Mehmet Subasi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Mehmet Subasi has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Çetin Karataş
Gazi Üniversitesi
5 shared publications C Kesemenli
4 shared publicationsA Kapukaya
3 shared publicationsAhmet Kapukaya
3 shared publications- Emre Ayhan
Department of Electronics and Automation, Technical Sciences Vocational School, Gazi University, Ostim, Ankara 06374, Türkiye
3 shared publications - Hacı Bekir Özerkan
Mechanical Engineering Department, Gazi University, Ankara, Turkey
3 shared publications
Latest Publications
- Open Access
Material Removal and Dimensional Accuracy in Electrical Discharge Turning of AISI 4140 Steel Under Lateral Flushing and Full Immersion
Electrical discharge machining (EDM) offers certain advantages as a thermal process but also has drawbacks. A hybrid system called electrical discharge turning (EDT), which combines traditional turning with EDM, has been developed to overcome these. In this study, experiments were conducted using a copper electrode and cylindrical AISI 4140 tempered steel with a diameter of 12 mm. The experimental design was planned as a full factorial analysis, and the effects of parameters such as dielectric medium, machining depth, discharge current, and workpiece rotational speed on surface roughness (Ra), material removal rate (MRR), tool wear rate (TWR) and dimensional accuracy were investigated. Pulse-on time, pulse-off time and lateral flushing pressure were kept constant. In the experiments, an increase in discharge current increased surface roughness, MRR, and TWR, while an increase in workpiece rotational speed showed similar effects. The effect of discharge current on performance outputs was found to be more pronounced compared to rotational speed. The dielectric medium had no statistically significant main effect on any response. Because the achieved machining depths fell 26–83% short of the intended values, first- and second-order regression models and an XGBoost model based only on controllable process parameters were developed to estimate the depth to be set on the machine. In leave-one-out cross-validation, the second-order regression model (R2 = 0.85, RMSE = 0.56 mm) and the XGBoost model (nested; R2 = 0.82, RMSE = 0.61 mm) clearly outperformed the first-order linear model (R2 = 0.67, RMSE = 0.83 mm); these models require verification with independent experiments before practical use.
Open AccessMaterial Removal and Dimensional Accuracy in Electrical Discharge Turning of AISI 4140 Steel Under Lateral Flushing and Full Immersion
Electrical discharge machining (EDM) offers certain advantages as a thermal process but also has drawbacks. A hybrid system called electrical discharge turning (EDT), which combines traditional turning with EDM, has been developed to overcome these. In this study, experiments were conducted using a copper electrode and cylindrical AISI 4140 tempered steel with a diameter of 12 mm. The experimental design was planned as a full factorial analysis, and the effects of parameters such as dielectric medium, machining depth, discharge current, and workpiece rotational speed on surface roughness (Ra), material removal rate (MRR), tool wear rate (TWR) and dimensional accuracy were investigated. Pulse-on time, pulse-off time and lateral flushing pressure were kept constant. In the experiments, an increase in discharge current increased surface roughness, MRR, and TWR, while an increase in workpiece rotational speed showed similar effects. The effect of discharge current on performance outputs was found to be more pronounced compared to rotational speed. The dielectric medium had no statistically significant main effect on any response. Because the achieved machining depths fell 26–83% short of the intended values, first- and second-order regression models and an XGBoost model based only on controllable process parameters were developed to estimate the depth to be set on the machine. In leave-one-out cross-validation, the second-order regression model (R2 = 0.85, RMSE = 0.56 mm) and the XGBoost model (nested; R2 = 0.82, RMSE = 0.61 mm) clearly outperformed the first-order linear model (R2 = 0.67, RMSE = 0.83 mm); these models require verification with independent experiments before practical use.
