6 nanofiber. The average nanofiber diameter increased as the concentration of the PA-6,6 polymer solution increased. The model’s strong regression coefficient ([ ]) reveals that it did a desirable of predicting the diameter of PA-6,6 fibers. The experimental findings and predicted fiber diameters were in good agreement. The results demonstrate that the optimization of electrospinning process to produce the smallest nanofibers and narrowest diameter distribution ([ ]) combined effects of 10% polymer concentration, 21[ ]kV applied positive voltage, 18[ ]cm needle tip to collector distance and [ ] spinning angle are substantial interacting effects that have an impact on the surface response nanofibers. The results of the research and several mathematical models will offer useful guidelines for choosing parameter settings for electrospinning PA-6,6 to achieve the required fiber diameter. By saving time, effort and money more effectively, this research will expand the field of investigation for the quality of electrospun nanofibers.


  • Open Access

    Multi-objective optimization of FSW variables on joint properties of AA5754 aluminum alloy using Taguchi approach and grey relational analysis

    by Saleh S. Abdelhady, Rehab E. Elbadawi, Said H. Zoalfakar

    Friction stir welding (FSW) processing of the joint is a technique to improve the quality of the weld. The present research employed the friction stir welding technique to butt-weld AA5754 plates, whereby the joints of every weld case were identified based on their tensile strength, hardness, and impact toughness. The plates were joined by varying the rotational speeds, welding speeds, and tool tilt angles. A multi-objective optimization Taguchi’s design of experiments approach and grey relational analysis (GRA) were used in this study to assess the combined effects of the process variables. The developed models are evaluated for sufficiency, and then the most significant parameters are determined using the analysis of variance (ANOVA). The results of the ANOVA showed that the rotational speed has a maximum contribution of 55.24%, 59%, and 46.27% in obtaining the optimal values of tensile strength, hardness, and impact toughness, respectively. It was found that formability and mechanical behaviors increased with increasing tilt angle for the tilt angle range examined in the current study. The two methods provide the same results, and the optimal conditions are a rotational speed of 1000 rpm, a welding speed of 60 mm/min, and a tilt angle of 2.5°. The optimal values for tensile strength, hardness, and impact toughness, respectively, were found to be 136 MPa, 85.25 HV, and 13 J. Significant implications for the welding industry may arise from the highly favorable outcomes in terms of microstructure and mechanical attributes.


  • Open Access

    Multi-objective optimization of FSW variables on joint properties of AA5754 aluminum alloy using Taguchi approach and grey relational analysis

    by Saleh Sobhy, Rehab E Elbadawi, Said Zoalfakar

    The friction stir welding (FSW) process was applied to butt-weld AA5754 plates, and the joints of each weld case were identified by their tensile strength, hardness, and impact toughness. The combined effects of the process variables rotation speed, welding speed, and tilt angle have been evaluated in the present study using Taguchi's design of experiments approach and grey relational analysis (GRA). A multi-objective optimization approach (Taguchi method and GRA) was used to optimize and rank the process variables. The developed models are evaluated for sufficiency, and the most significant terms are found using the ANOVA approach. The results of the ANOVA showed that the rotational speed has a maximum contribution of 55.24%, 59%, and 46.27% in obtaining the optimal values of tensile strength, hardness, and impact toughness, respectively. Finding an optimal parameter that offers the maximum value of all replies requires the use of the GRA and Taguchi Technique by Similarity to Suitable Solution. The two methods provide the same results, and the optimal conditions are a rotational speed of 1000 rpm, a welding speed of 60 mm/min, and a tilt angle of 2.5 degrees. The optimal values for tensile strength, hardness, and impact toughness, respectively, were found to be 136 MPa, 85.25 HV, and 13 J.


  • Optimization of electrospun chitosan/polyethylene oxide hybrid nanofibril composite via response surface methodology

    by Saleh S Abdelhady, Ar El-Desouky, Amf Kassab, Waleed Barakat, Said H Zoalfakar

    The present study is an attempt to optimize the electrospinning parameters to fabricate chitosan/polyethylene oxide hybrid nanofiber composite with minimum diameter and coefficient of variation (homogeneity) by using response surface methodology (RSM). Based on central composite design (CCD), four factors (the chitosan/PEO ratio, the applied voltage, the needle-to-collector distance, and the spinning angle) was applied to evaluate the individual and combined effects of the parameters on the average diameter of nanofibers. Chitosan (CH) was blended with Polyethylene oxide (PEO) at weight ratios of 1:1, 2:1, 3:1, 4:1, and 5:1. As the composition ratio of chitosan was reduced, the viscosity of the chitosan/PEO blend solution also dropped. The RSM model identified the following conditions as necessary to produce the desired and most uniform CS/PEO fiber diameter: a CS/PEO blend ratio of 2:1 (w/w), a voltage of 25 kV, a distance of 20 cm, and a spinning angle of 45°. The average nanofiber diameter and homogeneity under these conditions were calculated to be 73 nm and 20.5%, respectively, compared to the predicted values of 71 nm and 15.58%, respectively.