ÇKÇetin Karataş

Çetin Karataş

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Çetin Karataş has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Influence of Velocity and Pressure on Residual Stresses During The Backward and Forward Extrusion of AA6061 T6 Aluminium Alloy

    by Ban Bakır, Haithem Aljawad, Faruk Mert, Çetin Karataş

    The extrusion process is considered a cost-effective manufacturing method compared to alternative production techniques, offering excellent mechanical properties and high product quality. Combined extrusion further enhances efficiency by minimizing the need for additional processing steps, thereby saving time and reducing production costs. The die geometry and friction factors play a critical role in determining the success and quality of this process. In this study, AA 6061 T6 aluminium alloy was selected as the billet material to investigate a combined backward–forward extrusion process and to examine the influence of process parameters, such as velocity and pressure, on the residual stresses formed in the extruded products. Two punch types were utilized: a hexagonal punch for the backward extrusion direction and a square punch for the forward extrusion direction. For each punch type, three different cross-sectional areas (140, 130, 115 mm2) and three different forming velocities (0.25, 0.5, 1 mm/s) were tested to assess the effect of forming pressure on residual stresses. The experiments were conducted using a heat-treated H13 steel die with a hydraulic press under lubricated conditions. The findings indicate that increasing the cross-sectional area of the punch, which corresponds to a reduction in pressing pressure, results in higher residual stresses at a constant velocity. The highest residual stresses were observed in the hexagonal region (1315 MPa), corresponding to the backward extrusion process. Intermediate stress levels (


  • Open Access

    İndüksiyon ile Sıcak Şekillendirmede Etkin Kalıp Isıtma Parametrelerin Sayısal Analizi

    by Emre Erol, Tayfun Menlik, Çetin Karataş, Adnan Sözen

    Günümüzde özellikle havacılık ve otomotiv sektörlerinde yakıt tasarrufu sağlamak için en etkin yöntemlerden biri ağırlık azaltmaktır. Bu nedenle yüksek mukavemet gereken yerlerde görece daha düşük özgül ağırlığa sahip malzemeler tercih edilmektedir. Bu özelliğe sahip malzemelerin şekillendirilebilme kabiliyetleri genellikle soğuk şekillendirme için uygun değildir. Bu sebeple sıcak şekillendirme yöntemleri tercih edilmektedir. Bu yöntemler arasında hızlı sıcaklık artışı sağlaması, çevre dostu olması ve düşük enerji tüketimi gibi özelliklere sahip olması nedeniyle yenilikçi indüksiyon ile sıcak şekillendirme yöntemi öne çıkmaktadır. Bu çalışmada indüksiyon ile sıcak şekillendirme sırasında kalıbın istenilen sıcaklığa en hızlı ve uygun şekilde gelebilmesi için etkin parametrelerin tespiti ve sayısal analizi yapılmıştır. Yapılan çalışmada, tasarlanan kalıp ve dörtgensel bobin modeli farklı akım değerlerine göre sonlu elemanlar metodu ile analiz edilmiştir. Sırasıyla 601A, 726A ve 828A akım değerleri sisteme verilmiş ve istenilen sıcaklığa 828A değerinde ulaşılmıştır. Tüm akım değerlerine göre termal gerilim hesabı matematiksel olarak hesaplanmış ve hiçbir akım değerinde termal çatlağa sebebiyet verecek bir değere ulaşılmadığı görülmüştür.

  • Open Access

    Investigation of Sinterability of WC-Co Component Comprising of AISI 4340 Steel Inserts

    by Mehmet Subaşi, Harun Koçak, Asghar Safari̇an, Çetin Karataş

    In this study, sinterability of WC-9% Co component with AISI 4340 steel insert was investigated using Inserted Powder Injection Molding (IPIM) method. Sintering experiments were performed at temperatures of 1200 °C to 1350 °C with dwell times of 120, 240, 360 min. Defects such as gaps, cracks and macro-porosities were observed in specimens, sintered at temperatures of 1200 °C and 1250 °C for all dwell times. It was proved that sintering temperature of 1350 °C was as high as it caused insert to get deformed and melted. As a result, the optimum sintering temperature and dwell time were determined to be 1300 °C and 240 min, respectively, at which the highest hardness, compression strength, and sintered density were obtained without any defects such as cracks or gaps.