- Open Access
- 1 January 2026
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 65 (1)
Electro discharge turning of Ti–6Al–4V alloy: experimental investigation and RSM model
This study investigates the machinability of Ti–6Al–4V alloy using electro discharge turning (EDT), with particular focus on the effects of current ( I p ), pulse duration ( T on ), and workpiece rotational speed ( v ) on process performance. While conventional evaluation metrics such as material removal rate (MRR) and tool wear rate (TWR) were considered, a novel metric, the deviation of section area (DA), was introduced to provide deeper insights into the dimensional accuracy of the process. The introduction of DA is expected to improve understanding of the complex physical phenomena inherent to EDM-based processes. Experimental results were analyzed using response surface methodology (RSM), yielding statistical models and regression equations. The findings highlight the critical influence of process parameters on machining performance, demonstrate the potential of EDT as an effective method for machining Ti–6Al–4V alloys, and establish DA as a promising performance indicator for future studies.
- 1 January 2026
- Published by Walter de Gruyter GmbH in REVIEWS ON ADVANCED MATERIALS SCIENCE
- Vol. 65 (1)
Open AccessElectro discharge turning of Ti–6Al–4V alloy: experimental investigation and RSM model
This study investigates the machinability of Ti–6Al–4V alloy using electro discharge turning (EDT), with particular focus on the effects of current ( I p ), pulse duration ( T on ), and workpiece rotational speed ( v ) on process performance. While conventional evaluation metrics such as material removal rate (MRR) and tool wear rate (TWR) were considered, a novel metric, the deviation of section area (DA), was introduced to provide deeper insights into the dimensional accuracy of the process. The introduction of DA is expected to improve understanding of the complex physical phenomena inherent to EDM-based processes. Experimental results were analyzed using response surface methodology (RSM), yielding statistical models and regression equations. The findings highlight the critical influence of process parameters on machining performance, demonstrate the potential of EDT as an effective method for machining Ti–6Al–4V alloys, and establish DA as a promising performance indicator for future studies.
- Open Access
- 18 December 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1)
Parametric optimization of graphite powder-mixed electrical discharge machining of Ni-Cr dental alloy by response surface methodology
In this study, the effects of machining parameters on material removal rate (MRR), electrode wear rate (EWR) and surface roughness (Ra) in the electrical discharge machining (EDM) of nickel-chromium-based alloy were investigated. Discharge current (I), pulse-on time (Ton), pulse-off time (Toff) and graphite powder concentration were selected as variable parameters in the study. An experimental setup was designed and manufactured for use in powder-mixed EDM experiments. Mathematical models were generated using response surface methodology (RSM), the most effective parameters on the results were determined and regression equations were obtained. Parameter optimization was performed with the highest MRR, lowest EWR, and lowest Ra performance targets. The ideal machining conditions were determined as I = 12.5 A, Ton=66µs, Toff=6µs and powder-mixed dielectric. Using the powder-mixed dielectric, 34.54% higher MRR, 20.01% lower EWR and 12.64% lower Ra were achieved on average. Using the created mathematical model, the result of the machining to be done with these parameters was predicted and the reliability of the model was tested by comparing the predicted results of the model and the results of the verification experiment.
- 18 December 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1)
Open AccessParametric optimization of graphite powder-mixed electrical discharge machining of Ni-Cr dental alloy by response surface methodology
In this study, the effects of machining parameters on material removal rate (MRR), electrode wear rate (EWR) and surface roughness (Ra) in the electrical discharge machining (EDM) of nickel-chromium-based alloy were investigated. Discharge current (I), pulse-on time (Ton), pulse-off time (Toff) and graphite powder concentration were selected as variable parameters in the study. An experimental setup was designed and manufactured for use in powder-mixed EDM experiments. Mathematical models were generated using response surface methodology (RSM), the most effective parameters on the results were determined and regression equations were obtained. Parameter optimization was performed with the highest MRR, lowest EWR, and lowest Ra performance targets. The ideal machining conditions were determined as I = 12.5 A, Ton=66µs, Toff=6µs and powder-mixed dielectric. Using the powder-mixed dielectric, 34.54% higher MRR, 20.01% lower EWR and 12.64% lower Ra were achieved on average. Using the created mathematical model, the result of the machining to be done with these parameters was predicted and the reliability of the model was tested by comparing the predicted results of the model and the results of the verification experiment.
