Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yixin Bai has a total of 30 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Resin Precursor Solid Content on the Properties of Fiber-Reinforced Phenolic-Resin Aerogel Composites

    by Yixin Bai, Kaiqiang Song, Xuan Wang, Lei Yu, Anwei Huang, Jianchao Huang, Qingbing He, Dong Peng, Min Zhang, Zhongsheng Li

    Lightweight fiber-reinforced phenolic-resin aerogel (NF/PRA) composites are key ablation thermal protection materials for hypersonic vehicles. However, how resin precursor solid content governs the complete processing–structure–property chain, particularly the multi-mode mechanical behavior and high-heat-flux ablation performance, remains poorly understood. In this study, high-silica fiber/phenolic-resin aerogel composites with different contents of a novolac resin precursor (15%, H15S15; 20%, H15S20; 25%, H15S25; 30%, H15S30) were fabricated via vacuum-assisted resin transfer molding combined with atmospheric-pressure drying, and were systematically characterized in terms of their microstructure, mechanical properties, thermophysical behavior, thermal insulation, and ablation resistance. A higher solid content created a denser three-dimensional nano-network in the PRA matrix, decreasing the average pore size from 75.4 to 37.4 nm and increasing the bulk density from 0.299 to 0.458 g/cm3. The abundant mesopores led to ultra-low thermal conductivities of 0.039–0.042 W/(m·K). The compressive, flexural, and shear strengths increased monotonically with the solid content, whereas the tensile strength peaked at 18.03 MPa for H15S25 and declined at higher contents owing to matrix brittleness. Notably, a higher solid content synergistically enhanced both thermal insulation and ablation resistance. After oxyacetylene flame ablation, the linear ablation rate of H15S30 was 32.7% lower than that of H15S15, and the back-face temperature was more than 58% lower. Post-ablation microstructural observations revealed a three-stage mechanism involving pyrolytic carbonization, fiber melting, and mechanical scouring, in which layer-by-layer spallation of the amorphous carbon and SiO2-rich molten phases governs the damage. This study provides guidance for optimizing the processing–structure–property relationship of NF/PRA composites for ablation thermal protection applications.

  • Open Access

    Correction: Li et al. Study on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment. Coatings 2022, 12, 1611

    by Zhongsheng Li, Hulin Wu, Yixin Bai, Dalong Cong, Anwei Huang, Kaiqiang Song, Min Zhang, Zixiang Wei, Xingxing Ding, Xuan Wang, et al.

  • Study on the Wear and Corrosion Resistance of CoCrFeNiTi0.8-xcBN Laser Cladding Coatings

    by Zhongsheng Li, Kaiqiang Song, Yixin Bai, Dalong Cong, Min Zhang, Dong Peng, Xuan Wang, Xingxing Ding, Miaomiao Liao, Fu Zhou, et al.


  • Open Access

    Study on Damage Behavior of NiCoCrAlY/MSZ Plasma-Sprayed Coating in Neutral Salt Spray Environment

    by Zhongsheng Li, Hulin Wu, Yixin Bai, Dalong Cong, Anwei Huang, Kaiqiang Song, Min Zhang, Zixiang Wei, Xingxing Ding, Xuan Wang, et al.

    In order to explore the corrosion damage behavior of plasma-sprayed NiCoCrAlY/magnesia-stabilized zirconia (18~22 wt.% MgO-ZrO2, MSZ) thermal barrier and anti-ablation coatings in a salt spray environment, a series of neutral salt spray (NSS) tests for 96 h (N-2), 192 h (N-4) and 288 h (N-6) were carried out on the coatings. The microstructures, composition distributions, potentiodynamic polarization curves, bonding strengths and anti-ablation properties of the coatings before and after the NSS tests were characterized. The results show that, with the increase in salt spray time, the expansion and overflow of corrosion products (FexOy) led to more defects forming inside the coating; the porosity of the top coat (TC) of N-6 increased to 15.2% in comparison to that of the blank control sample (N-0), which was 8.5%. According to the potentiodynamic polarization curves, accelerated corrosion occurred in the coating samples after the salt spray time reached 192 h, and the corrosion current density rapidly surged from 2.2 × 10−8 A·cm−2 (N-4) to 2.2 × 10−5 A·cm−2 (N-6). Similar degradation tends could be found in the bonding strengths and mass ablation rates of the coatings due to the accumulation of loose corrosion products on the substrate, which affected the bonding states of the coatings and promoted their spalling under an oxyacetylene flame (OAF). As a result, the maximum service life of the NiCoCrAlY/MSZ coatings in the neutral salt spray environment was about 192 h. This work is instructive for studying the environmental adaptability of metal/ceramic double-layer coatings.


  • Open Access

    Mirror-like Bright Al-Mn Coatings Electrodeposition from 1-Ethyl-3 Methylimidazolium Chloride-AlCl3-MnCl2 Ionic Liquids with Pyridine Derivatives

    by Dong Peng, Dalong Cong, Kaiqiang Song, Xingxing Ding, Xuan Wang, Yixin Bai, Xinrui Yang, Changqing Yin, Yuxin Zhang, Jinsong Rao, et al.

    The effects of three pyridine derivative additives, 4-hydroxypyridine, 4-picolinic acid, and 4-cyanopyridine, on Al-Mn coatings were investigated in 1-ethyl-3-methylimidazolium chloride-AlCl3-MnCl2 (EMIC-AlCl3-MnCl2) ionic liquids. The smooth mirror-like bright Al-Mn coatings were obtained only in the EMIC-AlCl3-MnCl2 ionic liquids containing 4-cyanopyridine, while the matte Al-Mn coatings were electrodeposited from EMIC-AlCl3-MnCl2 without additives or containing either 4-hydroxypyridine or 4-picolinic acid. The scanning electron microscope and X-ray diffraction showed that the bright Al-Mn coatings consisted of nanocrystals and had a strong (200) preferential orientation, while the particle size of matte Al-Mn coatings were within the micron range. The brightening mechanism of 4-cyanopyridine is due to it being adsorbed onto the cathode to produce the combined effect of (1) generating an overpotential to promote Al-Mn nucleation; (2) inhibiting the growth of the deposited nuclei and enabling them grow preferentially, making the coating composed of nanocrystals and with a smooth surface. The brightening effect of 4-cyanopyridine on the Al-Mn coatings was far better than that of the 4-hydroxypyridine and the 4-picolinic acid. In addition, the bright Al-Mn coating was prepared in a bath with 6 mmol·L−1 4-cyanopyridine and displayed superior corrosion resistance relative to the matte coatings, which could be attributed to its unique nanocrystalline structure that increased the number of grain boundaries and accelerated the formation of the protective layer of the corrosion products.