  • Investigation of earing defect and thickness distribution in stamp forming of continuous glass fiber reinforced polypropylene composite laminates

    by A Onur Özdemir, Cetin Karatas, Harun Kocak, Murat Demiral

    When lightweighting studies are examined, thermoplastic matrix composites come to the fore as they have a high specific strength, are recyclable, and can be formed by thermoforming. Some obscurity needs to be overcome for the rapid forming of three-dimensional parts from laminated thermoplastic composites. In this study, deep drawing experiments were carried out to investigate the forming capabilities of continuous glass fiber reinforced polypropylene composite laminates. The parameters of drawing depth, laminate temperature, holding pressure, and punch speed were examined at each three different levels. The effects of these parameters were evaluated on the earing defect and the thickness distribution. It was concluded that the laminate temperature affected both deformations the most. It was determined that all parameters caused a change in flange diameter, but the amount of earing increased with the increase of drawing depth. It was established that inhomogeneous thickness distributions occurred in the part and the highest thickening took place in the curve region.


  • Tungsten Karbür Besleme Stoğundan Elde Edilen Parçalar İçin İdeal Çözücünün Araştırılması

    by Kamran Samet, Mehmet Subaşi, Çetin Karataş

    Bu çalışmada tungsten karbür - kobalt (WC-Co) besleme stoğundan Toz Enjeksiyon Kalıplama (TEK) yöntemi ile elde edilmiş numunelerin kimyasal bağlayıcı aşamasında kullanılacak çözücü türü araştırılmıştır. TEK yöntemi ile WC-Co besleme stoğundan hazırlanan deney numunelerinin kimyasal bağlayıcı giderme deneyleri onüç farklı çözücü (Toluen, Benzen, Heptan, Aseton, Etanol, Karbon tetraklorür (CCl4), Etanol+ Karbon tetraklorür (CCl4), Metanol, Nitrik asit, Hidroklorik asit, Sülfürik asit, Kloroform, Dikloroetan) kullanılarak gerçekleştirilmiştir. Deneyler sonucunda WC-Co besleme stoğu için bulunabilirlik ve maliyet açısından en ideal çözücünün etanol olduğu belirlenmiştir. Ayrıca deneyler sonucunda 60 °C sıcaklık ve 60 saat sürede etanol içerisinde tutulan parçalarda hedeflenen sonuçların elde edildiği belirlenmiştir.

  • Investigating the Effects of Forming Parameters on Molding Force and Springback in Deep Drawing Process of Thermoplastic Composite Laminates

    by Abdullah Onur Özdemi̇r, Mehmet Subaşi Subaşi, Çetin Karataş

    The automotive industry and research centers have intensified the search for innovative solutions in the field of material technologies and have recently accelerated their work on thermoplastic based composites in line with their requirements. Thermoform method is used for rapid forming of thermoplastics and composites. In this process, mold design and especially molding parameters are important for part quality. Thermoplastic composite sheets take the shape of their final form by spring back after they come out of the mold as in sheet metals. Therefore, springback is a parameter that should be taken into account in the manufacturing process and product design. In this study, preliminary research was carried out to design the forming process in thermoform mold. The experiments were done on Nakajima test setup and according to ISO 12004 standard. In the deep drawing of thermoplastic composite laminates, the effects of different holding pressure (0.4; 0.6; 0.8 MPa), punch speed (90, 120, 150 mm/min), specimen temperature (129, 159, 169 oC) and piece depth (20, 25, 30 mm) parameters on the molding force were examined and the spring back amount of deep drawn specimens was determined. As a result of the experiments, as the specimen temperature increased the molding force decreased. The molding force increased as the holding pressure increased. Increasing punch speed caused an increase in required molding force. As a result of the experiments, it was concluded that deep drawing can be made up to a depth of 25 mm.