- Open Access
- 1 December 2023
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 36 (4) , 1722-1731
Investigation of Sinterability of WC-Co Component Comprising of AISI 4340 Steel Inserts
In this study, sinterability of WC-9% Co component with AISI 4340 steel insert was investigated using Inserted Powder Injection Molding (IPIM) method. Sintering experiments were performed at temperatures of 1200 °C to 1350 °C with dwell times of 120, 240, 360 min. Defects such as gaps, cracks and macro-porosities were observed in specimens, sintered at temperatures of 1200 °C and 1250 °C for all dwell times. It was proved that sintering temperature of 1350 °C was as high as it caused insert to get deformed and melted. As a result, the optimum sintering temperature and dwell time were determined to be 1300 °C and 240 min, respectively, at which the highest hardness, compression strength, and sintered density were obtained without any defects such as cracks or gaps.
- 1 December 2023
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 36 (4) , 1722-1731
Open AccessInvestigation of Sinterability of WC-Co Component Comprising of AISI 4340 Steel Inserts
In this study, sinterability of WC-9% Co component with AISI 4340 steel insert was investigated using Inserted Powder Injection Molding (IPIM) method. Sintering experiments were performed at temperatures of 1200 °C to 1350 °C with dwell times of 120, 240, 360 min. Defects such as gaps, cracks and macro-porosities were observed in specimens, sintered at temperatures of 1200 °C and 1250 °C for all dwell times. It was proved that sintering temperature of 1350 °C was as high as it caused insert to get deformed and melted. As a result, the optimum sintering temperature and dwell time were determined to be 1300 °C and 240 min, respectively, at which the highest hardness, compression strength, and sintered density were obtained without any defects such as cracks or gaps.
- Open Access
- 1 January 2023
- Published by National Library of Serbia in Science of Sintering
- Vol. 55 (1) , 89-101
The effect of insert surface roughness in part production with inserted powder injection molding method
The Powder Injection Molding (PIM) method is widely used in the production of parts with complex geometries and small volumes. To solve the volume limitation in PIM, the Inserted Powder Injection Molding (IPIM) method was developed. In this study, the effect of insert surface roughness on shear strength was investigated using the IPIM method in the production of WC-9%Co parts. Firstly, inserts with five different surface roughness (Ra, ?m), 1.5 - 2.1 - 3.3 - 4 - 4.6, were prepared from 4340 steel for the research. WC feedstock was injected onto the prepared inserts. Following the injection process, the samples were subjected to debinding and sintering processes. Compression tests were performed on sintered specimens, and the effect of surface roughness on diffusion bonding strength was investigated. As a result of the experiments, it was determined that the shear strength increases with the increase of the insert surface roughness. The maximum shear strength (118.4 MPa) was obtained in samples with an insert surface roughness of 4.6 ?m.
- 1 January 2023
- Published by National Library of Serbia in Science of Sintering
- Vol. 55 (1) , 89-101
Open AccessThe effect of insert surface roughness in part production with inserted powder injection molding method
The Powder Injection Molding (PIM) method is widely used in the production of parts with complex geometries and small volumes. To solve the volume limitation in PIM, the Inserted Powder Injection Molding (IPIM) method was developed. In this study, the effect of insert surface roughness on shear strength was investigated using the IPIM method in the production of WC-9%Co parts. Firstly, inserts with five different surface roughness (Ra, ?m), 1.5 - 2.1 - 3.3 - 4 - 4.6, were prepared from 4340 steel for the research. WC feedstock was injected onto the prepared inserts. Following the injection process, the samples were subjected to debinding and sintering processes. Compression tests were performed on sintered specimens, and the effect of surface roughness on diffusion bonding strength was investigated. As a result of the experiments, it was determined that the shear strength increases with the increase of the insert surface roughness. The maximum shear strength (118.4 MPa) was obtained in samples with an insert surface roughness of 4.6 ?m.
