HLHye Min Lee

Hye Min Lee

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Hye Min Lee has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Bonding Property of Flip-Chip Chip-Scale Package with Vacuum Reflow and Thermal Compression Bonding Processes

    by So-Hee Hyun, Hye Min Lee, Mi-Song Kim, Won Sik Hong

    The package-on-package technology has been developed to facilitate high-density integration of semiconductor packaging. As the solder bump pitch is decreased, the void content in solder bump joints increases, thereby decreasing its reliability. Consequently, vacuum reflow (VR) is used to increase void fluidity and decrease void content in micro bump joints. Generally, silicon chips in application processor modules are bonded using thermal compression (TC) bonding, followed by the attachment of passive components through hot air reflow soldering. However, the simultaneous bonding of Si chips and passive components using VR can improve productivity.In this study, we performed TC and VR bonding without additional solder pastes, between an Si chip with a Cu pillar/Sn-2.5Ag bump and a bismaleimide triazine substrate plated with electroless-nickel electroless-palladium immersion-gold. It was observed that the void content at the Si chip solder joints yielded by VR (10.8%) was similar to that yielded by TC (11.2%). Furthermore, the Si chip solder joint of the VR sample was thicker than that of the TC sample. This process also resulted in the formation of the intermetallic compounds Cu6Sn5, (Cu,Ni)6Sn5, Ag3Sn, and Ni3P, at the Si chip solder joints. The results of this study suggest that co-bonding of active and passive components is possible through VR soldering for semiconductor packaging.


  • Open Access

    Bonding Property of Middle Temperature Sn-Ag-Cu Solder Ball Joint of Ball Grid Array Package

    by Joo Young Bae, Mi-Song Kim, Hye Min Lee, Seul Gi Lee, Young-Woo Lee, Jeong Tak Moon, Won Sik Hong

    Alloying effects of Nickel and Bismuth in SAC solder to achieve mechanical and microstructural evolution were investigated by comparing three different chemical composition of solders. Sn-3.0Ag-0.5Cu (SAC305) is the most commonly used for Pb-free solder and solder balls are based on Sn-Ag-Cu alloy composition. Compositions of solder balls were Sn-3.0Ag-0.5Cu (SAC305), Sn-1.2Ag-0.5Cu-0.05Ni (SAC1205N) and Sn-Ag-Cu-Ni-Bi based solder (SACNB). Organic solderability preservative (OSP) surface finished substrate, ball grid array (BGA) package arranged by 300 ㎛ diameter solder ball and Type 4 solder paste were used. Solder ball shear test of the BGA package was conducted before the reflow soldering. Board level package bonding process was carried out by hot air reflow soldering. Void content of the BGA solder joint was investigated after soldering. The microstructure evolution before and after thermal cycle test (TCT) was observed using scanning eletron microscopy (SEM) and energy dispersive spectroscopy (EDS). After TCT, intermetallic compound (IMC) refinement and solid solution strengthening effects of Bi element addition were observed in the solder matrix, and also any segregation of Bi element was not founded. Based on these result, it was found that the solder joint reliability of the middle and low temperature solder joints was improved.


  • Open Access

    Solder Joint Degradation and Electrochemical Metallic Ion Migration Property of Solder Joints with Surface Finish

    by Hye Min Lee, Mi-Song Kim, Won Sik Hong

    To confirm the degradation property of solder joints by substrate surface finish, chip resistors are reflow soldered to organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG) finish substrate in a nitrogen atmosphere using the type 6 Sn-3.0Ag-0.5Cu (SAC305) solder paste. To confirm the electrochemical metallic ion migration (ECM) sensitivity with and without photo solder resist (PSR) ink-coated printed circuit board (PCB), comb patterned test vehicles were prepared by the hot air reflow soldering process in nitrogen atmosphere, and the SAC305 solder paste was printed on the conductor of the ECM test PCB. The ECM test was conducted under high temperature and high humidity conditions of 85℃ and 85% RH, respectively. As a result of measuring the void content of the 2012 chip resistor, the average void content of the OSP substrate was higher than that of the ENIG substrate. The thermal shock test (TST) indicated that the degradation rate of the OSP substrate was higher than that of the ENIG substrate. Microstructure analysis showed that the OSP substrate had more crack propagation and thicker intermetallic compound (IMC) thickness than the ENIG substrate. The ECM test revealed that the substrate with PSR-coated PCB coupon generated more dendrites than that without PSR-coated coupon. Because the PSR coated substrate decreased the moisture absorption into the substrate, moredendritesweredeterminedtobe generated.