  • Elyaf Konfigürasyonunun Termoplastik Kompozit Levhaların Mekanik Özelliklerine Etkisi

    by Abdullah Onur Özdemi̇r, Çetin Karataş, Serdar Yücesu

    Kompozit malzemeler birden fazla bileşenin bir araya gelmesiyle oluşan malzemelerdir. Termoplastik kompozit malzemeler, işlevsel özellikleri nedeniyle çeşitli endüstriyel uygulamalarda yaygın olarak kullanılmaktadır. Sürekli (dokunmuş veya tek yönlü dokunmamış) elyaf ile reçine tabakalarının kombinasyonu levha halinde kompozit olarak tanımlanmaktadır. Cam elyaf, kompozit levhaların imalatında ümit verici ve rekabet edebilir malzemelerden biridir. Elyaf içeriği kompozit malzemelerin mekanik özelliklerini etkilediğinden dolayı önemlidir. Bu çalışmada, elyaf konfigürasyonu farklı olan termoplastik kompozit levhaların çekme, basma ve darbe özellikleri deneysel olarak incelenmiştir. Malzemelerin mühendislik uygulamalarında etkin kullanımı için maruz kaldıkları yüklere ilişkin bu mekanik özelliklerin bilinmesi esastır. Matriks elemanı polipropilen olan kompozit malzemelerin takviye elemanı dört çeşit konfigürasyona sahip kırpılmış-dokunmuş cam elyaftır. Numuneler, su jetiyle standartlara uygun ölçülerde kesilmiştir. Boyuna ve enine yönlerde hazırlanan numunelerin mekanik testleri oda sıcaklığında gerçekleştirilmiştir. Malzemelerin gerinim-gerilim eğrileri oluşturulmuş, elastik modül değerleri hesaplanmış, çekme, basma ve darbe dayanımları belirlenerek grafikler üzerinde karşılaştırılmıştır. Kompozitlerin mekanik özellikleri dokuma yönüne ve lif oranına bağlı olarak değişkenlik göstermiştir. Dokunmuş elyaf katı ve elyaf oranı en fazla olan kompozit levhanın dayanımı ve birim uzaması en fazla çıkmıştır.


  • İNSÖRTLÜ TOZ ENJEKSİYON KALIPLAMADA İNSÖRT MALZEMESİNİN ARAŞTIRILMASI

    by Mehmet Subaşi, Kamran Samet, Çetin Karataş

    İnsörtlü toz enjeksiyon kalıplama (İTEK) kalın parçaların (>10 mm) üretilebilmesi için geliştirilmiş bir yöntemdir. Bu yöntemde önceden hazırlanmış insörtler üzerine besleme stoku enjekte edilir. Enjeksiyon işleminden sonra kalıplanan parçalara bağlayıcı giderme ve sinterleme işlemleri uygulanır. Bu çalışmada, İTEK yöntemi ile üretilecek parçalarda, insört malzemesinin uygunluğu ve etkileri araştırılmıştır. Deneylerde tungusten karbür kobalt (WC-%9Co) besleme stoku kullanılmıştır. İnsört malzemesinin etkilerini belirlemek için 1020, 1050, 2312, 2344, 2379 ve 4140 çeliklerinden insörtler hazırlanmıştır. Bu insörtler üzerine WC besleme stoku enjekte edildikten sonra 1200, 1250 ve 1400 °C derecelerde ve 60, 180 ve 240 dakika sürelerde sinterleme işlemleri yapılmıştır. Deneyler sonucunda 1400°C sinterleme sıcaklığında tüm insörtlerin eridiği, 1200 °C ve 1250 °C sıcaklıklarda ise geometrik formlarını koruduğu belirlenmiştir. Fakat bu sıcaklıklarda (1200 °C - 1250 °C) insört ile enjekte bölge arasında bir birleşme oluşmadığı belirlenmiştir.


  • Investigation of functional core-rim composite part production by inserted powder injection moulding

    by Mehmet Subaşi, Harun Koçak, Asghar Safarian, Çetin Karataş

    In this study, the use of Cu and Ni interlayers have been investigated for functional core-rim composite part production with WC-Co 9 wt-% feedstock/steel. For this purpose, different experiments have been performed and joining condition, shear strength and microstructure of the intermediate region have been examined. It has been found that AISI 4340 insert/WC-Co have been joined and 85.8 MPa shear strength achieved, but high speed steel insert has not joined. Moreover, it has been determined that better results are obtained with Ni interlayer. Under the same conditions, when the 40 µm Ni interlayer has been used between AISI 4340 core and WC-Co rim, shear strength has been increased approximately twice and has been 162.7 MPa.