- 17 September 2021
- Published by Bitlis Eren Universitesi Fen Bilimleri Dergisi in Bitlis Eren Üniversitesi Fen Bilimleri Dergisi
- Vol. 10 (3) , 1168-1174
Tungsten Karbür Besleme Stoğundan Elde Edilen Parçalar İçin İdeal Çözücünün Araştırılması
Bu çalışmada tungsten karbür - kobalt (WC-Co) besleme stoğundan Toz Enjeksiyon Kalıplama (TEK) yöntemi ile elde edilmiş numunelerin kimyasal bağlayıcı aşamasında kullanılacak çözücü türü araştırılmıştır. TEK yöntemi ile WC-Co besleme stoğundan hazırlanan deney numunelerinin kimyasal bağlayıcı giderme deneyleri onüç farklı çözücü (Toluen, Benzen, Heptan, Aseton, Etanol, Karbon tetraklorür (CCl4), Etanol+ Karbon tetraklorür (CCl4), Metanol, Nitrik asit, Hidroklorik asit, Sülfürik asit, Kloroform, Dikloroetan) kullanılarak gerçekleştirilmiştir. Deneyler sonucunda WC-Co besleme stoğu için bulunabilirlik ve maliyet açısından en ideal çözücünün etanol olduğu belirlenmiştir. Ayrıca deneyler sonucunda 60 °C sıcaklık ve 60 saat sürede etanol içerisinde tutulan parçalarda hedeflenen sonuçların elde edildiği belirlenmiştir.
- 17 September 2021
- Published by Bitlis Eren Universitesi Fen Bilimleri Dergisi in Bitlis Eren Üniversitesi Fen Bilimleri Dergisi
- Vol. 10 (3) , 1168-1174
Tungsten Karbür Besleme Stoğundan Elde Edilen Parçalar İçin İdeal Çözücünün Araştırılması
Bu çalışmada tungsten karbür - kobalt (WC-Co) besleme stoğundan Toz Enjeksiyon Kalıplama (TEK) yöntemi ile elde edilmiş numunelerin kimyasal bağlayıcı aşamasında kullanılacak çözücü türü araştırılmıştır. TEK yöntemi ile WC-Co besleme stoğundan hazırlanan deney numunelerinin kimyasal bağlayıcı giderme deneyleri onüç farklı çözücü (Toluen, Benzen, Heptan, Aseton, Etanol, Karbon tetraklorür (CCl4), Etanol+ Karbon tetraklorür (CCl4), Metanol, Nitrik asit, Hidroklorik asit, Sülfürik asit, Kloroform, Dikloroetan) kullanılarak gerçekleştirilmiştir. Deneyler sonucunda WC-Co besleme stoğu için bulunabilirlik ve maliyet açısından en ideal çözücünün etanol olduğu belirlenmiştir. Ayrıca deneyler sonucunda 60 °C sıcaklık ve 60 saat sürede etanol içerisinde tutulan parçalarda hedeflenen sonuçların elde edildiği belirlenmiştir.
- 1 June 2021
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 34 (2) , 506-515
Investigating the Effects of Forming Parameters on Molding Force and Springback in Deep Drawing Process of Thermoplastic Composite Laminates
The automotive industry and research centers have intensified the search for innovative solutions in the field of material technologies and have recently accelerated their work on thermoplastic based composites in line with their requirements. Thermoform method is used for rapid forming of thermoplastics and composites. In this process, mold design and especially molding parameters are important for part quality. Thermoplastic composite sheets take the shape of their final form by spring back after they come out of the mold as in sheet metals. Therefore, springback is a parameter that should be taken into account in the manufacturing process and product design. In this study, preliminary research was carried out to design the forming process in thermoform mold. The experiments were done on Nakajima test setup and according to ISO 12004 standard. In the deep drawing of thermoplastic composite laminates, the effects of different holding pressure (0.4; 0.6; 0.8 MPa), punch speed (90, 120, 150 mm/min), specimen temperature (129, 159, 169 oC) and piece depth (20, 25, 30 mm) parameters on the molding force were examined and the spring back amount of deep drawn specimens was determined. As a result of the experiments, as the specimen temperature increased the molding force decreased. The molding force increased as the holding pressure increased. Increasing punch speed caused an increase in required molding force. As a result of the experiments, it was concluded that deep drawing can be made up to a depth of 25 mm.