  • Open Access

    Effects of Solder Powder Particle Size and Substrate Surface Finish on Degradation Properties of Solder Joints

    by Mi-Song Kim, Won Sik Hong, Hye-Min Lee, Myeongin Kim

    In this study, the degradation characteristics of solder joints composed of powder-size Sn-3.0Ag-0.5Cu and the substrate surface finish are compared. Reflow is performed at a N2 ambient to apply an organic solderability preservative (OSP), electroless nickel/immersion gold (ENIG) substrates, and solder pastes of Type 6 (5-15 ㎛) and Type 7 (2-11 ㎛). Subsequently, a thermal shock test (TST) is performed for 1,500 cycles at a temperature of -40 ℃ to 125 ℃ (dwell time of 10 min) to analyze the deterioration characteristics. After N2 reflow is performed, the void content of the OSP substrate/solder joints is higher than that of the ENIG substrate/solder joints, and the shear strength of the ENIG substrate/solder joints is higher than that of the OSP substrate/solder joints. After 500 TST cycles, the shear strength at the OSP substrate/Type 7 solder joints does not decrease, whereas the shear strength at the ENIG substrate/Type 7 solder joints decreases by approximately 25%. Cross-sectional analysis shows that Cu6Sn5 and (Ni,Cu)3Sn4 intermetallic compounds (IMCs) emerged in the OSP and ENIG interfaces, respectively. The increasing rate of IMC thickness at the Type 7 solder joints is higher than that at the Type 6 solder joints. Fracture analysis shows that the OSP and ENIG joints fractured in the solder and solder/IMC interfaces, respectively. The IMC of the OSP and ENIG joints exhibit scallop and needle shapes, respectively. The ENIG joints fractured at the solder/IMC interface because of a stress concentration in the needle-type IMC. After 1500 TST cycles, the shear strength of all samples decreases by more than 50%. Cross-sectional analysis shows a crack at the solder joints of all samples after 1,000 cycles. The decrease in shear strength is caused by these cracks.


  • Open Access

    Optimization of FC-CSP and MLCC Soldering Process Using Type 7 Solder Paste

    by Hye-Min Lee, Mi-Song Kim, Myeongin Kim, Won Sik Hong

    To confirm the possibility of simultaneous bonding between Si chip and multilayer ceramic capacitors (MLCCs), vacuum reflow soldering is performed between a Si chip and each of 2012, 1608, 1005, 0603, and 0402 MLCCs using Type-7 Sn-3.0Ag-0.5Cu (SAC305) and Sn-0.7Cu solder pastes. To enable an unbiased comparison with the vacuum reflow process, the Si chip and MLCCs are bonded via thermo-compression (TC) bonding and hot air reflow soldering, respectively. The maximum void content of Si chip solder joints bonded via vacuum reflow is 8%. At the MLCC solder joints, the void content yielded by vacuum reflow is lower than that yielded by hot air reflow. The bonding strength of the MLCC solder joint afforded by vacuum reflow is higher than that afforded by hot air reflow. Vacuum reflow is superior to hot air reflow in terms of the void content and bonding strength of the MLCC solder joint. After performing a thermal cycle test (TCT), a crack appeared at the Si chip solder joint bonded by TC bonding. The Cu pillar/Sn-2.5Ag bump is susceptible to cracks after the TCT owing to the insufficient bonding layer thickness yielded; however, the SAC305 sample from vacuum reflow is stable. Meanwhile, (Cu,Ni)6Sn5, Ni3P, and Ag3Sn intermetallic compounds are formed at the MLCC solder joints and then further developed after the TCT. The results of this study indicate the possibility of co-bonding Si chip with MLCCs for semiconductor packaging.