- 1 June 2021
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 34 (2) , 506-515
Investigating the Effects of Forming Parameters on Molding Force and Springback in Deep Drawing Process of Thermoplastic Composite Laminates
The automotive industry and research centers have intensified the search for innovative solutions in the field of material technologies and have recently accelerated their work on thermoplastic based composites in line with their requirements. Thermoform method is used for rapid forming of thermoplastics and composites. In this process, mold design and especially molding parameters are important for part quality. Thermoplastic composite sheets take the shape of their final form by spring back after they come out of the mold as in sheet metals. Therefore, springback is a parameter that should be taken into account in the manufacturing process and product design. In this study, preliminary research was carried out to design the forming process in thermoform mold. The experiments were done on Nakajima test setup and according to ISO 12004 standard. In the deep drawing of thermoplastic composite laminates, the effects of different holding pressure (0.4; 0.6; 0.8 MPa), punch speed (90, 120, 150 mm/min), specimen temperature (129, 159, 169 oC) and piece depth (20, 25, 30 mm) parameters on the molding force were examined and the spring back amount of deep drawn specimens was determined. As a result of the experiments, as the specimen temperature increased the molding force decreased. The molding force increased as the holding pressure increased. Increasing punch speed caused an increase in required molding force. As a result of the experiments, it was concluded that deep drawing can be made up to a depth of 25 mm.
- Open Access
- 25 October 2020
- Published by Academic Perspective in Academic Perspective Procedia
- Vol. 3 (1) , 686-693
Toz enjeksiyon kalıplamada iç vida profilinin maça kullanmadan elde edilmesinin araştırılması
Toz enjeksiyon kalıplama (TEK) metal ve seramik tozlarından karmaşık şekilli küçük hacimli parçaların kitlesel üretilmelerinde kullanılan bir tekniktir. Bu yöntem besleme stoku hazırlama, kalıplama, bağlayıcı giderme ve sinterleme aşamalarından meydana gelmektedir
- 25 October 2020
- Published by Academic Perspective in Academic Perspective Procedia
- Vol. 3 (1) , 686-693
Open AccessToz enjeksiyon kalıplamada iç vida profilinin maça kullanmadan elde edilmesinin araştırılması
Toz enjeksiyon kalıplama (TEK) metal ve seramik tozlarından karmaşık şekilli küçük hacimli parçaların kitlesel üretilmelerinde kullanılan bir tekniktir. Bu yöntem besleme stoku hazırlama, kalıplama, bağlayıcı giderme ve sinterleme aşamalarından meydana gelmektedir
- 28 June 2020
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 8 (2) , 475-485
İNSÖRTLÜ TOZ ENJEKSİYON KALIPLAMADA İNSÖRT MALZEMESİNİN ARAŞTIRILMASI
İnsörtlü toz enjeksiyon kalıplama (İTEK) kalın parçaların (>10 mm) üretilebilmesi için geliştirilmiş bir yöntemdir. Bu yöntemde önceden hazırlanmış insörtler üzerine besleme stoku enjekte edilir. Enjeksiyon işleminden sonra kalıplanan parçalara bağlayıcı giderme ve sinterleme işlemleri uygulanır. Bu çalışmada, İTEK yöntemi ile üretilecek parçalarda, insört malzemesinin uygunluğu ve etkileri araştırılmıştır. Deneylerde tungusten karbür kobalt (WC-%9Co) besleme stoku kullanılmıştır. İnsört malzemesinin etkilerini belirlemek için 1020, 1050, 2312, 2344, 2379 ve 4140 çeliklerinden insörtler hazırlanmıştır. Bu insörtler üzerine WC besleme stoku enjekte edildikten sonra 1200, 1250 ve 1400 °C derecelerde ve 60, 180 ve 240 dakika sürelerde sinterleme işlemleri yapılmıştır. Deneyler sonucunda 1400°C sinterleme sıcaklığında tüm insörtlerin eridiği, 1200 °C ve 1250 °C sıcaklıklarda ise geometrik formlarını koruduğu belirlenmiştir. Fakat bu sıcaklıklarda (1200 °C - 1250 °C) insört ile enjekte bölge arasında bir birleşme oluşmadığı belirlenmiştir.
- 28 June 2020
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 8 (2) , 475-485
İNSÖRTLÜ TOZ ENJEKSİYON KALIPLAMADA İNSÖRT MALZEMESİNİN ARAŞTIRILMASI
İnsörtlü toz enjeksiyon kalıplama (İTEK) kalın parçaların (>10 mm) üretilebilmesi için geliştirilmiş bir yöntemdir. Bu yöntemde önceden hazırlanmış insörtler üzerine besleme stoku enjekte edilir. Enjeksiyon işleminden sonra kalıplanan parçalara bağlayıcı giderme ve sinterleme işlemleri uygulanır. Bu çalışmada, İTEK yöntemi ile üretilecek parçalarda, insört malzemesinin uygunluğu ve etkileri araştırılmıştır. Deneylerde tungusten karbür kobalt (WC-%9Co) besleme stoku kullanılmıştır. İnsört malzemesinin etkilerini belirlemek için 1020, 1050, 2312, 2344, 2379 ve 4140 çeliklerinden insörtler hazırlanmıştır. Bu insörtler üzerine WC besleme stoku enjekte edildikten sonra 1200, 1250 ve 1400 °C derecelerde ve 60, 180 ve 240 dakika sürelerde sinterleme işlemleri yapılmıştır. Deneyler sonucunda 1400°C sinterleme sıcaklığında tüm insörtlerin eridiği, 1200 °C ve 1250 °C sıcaklıklarda ise geometrik formlarını koruduğu belirlenmiştir. Fakat bu sıcaklıklarda (1200 °C - 1250 °C) insört ile enjekte bölge arasında bir birleşme oluşmadığı belirlenmiştir.
- 26 December 2019
- Published by SAGE Publications in Materials Science and Technology
- Vol. 36 (3) , 293-298
Investigation of functional core-rim composite part production by inserted powder injection moulding
In this study, the use of Cu and Ni interlayers have been investigated for functional core-rim composite part production with WC-Co 9 wt-% feedstock/steel. For this purpose, different experiments have been performed and joining condition, shear strength and microstructure of the intermediate region have been examined. It has been found that AISI 4340 insert/WC-Co have been joined and 85.8 MPa shear strength achieved, but high speed steel insert has not joined. Moreover, it has been determined that better results are obtained with Ni interlayer. Under the same conditions, when the 40 µm Ni interlayer has been used between AISI 4340 core and WC-Co rim, shear strength has been increased approximately twice and has been 162.7 MPa.
- 26 December 2019
- Published by SAGE Publications in Materials Science and Technology
- Vol. 36 (3) , 293-298
Investigation of functional core-rim composite part production by inserted powder injection moulding
In this study, the use of Cu and Ni interlayers have been investigated for functional core-rim composite part production with WC-Co 9 wt-% feedstock/steel. For this purpose, different experiments have been performed and joining condition, shear strength and microstructure of the intermediate region have been examined. It has been found that AISI 4340 insert/WC-Co have been joined and 85.8 MPa shear strength achieved, but high speed steel insert has not joined. Moreover, it has been determined that better results are obtained with Ni interlayer. Under the same conditions, when the 40 µm Ni interlayer has been used between AISI 4340 core and WC-Co rim, shear strength has been increased approximately twice and has been 162.7 MPa.